ITI Turner 1st Year Mock Test – 8 July 16, 2025 ITI Turner 1st Year Mock Test – 8 | Instant Feedback ITI Turner 1st Year Mock Test – 8 आईटीआई टर्नर प्रथम वर्ष मॉक टेस्ट – 8 Time Left: 30:00 Test Complete! 1. What is a key electrical safety measure when working on any machine?1. किसी भी मशीन पर काम करते समय एक प्रमुख विद्युत सुरक्षा उपाय क्या है? a) Wearing metal jewelry / धातु के आभूषण पहनना b) Ensuring proper machine earthing and checking for damaged wires / उचित मशीन अर्थिंग सुनिश्चित करना और क्षतिग्रस्त तारों की जांच करना c) Working with wet hands / गीले हाथों से काम करना d) Bypassing safety switches / सुरक्षा स्विच को बायपास करना 2. The operation of producing multiple diameters on a workpiece is known as:2. एक वर्कपीस पर कई व्यास बनाने की प्रक्रिया कहलाती है: a) Taper turning / टेपर टर्निंग b) Plain turning / प्लेन टर्निंग c) Step turning / स्टेप टर्निंग d) Facing / फेसिंग 3. Parallax error in measurement occurs due to:3. माप में लंबन त्रुटि (Parallax error) किसके कारण होती है: a) A faulty instrument / एक दोषपूर्ण उपकरण b) Incorrect viewing angle of the operator / ऑपरेटर का गलत देखने का कोण c) Temperature changes / तापमान परिवर्तन d) Wear and tear of the instrument / उपकरण की टूट-फूट 4. The part of the lathe that holds and rotates the workpiece is the:4. लेथ का वह हिस्सा जो वर्कपीस को पकड़ता और घुमाता है, वह है: a) Tailstock / टेलस्टॉक b) Headstock / हेडस्टॉक c) Carriage / कैरिज d) Bed / बेड 5. Thread cutting on a lathe requires a precise relationship between the spindle rotation and the:5. लेथ पर चूड़ी काटने के लिए स्पिंडल के घूर्णन और किसके बीच एक सटीक संबंध की आवश्यकता होती है: a) Movement of the tailstock / टेलस्टॉक की गति b) Linear movement of the carriage / कैरिज की रैखिक गति c) Speed of the coolant pump / कूलेंट पंप की गति d) Angle of the compound slide / कंपाउंड स्लाइड का कोण 6. The primary property of HSS that makes it a good cutting tool material is its:6. HSS का प्राथमिक गुण जो इसे एक अच्छा कटिंग टूल सामग्री बनाता है, वह है इसका: a) Low cost / कम लागत b) Light weight / हल्का वजन c) Hot hardness (ability to stay hard at high temperatures) / हॉट हार्डनेस (उच्च तापमान पर कठोर बने रहने की क्षमता) d) Corrosion resistance / संक्षारण प्रतिरोध 7. Centering a square job on a lathe is done using a:7. लेथ पर एक चौकोर जॉब को केंद्रित करने के लिए इसका उपयोग किया जाता है: a) Three-jaw chuck / थ्री-जॉ चक b) Four-jaw independent chuck / फोर-जॉ इंडिपेंडेंट चक c) Collet chuck / कोलेट चक d) Faceplate / फेसप्लेट 8. A tool signature is a standardized system for specifying:8. एक टूल सिग्नेचर किसके विनिर्देशन के लिए एक मानकीकृत प्रणाली है: a) The tool’s manufacturer / टूल के निर्माता b) The geometry and angles of a single-point cutting tool / एक सिंगल-पॉइंट कटिंग टूल की ज्यामिति और कोण c) The tool’s price / टूल की कीमत d) The material of the tool / टूल की सामग्री 9. Counterboring is done to:9. काउंटरबोरिंग की जाती है: a) Create a conical seat for a screw head / एक स्क्रू हेड के लिए एक शंक्वाकार सीट बनाने के लिए b) Create a flat-bottomed enlargement for a bolt head or nut / एक बोल्ट हेड या नट के लिए एक सपाट-तल वाला विस्तार बनाने के लिए c) Finish a hole to a very precise size / एक छेद को बहुत सटीक आकार तक फिनिश करने के लिए d) Cut threads in a hole / एक छेद में चूड़ियाँ काटने के लिए 10. The main purpose of tempering steel after it has been hardened is to:10. कठोर किए गए स्टील को टेम्पर करने का मुख्य उद्देश्य है: a) Make it even harder / इसे और भी कठोर बनाना b) Make it softer / इसे नरम बनाना c) Reduce brittleness and increase toughness / भंगुरता को कम करना और टफनेस बढ़ाना d) Clean the surface / सतह को साफ करना 11. A depth micrometer is used for measuring the:11. एक डेप्थ माइक्रोमीटर का उपयोग मापने के लिए किया जाता है: a) Outside diameter of a shaft / एक शाफ्ट का बाहरी व्यास b) Depth of holes, slots, and shoulders / छेदों, स्लॉट्स और शोल्डर्स की गहराई c) Pitch of a thread / एक चूड़ी की पिच d) Angle of a taper / एक टेपर का कोण 12. A claw hammer should not be used for striking:12. एक क्लॉ हैमर का उपयोग किस पर चोट करने के लिए नहीं किया जाना चाहिए: a) A wooden workpiece / एक लकड़ी का वर्कपीस b) A nail / एक कील c) A hardened steel chisel or punch / एक कठोर स्टील की छेनी या पंच d) A plastic component / एक प्लास्टिक घटक 13. The part of the lathe that holds the cutting tool is the:13. लेथ का वह हिस्सा जो कटिंग टूल को पकड़ता है, वह है: a) Chuck / चक b) Tailstock / टेलस्टॉक c) Tool post / टूल पोस्ट d) Headstock / हेडस्टॉक 14. The most important safety check before starting a pedestal grinder is to:14. एक पेडस्टल ग्राइंडर शुरू करने से पहले सबसे महत्वपूर्ण सुरक्षा जांच है: a) Check the color of the grinding wheel / ग्राइंडिंग व्हील के रंग की जांच करना b) Ensure guards are in place and the tool rest is adjusted correctly / सुनिश्चित करना कि गार्ड अपनी जगह पर हैं और टूल रेस्ट सही ढंग से समायोजित है c) Make sure the machine is well-oiled / यह सुनिश्चित करना कि मशीन अच्छी तरह से तेल से युक्त है d) Wear cotton gloves / सूती दस्ताने पहनना 15. The knurling operation on a lathe is a:15. लेथ पर नर्लिंग ऑपरेशन एक है: a) Cutting operation / कटिंग ऑपरेशन b) Forming operation (material is displaced, not cut) / फॉर्मिंग ऑपरेशन (सामग्री विस्थापित होती है, कटती नहीं) c) Finishing operation / फिनिशिंग ऑपरेशन d) Drilling operation / ड्रिलिंग ऑपरेशन 16. Why should oily rags be stored in a covered metal container?16. तेल से सने चीथड़ों को ढके हुए धातु के कंटेनर में क्यों रखना चाहिए? a) To keep them clean / उन्हें साफ रखने के लिए b) To prevent the risk of spontaneous combustion (catching fire on their own) / स्वतः दहन (अपने आप आग लगने) के जोखिम को रोकने के लिए c) To hide them from the supervisor / उन्हें पर्यवेक्षक से छिपाने के लिए d) To reuse the oil / तेल का पुनः उपयोग करने के लिए 17. A lathe dog is used in conjunction with a:17. एक लेथ डॉग का उपयोग किसके साथ किया जाता है: a) Three-jaw chuck / थ्री-जॉ चक b) Four-jaw chuck / फोर-जॉ चक c) Drive plate or faceplate to drive work between centers / केंद्रों के बीच काम चलाने के लिए एक ड्राइव प्लेट या फेसप्लेट d) Collet chuck / कोलेट चक 18. “Glazing” of a grinding wheel means the:18. एक ग्राइंडिंग व्हील की “ग्लेजिंग” का मतलब है: a) Wheel is new and shiny / व्हील नया और चमकदार है b) Abrasive grains have become dull and the surface is smooth / अपघर्षक कण कुंद हो गए हैं और सतह चिकनी हो गई है c) Wheel pores are clogged with metal particles / व्हील के छिद्र धातु के कणों से भर गए हैं d) Wheel is cracked / व्हील में दरार आ गई है 19. Which of these is a ferrous metal?19. इनमें से कौन एक लौह धातु है? a) Aluminum / एल्यूमीनियम b) Copper / तांबा c) Brass / पीतल d) Cast Iron / कच्चा लोहा 20. What is the function of the side rake angle on a lathe tool?20. लेथ टूल पर साइड रेक एंगल का क्या कार्य है? a) To prevent the tool from rubbing / टूल को रगड़ने से रोकने के लिए b) To control the direction of chip flow / चिप प्रवाह की दिशा को नियंत्रित करने के लिए c) To provide strength to the tool tip / टूल टिप को मजबूती प्रदान करने के लिए d) To set the depth of cut / कट की गहराई सेट करने के लिए 21. The part of the lathe that connects the headstock to the tailstock is the:21. लेथ का वह हिस्सा जो हेडस्टॉक को टेलस्टॉक से जोड़ता है, वह है: a) Carriage / कैरिज b) Bed / बेड c) Lead screw / लीड स्क्रू d) Apron / एप्रन 22. A V-block is used to:22. एक V-ब्लॉक का उपयोग किया जाता है: a) Check squareness / समकोणता की जांच करने के लिए b) Hold cylindrical workpieces for marking and drilling / मार्किंग और ड्रिलिंग के लिए बेलनाकार वर्कपीस को पकड़ने के लिए c) Measure angles / कोणों को मापने के लिए d) Hold flat plates / सपाट प्लेटों को पकड़ने के लिए 23. A file is said to be “pinned” when:23. एक फाइल को “पिन” कहा जाता है जब: a) Its handle is loose / इसका हैंडल ढीला हो b) Its teeth are clogged with small particles / इसके दांत छोटे कणों से भर जाते हैं c) Its teeth are broken / इसके दांत टूट जाते हैं d) It is brand new / यह बिल्कुल नया हो 24. What is the ‘3-point contact’ rule for ladder safety?24. सीढ़ी सुरक्षा के लिए ‘3-पॉइंट संपर्क’ नियम क्या है? a) The ladder must touch the wall at three points / सीढ़ी को तीन बिंदुओं पर दीवार को छूना चाहिए b) Always have either two hands and one foot, or two feet and one hand, on the ladder / हमेशा या तो दो हाथ और एक पैर, या दो पैर और एक हाथ, सीढ़ी पर रखें c) Only three people can use a ladder at a time / एक समय में केवल तीन लोग सीढ़ी का उपयोग कर सकते हैं d) The ladder should be at a 3:1 angle / सीढ़ी 3:1 के कोण पर होनी चाहिए 25. The purpose of annealing a metal is to make it:25. एक धातु को एनीलिंग करने का उद्देश्य उसे बनाना है: a) Harder and more brittle / कठोर और अधिक भंगुर b) Stronger and tougher / मजबूत और टफ c) Softer and more ductile / नरम और अधिक तन्य d) Resistant to corrosion / संक्षारण के प्रतिरोधी ← Previous Next → Finish Test / टेस्ट खत्म करें