ITI Turner 1st Year Mock Test – 9 July 16, 2025 ITI Turner 1st Year Mock Test – 9 | Instant Feedback ITI Turner 1st Year Mock Test – 9 आईटीआई टर्नर प्रथम वर्ष मॉक टेस्ट – 9 Time Left: 30:00 Test Complete! 1. Why is it unsafe to use a file without a handle?1. बिना हैंडल के फाइल का उपयोग करना असुरक्षित क्यों है? a) It provides poor grip / यह खराब पकड़ प्रदान करता है b) The file can break / फाइल टूट सकती है c) The sharp tang can cause serious injury to the hand / नुकीला टैंग हाथ में गंभीर चोट पहुंचा सकता है d) It makes the file heavier / यह फाइल को भारी बनाता है 2. On a lathe, the saddle moves:2. लेथ पर, सैडल चलता है: a) Transversely across the bed / बेड के पार अनुप्रस्थ रूप से b) Longitudinally along the bed ways / बेड वेज़ के साथ अनुदैर्ध्य रूप से c) Vertically up and down / लंबवत रूप से ऊपर और नीचे d) It does not move / यह नहीं चलता है 3. The purpose of the ratchet stop on a micrometer is to:3. एक माइक्रोमीटर पर रैचेट स्टॉप का उद्देश्य है: a) Lock the spindle / स्पिंडल को लॉक करना b) Apply a uniform and limited measuring pressure / एक समान और सीमित मापने का दाब लागू करना c) Help read the measurement / माप पढ़ने में मदद करना d) Move the spindle quickly / स्पिंडल को जल्दी से घुमाना 4. A file with a “safe edge” means that one edge:4. “सेफ एज” वाली फाइल का मतलब है कि एक किनारा: a) Is sharper than the others / दूसरों की तुलना में तेज है b) Is rounded / गोल है c) Has no teeth / पर कोई दांत नहीं है d) Is made of a different material / एक अलग सामग्री से बना है 5. What is the main difference between boring and reaming?5. बोरिंग और रीमिंग के बीच मुख्य अंतर क्या है? a) Boring removes less material than reaming / बोरिंग रीमिंग से कम सामग्री हटाता है b) Boring can correct the position of a hole, while reaming only finishes an existing hole / बोरिंग एक छेद की स्थिति को ठीक कर सकता है, जबकि रीमिंग केवल एक मौजूदा छेद को फिनिश करता है c) Reaming is done before boring / रीमिंग बोरिंग से पहले की जाती है d) Boring is a hand operation, reaming is a machine operation / बोरिंग एक हाथ का ऑपरेशन है, रीमिंग एक मशीन ऑपरेशन है 6. The property of a metal to be drawn into a thin wire is known as:6. एक धातु का वह गुण जो उसे एक पतले तार में खींचे जाने की अनुमति देता है, कहलाता है: a) Malleability / आघातवर्धनीयता b) Hardness / कठोरता c) Ductility / तन्यता d) Toughness / टफनेस 7. The top surface of a screw thread is called the:7. एक स्क्रू थ्रेड की ऊपरी सतह कहलाती है: a) Root / रूट b) Flank / फ्लैंक c) Pitch / पिच d) Crest / क्रेस्ट 8. The bottom surface of a screw thread is called the:8. एक स्क्रू थ्रेड की निचली सतह कहलाती है: a) Root / रूट b) Crest / क्रेस्ट c) Flank / फ्लैंक d) Helix / हेलिक्स 9. What is the purpose of the main scale on a vernier caliper?9. एक वर्नियर कैलिपर पर मुख्य पैमाने का उद्देश्य क्या है? a) To read the fractional part of the measurement / माप के भिन्नात्मक भाग को पढ़ने के लिए b) To read the main whole number part of the measurement / माप के मुख्य पूर्ण संख्या भाग को पढ़ने के लिए c) To lock the sliding jaw / स्लाइडिंग जबड़े को लॉक करने के लिए d) To measure depth / गहराई मापने के लिए 10. What is the main difference in the cooling process between annealing and hardening?10. एनीलिंग और हार्डनिंग के बीच शीतलन प्रक्रिया में मुख्य अंतर क्या है? a) Annealing uses rapid cooling (quenching), hardening uses slow cooling / एनीलिंग में तेजी से ठंडा (क्वेंचिंग) होता है, हार्डनिंग में धीरे-धीरे ठंडा होता है b) Annealing uses slow cooling, hardening uses rapid cooling (quenching) / एनीलिंग में धीरे-धीरे ठंडा होता है, हार्डनिंग में तेजी से ठंडा (क्वेंचिंग) होता है c) Both use the same cooling process / दोनों में एक ही शीतलन प्रक्रिया का उपयोग होता है d) Cooling is not part of these processes / शीतलन इन प्रक्रियाओं का हिस्सा नहीं है 11. A standard drill bit for steel has a lip clearance angle of approximately:11. स्टील के लिए एक मानक ड्रिल बिट का लिप क्लीयरेंस एंगल लगभग होता है: a) 0 to 4 degrees / 0 से 4 डिग्री b) 8 to 12 degrees / 8 से 12 डिग्री c) 20 to 30 degrees / 20 से 30 डिग्री d) 45 degrees / 45 डिग्री 12. In a grinding wheel specification “A 46 K 5 V 17”, the ‘A’ stands for:12. एक ग्राइंडिंग व्हील विनिर्देश “A 46 K 5 V 17” में, ‘A’ का अर्थ है: a) The grade of the wheel / व्हील का ग्रेड b) The type of abrasive (Aluminum Oxide) / अपघर्षक का प्रकार (एल्यूमीनियम ऑक्साइड) c) The structure of the wheel / व्हील की संरचना d) The manufacturer’s symbol / निर्माता का प्रतीक 13. Which of the following is NOT a part of the lathe carriage?13. निम्नलिखित में से कौन सा लेथ कैरिज का हिस्सा नहीं है? a) Saddle / सैडल b) Apron / एप्रन c) Cross-slide / क्रॉस-स्लाइड d) Headstock / हेडस्टॉक 14. To prevent a file from “pinning” (getting clogged), you should:14. एक फाइल को “पिनिंग” (भरने) से रोकने के लिए, आपको चाहिए: a) Apply more pressure / अधिक दाब लगाना b) Use a file card or wire brush to clean it regularly / इसे नियमित रूप से साफ करने के लिए एक फाइल कार्ड या वायर ब्रश का उपयोग करना c) Use oil on the file / फाइल पर तेल का उपयोग करना d) Use a file with finer teeth / महीन दांतों वाली फाइल का उपयोग करना 15. The chuck key should be removed from the chuck before starting the lathe to:15. लेथ शुरू करने से पहले चक से चक की को हटा देना चाहिए ताकि: a) Prevent the workpiece from becoming loose / वर्कपीस को ढीला होने से रोका जा सके b) Prevent it from flying off and causing a serious accident / इसे उड़ने और एक गंभीर दुर्घटना का कारण बनने से रोका जा सके c) Save electricity / बिजली बचाई जा सके d) Keep the key clean / की को साफ रखा जा सके 16. The side clearance angle on a cutting tool:16. एक कटिंग टूल पर साइड क्लीयरेंस एंगल: a) Controls the chip flow / चिप प्रवाह को नियंत्रित करता है b) Prevents the side of the tool from rubbing against the finished surface / टूल के साइड को तैयार सतह से रगड़ने से रोकता है c) Strengthens the tool point / टूल पॉइंट को मजबूत करता है d) Is always zero degrees / हमेशा शून्य डिग्री होता है 17. Which of the following is a non-ferrous metal?17. निम्नलिखित में से कौन सी एक अलौह धातु है? a) Mild Steel / माइल्ड स्टील b) High Carbon Steel / उच्च कार्बन स्टील c) Cast Iron / कच्चा लोहा d) Copper / तांबा 18. A steady rest has:18. एक स्टेडी रेस्ट में होते हैं: a) One adjustable pad / एक समायोज्य पैड b) Two adjustable pads / दो समायोज्य पैड c) Three adjustable pads / तीन समायोज्य पैड d) Four adjustable pads / चार समायोज्य पैड 19. The operation of finishing the end of a workpiece to make it flat and square is:19. एक वर्कपीस के सिरे को समतल और चौकोर बनाने के लिए फिनिशिंग करने का ऑपरेशन है: a) Turning / टर्निंग b) Facing / फेसिंग c) Chamfering / चैम्फरिंग d) Grooving / ग्रूविंग 20. Which material is commonly used for making lathe bed ways?20. लेथ बेड वेज़ बनाने के लिए आमतौर पर किस सामग्री का उपयोग किया जाता है? a) Aluminum / एल्यूमीनियम b) Mild Steel / माइल्ड स्टील c) Cast Iron / कच्चा लोहा d) Brass / पीतल 21. The main scale of a metric micrometer is marked in:21. एक मीट्रिक माइक्रोमीटर का मुख्य पैमाना किसमें चिह्नित होता है: a) Millimeters and half-millimeters / मिलीमीटर और आधे-मिलीमीटर b) Centimeters only / केवल सेंटीमीटर c) Inches and fractions of an inch / इंच और इंच के भिन्न d) Millimeters only / केवल मिलीमीटर 22. Which lathe accessory is required for turning between centers?22. केंद्रों के बीच टर्निंग के लिए किस लेथ एक्सेसरी की आवश्यकता होती है? a) Four-jaw chuck / फोर-जॉ चक b) A lathe dog and drive plate / एक लेथ डॉग और ड्राइव प्लेट c) A collet chuck / एक कोलेट चक d) A steady rest / एक स्टेडी रेस्ट 23. The distance a screw thread advances in one full revolution is called the:23. एक पूर्ण चक्कर में एक स्क्रू थ्रेड द्वारा तय की गई दूरी कहलाती है: a) Pitch / पिच b) Lead / लीड c) Crest / क्रेस्ट d) Root / रूट 24. What happens to steel when it is annealed?24. जब स्टील को एनील किया जाता है तो क्या होता है? a) It becomes harder and more brittle / यह कठोर और अधिक भंगुर हो जाता है b) It becomes softer and more machinable / यह नरम और अधिक मशीनी हो जाता है c) Its color changes permanently / इसका रंग स्थायी रूप से बदल जाता है d) It becomes resistant to rust / यह जंग के प्रतिरोधी हो जाता है 25. A center drill is used to:25. एक सेंटर ड्रिल का उपयोग किया जाता है: a) Drill a large hole quickly / जल्दी से एक बड़ा छेद ड्रिल करने के लिए b) Create a starting point for a twist drill and a seat for a lathe center / एक ट्विस्ट ड्रिल के लिए एक शुरुआती बिंदु बनाने और एक लेथ सेंटर के लिए एक सीट बनाने के लिए c) Cut internal threads / आंतरिक चूड़ियाँ काटने के लिए d) Enlarge an existing hole / एक मौजूदा छेद को बड़ा करने के लिए ← Previous Next → Finish Test / टेस्ट खत्म करें