ITI Turner 1st Year Mock Test – 7 July 16, 2025 ITI Turner 1st Year Mock Test – 7 | Instant Feedback ITI Turner 1st Year Mock Test – 7 आईटीआई टर्नर प्रथम वर्ष मॉक टेस्ट – 7 Time Left: 30:00 Test Complete! 1. The back gear mechanism in a lathe is used to:1. लेथ में बैक गियर तंत्र का उपयोग किया जाता है: a) Increase the spindle speed / स्पिंडल की गति बढ़ाने के लिए b) Reduce the spindle speed and increase torque / स्पिंडल की गति को कम करने और टॉर्क बढ़ाने के लिए c) Cut threads automatically / स्वचालित रूप से चूड़ियाँ काटने के लिए d) Move the tailstock / टेलस्टॉक को हिलाने के लिए 2. A vernier height gauge is used for:2. एक वर्नियर हाइट गेज का उपयोग किया जाता है: a) Measuring the depth of holes / छेदों की गहराई मापने के लिए b) Checking angles / कोणों की जाँच के लिए c) Marking out and measuring vertical heights from a datum surface / एक डेटम सतह से ऊर्ध्वाधर ऊंचाइयों को चिह्नित करने और मापने के लिए d) Measuring the diameter of round bars / गोल छड़ों का व्यास मापने के लिए 3. For a single-start thread, the lead is:3. एक सिंगल-स्टार्ट थ्रेड के लिए, लीड होती है: a) Equal to the pitch / पिच के बराबर b) Double the pitch / पिच से दोगुनी c) Half the pitch / पिच से आधी d) Not related to the pitch / पिच से संबंधित नहीं 4. A lathe dog or carrier is used to:4. एक लेथ डॉग या कैरियर का उपयोग किया जाता है: a) Hold the tool bit / टूल बिट को पकड़ने के लिए b) Drive a workpiece that is held between centers / केंद्रों के बीच पकड़े गए वर्कपीस को चलाने के लिए c) Support a long workpiece / एक लंबे वर्कपीस को सहारा देने के लिए d) Hold irregularly shaped jobs / अनियमित आकार के जॉब को पकड़ने के लिए 5. The heat treatment process that increases hardness but also increases brittleness is:5. वह ऊष्मा उपचार प्रक्रिया जो कठोरता को बढ़ाती है लेकिन भंगुरता को भी बढ़ाती है, वह है: a) Annealing / एनीलिंग b) Normalizing / नॉर्मलाइजिंग c) Hardening / हार्डनिंग d) Tempering / टेम्परिंग 6. To cut an internal thread, the correct sequence of operations is:6. एक आंतरिक चूड़ी काटने के लिए, संचालन का सही क्रम है: a) Tapping, then Drilling / टैपिंग, फिर ड्रिलिंग b) Drilling, then Tapping / ड्रिलिंग, फिर टैपिंग c) Reaming, then Tapping / रीमिंग, फिर टैपिंग d) Boring, then Drilling / बोरिंग, फिर ड्रिलिंग 7. Which of the following is a type of straight-shank grinding wheel?7. निम्नलिखित में से कौन सा एक सीधे-शैंक ग्राइंडिंग व्हील का प्रकार है? a) Flaring cup wheel / फ्लेयरिंग कप व्हील b) Dish wheel / डिश व्हील c) Plain wheel (Type 1) / प्लेन व्हील (टाइप 1) d) Saucer wheel / सॉसर व्हील 8. A sine bar is used in conjunction with slip gauges to accurately measure:8. एक साइन बार का उपयोग स्लिप गेज के साथ सटीक रूप से मापने के लिए किया जाता है: a) Length / लंबाई b) Angles and tapers / कोण और टेपर c) Diameters / व्यास d) Flatness / समतलता 9. The operation of producing a beveled edge on a workpiece is known as:9. एक वर्कपीस पर एक बेवेल्ड किनारा बनाने की प्रक्रिया कहलाती है: a) Grooving / ग्रूविंग b) Knurling / नर्लिंग c) Chamfering / चैम्फरिंग d) Reaming / रीमिंग 10. To prevent injury, a chisel with a “mushroom head” should be:10. चोट से बचने के लिए, एक “मशरूम हेड” वाली छेनी को चाहिए: a) Used with more force / अधिक बल के साथ उपयोग किया जाना चाहिए b) Re-ground to remove the mushroom head before use / उपयोग से पहले मशरूम हेड को हटाने के लिए फिर से ग्राउंड किया जाना चाहिए c) Thrown away immediately / तुरंत फेंक दिया जाना चाहिए d) Used only for soft materials / केवल नरम सामग्री के लिए उपयोग किया जाना चाहिए 11. The main difference between a 3-jaw chuck and a 4-jaw chuck is that the 4-jaw chuck:11. एक 3-जॉ चक और एक 4-जॉ चक के बीच मुख्य अंतर यह है कि 4-जॉ चक: a) Is self-centering / सेल्फ-सेंटरिंग है b) Has jaws that move independently / में जबड़े होते हैं जो स्वतंत्र रूप से चलते हैं c) Can only hold round workpieces / केवल गोल वर्कपीस पकड़ सकता है d) Operates at a higher speed / उच्च गति पर काम करता है 12. Which of these materials has the highest carbon content?12. इनमें से किस सामग्री में सबसे अधिक कार्बन सामग्री है? a) Mild Steel / माइल्ड स्टील b) Wrought Iron / रॉट आयरन c) Cast Iron / कच्चा लोहा d) Aluminum / एल्यूमीनियम 13. A reamer is used to:13. एक रीमर का उपयोग किया जाता है: a) Drill a hole from solid material / ठोस सामग्री से एक छेद ड्रिल करने के लिए b) Finish a hole to a very accurate size and smooth surface / एक छेद को बहुत सटीक आकार और चिकनी सतह तक फिनिश करने के लिए c) Cut internal threads / आंतरिक चूड़ियाँ काटने के लिए d) Enlarge a hole significantly / एक छेद को काफी बड़ा करने के लिए 14. Which part of the lathe provides the powered movement for turning and facing?14. लेथ का कौन सा हिस्सा टर्निंग और फेसिंग के लिए संचालित गति प्रदान करता है? a) Headstock / हेडस्टॉक b) Tailstock / टेलस्टॉक c) Apron mechanism (via feed rod) / एप्रन तंत्र (फ़ीड रॉड के माध्यम से) d) Bed ways / बेड वेज़ 15. The “depth of cut” is:15. “कट की गहराई” है: a) The speed of the workpiece / वर्कपीस की गति b) The thickness of the material removed in one pass / एक पास में हटाई गई सामग्री की मोटाई c) The length of the workpiece / वर्कपीस की लंबाई d) The feed rate of the tool / टूल की फ़ीड दर 16. The correct way to check a measurement with a vernier caliper is to:16. एक वर्नियर कैलिपर से माप की जांच करने का सही तरीका है: a) Read it while it is still on the rotating workpiece / घूमते हुए वर्कपीस पर रहते हुए इसे पढ़ना b) Look at the scale from an angle / पैमाने को एक कोण से देखना c) Look at the scale perpendicularly to avoid parallax error / लंबन त्रुटि से बचने के लिए पैमाने को लंबवत देखना d) Estimate the reading without looking closely / बारीकी से देखे बिना रीडिंग का अनुमान लगाना 17. A half-nut is used to engage the carriage with the:17. एक हाफ-नट का उपयोग कैरिज को किसके साथ संलग्न करने के लिए किया जाता है: a) Feed Rod / फ़ीड रॉड b) Lead Screw / लीड स्क्रू c) Main Spindle / मुख्य स्पिंडल d) Tailstock Quill / टेलस्टॉक क्विल 18. What is the purpose of the graduations on the tailstock body?18. टेलस्टॉक बॉडी पर ग्रेजुएशन का उद्देश्य क्या है? a) To measure the length of the workpiece / वर्कपीस की लंबाई मापने के लिए b) To set the tailstock offset for taper turning / टेपर टर्निंग के लिए टेलस्टॉक ऑफसेट सेट करने के लिए c) To set the spindle speed / स्पिंडल की गति सेट करने के लिए d) To measure the diameter of the workpiece / वर्कपीस का व्यास मापने के लिए 19. In a grinding wheel specification, a letter like ‘K’ would indicate the:19. एक ग्राइंडिंग व्हील विनिर्देश में, ‘K’ जैसा एक अक्षर इंगित करेगा: a) Abrasive type / अपघर्षक प्रकार b) Grain size / ग्रेन का आकार c) Grade (hardness) of the wheel / व्हील का ग्रेड (कठोरता) d) Structure / संरचना 20. The clearance angle is provided on a tool to:20. एक टूल पर क्लीयरेंस एंगल प्रदान किया जाता है: a) Strengthen the cutting edge / कटिंग एज को मजबूत करने के लिए b) Prevent the tool from rubbing against the work / टूल को काम से रगड़ने से रोकने के लिए c) Break the chips / चिप्स को तोड़ने के लिए d) Increase the cutting speed / कटिंग स्पीड बढ़ाने के लिए 21. The property of a metal to resist being stretched or pulled apart is called:21. एक धातु का वह गुण जो उसे खींचे जाने या अलग किए जाने का विरोध करने की अनुमति देता है, कहलाता है: a) Elasticity / लोच b) Tensile strength / तन्यता शक्ति c) Hardness / कठोरता d) Plasticity / प्लास्टिसिटी 22. Which part of the lathe machine supports the main spindle and its driving mechanism?22. लेथ मशीन का कौन सा हिस्सा मुख्य स्पिंडल और उसके ड्राइविंग तंत्र को सहारा देता है? a) Tailstock / टेलस्टॉक b) Bed / बेड c) Carriage / कैरिज d) Headstock / हेडस्टॉक 23. When drilling a deep hole, it is important to:23. एक गहरा छेद ड्रिल करते समय, यह महत्वपूर्ण है: a) Use a very high drilling speed / बहुत उच्च ड्रिलिंग गति का उपयोग करना b) Withdraw the drill frequently to clear chips / चिप्स को साफ करने के लिए ड्रिल को बार-बार वापस लेना c) Use no cutting fluid / कोई कटिंग फ्लुइड का उपयोग नहीं करना d) Apply maximum pressure / अधिकतम दाब लगाना 24. What is the main purpose of a chuck guard?24. एक चक गार्ड का मुख्य उद्देश्य क्या है? a) To protect the operator from flying chips and coolant splash / ऑपरेटर को उड़ते चिप्स और कूलेंट के छींटों से बचाना b) To keep the chuck clean / चक को साफ रखना c) To help in mounting the chuck / चक को माउंट करने में मदद करना d) To cool the chuck / चक को ठंडा करना 25. Taper is expressed as a ratio between the difference in diameters and the:25. टेपर को व्यासों के अंतर और किसके बीच के अनुपात के रूप में व्यक्त किया जाता है: a) Cutting speed / कटिंग स्पीड b) Feed rate / फ़ीड दर c) Length of the taper / टेपर की लंबाई d) Total length of the job / जॉब की कुल लंबाई ← Previous Next → Finish Test / टेस्ट खत्म करें