ITI Turner 1st Year Mock Test – 6 July 16, 2025 ITI Turner 1st Year Mock Test – 6 | Instant Feedback ITI Turner 1st Year Mock Test – 6 आईटीआई टर्नर प्रथम वर्ष मॉक टेस्ट – 6 Time Left: 30:00 Test Complete! 1. In case of a sudden power failure while operating a lathe, what is the first action to take?1. लेथ चलाते समय अचानक बिजली गुल हो जाने की स्थिति में सबसे पहले क्या कार्रवाई करनी चाहिए? a) Try to remove the workpiece / वर्कपीस को हटाने का प्रयास करें b) Wait for the power to return / बिजली वापस आने का इंतजार करें c) Switch off the machine’s main switch immediately / मशीन का मुख्य स्विच तुरंत बंद कर दें d) Call the supervisor / पर्यवेक्षक को बुलाएं 2. The lathe operation of creating a hole in a solid workpiece is called:2. एक ठोस वर्कपीस में छेद बनाने की लेथ प्रक्रिया कहलाती है: a) Boring / बोरिंग b) Reaming / रीमिंग c) Drilling / ड्रिलिंग d) Parting / पार्टिंग 3. A surface gauge is used for:3. एक सरफेस गेज का उपयोग किया जाता है: a) Measuring the depth of a hole / एक छेद की गहराई मापने के लिए b) Checking the flatness of a surface / एक सतह की समतलता की जाँच के लिए c) Scribing lines parallel to a datum edge and checking heights / एक डेटम किनारे के समानांतर रेखाएँ खींचने और ऊंचाइयों की जाँच के लिए d) Measuring angles / कोणों को मापने के लिए 4. A pin punch is used to:4. एक पिन पंच का उपयोग किया जाता है: a) Make a starting mark for a drill / एक ड्रिल के लिए एक शुरुआती निशान बनाने के लिए b) Drive out dowel pins or rivets from holes / छेदों से डॉवेल पिन या रिवेट्स को बाहर निकालने के लिए c) Punch holes in sheet metal / शीट धातु में छेद करने के लिए d) Stamp letters or numbers / अक्षर या संख्याएँ स्टांप करने के लिए 5. To set up the correct gears for threading on a lathe, a turner refers to the:5. लेथ पर थ्रेडिंग के लिए सही गियर सेट करने के लिए, एक टर्नर इसका संदर्भ लेता है: a) Machine’s instruction manual / मशीन का निर्देश मैनुअल b) Thread cutting chart on the machine / मशीन पर थ्रेड कटिंग चार्ट c) Drawing of the workpiece / वर्कपीस का ड्राइंग d) Feed selection lever / फ़ीड चयन लीवर 6. High-carbon steel is often used to make:6. उच्च-कार्बन स्टील का उपयोग अक्सर बनाने के लिए किया जाता है: a) Machine beds / मशीन बेड b) Nuts and bolts / नट और बोल्ट c) Cutting tools like files and chisels / फाइल और छेनी जैसे कटिंग टूल्स d) Car bodies / कार बॉडी 7. Which chuck is best for holding a precision ground rod with maximum concentricity?7. अधिकतम समकेन्द्रता के साथ एक सटीक ग्राउंड रॉड को पकड़ने के लिए कौन सा चक सबसे अच्छा है? a) Three-jaw chuck / थ्री-जॉ चक b) Four-jaw chuck / फोर-जॉ चक c) Collet chuck / कोलेट चक d) Magnetic chuck / मैग्नेटिक चक 8. The ability of a cutting tool to retain its hardness at high temperatures is called:8. एक कटिंग टूल की उच्च तापमान पर अपनी कठोरता बनाए रखने की क्षमता कहलाती है: a) Toughness / टफनेस b) Brittleness / भंगुरता c) Hot hardness / हॉट हार्डनेस d) Malleability / आघातवर्धनीयता 9. The tailstock offset method cannot be used to turn:9. टेलस्टॉक ऑफसेट विधि का उपयोग मोड़ने के लिए नहीं किया जा सकता है: a) External tapers / बाहरी टेपर b) Long, gentle tapers / लंबे, हल्के टेपर c) Internal tapers / आंतरिक टेपर d) Tapers on workpieces held between centers / केंद्रों के बीच पकड़े गए वर्कपीस पर टेपर 10. What is the primary purpose of undercutting (grooving)?10. अंडरकटिंग (ग्रूविंग) का प्राथमिक उद्देश्य क्या है? a) To make the part weaker / हिस्से को कमजोर बनाने के लिए b) To provide clearance for a mating part or a subsequent operation like threading / एक मेल खाने वाले हिस्से या बाद के ऑपरेशन जैसे थ्रेडिंग के लिए क्लीयरेंस प्रदान करना c) To reduce the weight of the part / हिस्से का वजन कम करने के लिए d) To improve the appearance / दिखावट में सुधार करने के लिए 11. “Runout” on a rotating workpiece refers to its:11. एक घूमते हुए वर्कपीस पर “रनआउट” का अर्थ है इसकी: a) Total length / कुल लंबाई b) Rotational speed / घूर्णी गति c) Inaccuracy of rotation (wobble) / घूर्णन की अशुद्धि (डगमगाहट) d) Surface roughness / सतह का खुरदरापन 12. The “apron mechanism” is located on the:12. “एप्रन तंत्र” कहाँ स्थित है: a) Headstock / हेडस्टॉक पर b) Tailstock / टेलस्टॉक पर c) Carriage / कैरिज पर d) Bed / बेड पर 13. For drilling in mild steel, the standard point angle of a twist drill is:13. माइल्ड स्टील में ड्रिलिंग के लिए, एक ट्विस्ट ड्रिल का मानक बिंदु कोण है: a) 90° b) 118° c) 135° d) 60° 14. Normalizing is a heat treatment process done to:14. नॉर्मलाइजिंग एक ऊष्मा उपचार प्रक्रिया है जो की जाती है: a) Make the steel as hard as possible / स्टील को यथासंभव कठोर बनाने के लिए b) Refine the grain structure and relieve internal stresses / ग्रेन संरचना को परिष्कृत करने और आंतरिक तनाव को दूर करने के लिए c) Create a hard surface on a soft core / एक नरम कोर पर एक कठोर सतह बनाने के लिए d) Make the steel very brittle / स्टील को बहुत भंगुर बनाने के लिए 15. A faceplate is used on a lathe to hold:15. एक लेथ पर एक फेसप्लेट का उपयोग पकड़ने के लिए किया जाता है: a) Long, slender workpieces / लंबे, पतले वर्कपीस b) Round bars for quick centering / त्वरित केंद्रण के लिए गोल बार c) Odd-shaped or non-cylindrical workpieces / विषम आकार के या गैर-बेलनाकार वर्कपीस d) Finished parts without marking them / बिना निशान के तैयार हिस्से 16. The two main components of a grinding wheel are the:16. एक ग्राइंडिंग व्हील के दो मुख्य घटक हैं: a) Arbor and flange / आर्बर और फ्लैंज b) Abrasive grains and the bond / अपघर्षक कण और बांड c) Guard and tool rest / गार्ड और टूल रेस्ट d) Wheel and motor / व्हील और मोटर 17. A “chip breaker” on a cutting tool is designed to:17. एक कटिंग टूल पर एक “चिप ब्रेकर” डिज़ाइन किया गया है: a) Make the tool cut faster / टूल को तेजी से काटने के लिए b) Improve the surface finish / सतह फिनिश में सुधार करने के लिए c) Break long, continuous chips into smaller, safer pieces / लंबी, निरंतर चिप्स को छोटे, सुरक्षित टुकड़ों में तोड़ने के लिए d) Cool the cutting tool / कटिंग टूल को ठंडा करने के लिए 18. A dead center is made of hardened steel because:18. एक डेड सेंटर कठोर स्टील का बना होता है क्योंकि: a) It needs to be magnetic / इसे चुंबकीय होने की आवश्यकता है b) It does not rotate and must resist wear from friction / यह घूमता नहीं है और इसे घर्षण से होने वाले घिसाव का विरोध करना चाहिए c) It is cheaper to manufacture / इसका निर्माण सस्ता है d) It rotates with the workpiece / यह वर्कपीस के साथ घूमता है 19. What is the primary purpose of using marking media like layout dye?19. लेआउट डाई जैसे मार्किंग मीडिया का उपयोग करने का प्राथमिक उद्देश्य क्या है? a) To protect the surface from rust / सतह को जंग से बचाने के लिए b) To make scribed lines clearly visible on a metal surface / धातु की सतह पर खींची गई रेखाओं को स्पष्ट रूप से दिखाई देने के लिए c) To lubricate the surface for cutting / काटने के लिए सतह को चिकनाई देने के लिए d) To cool the workpiece / वर्कपीस को ठंडा करने के लिए 20. The time taken for a turning operation can be calculated using:20. एक टर्निंग ऑपरेशन के लिए लिया गया समय का उपयोग करके गणना की जा सकती है: a) Length of cut / (Feed × RPM) / कट की लंबाई / (फ़ीड × RPM) b) (Feed × RPM) / Length of cut / (फ़ीड × RPM) / कट की लंबाई c) Length of cut × Feed × RPM / कट की लंबाई × फ़ीड × RPM d) Diameter × RPM / व्यास × RPM 21. A Class C fire extinguisher is to be used on fires involving:21. एक क्लास C अग्निशामक का उपयोग किस पर लगी आग के लिए किया जाना है: a) Wood, paper, and textiles / लकड़ी, कागज, और वस्त्र b) Flammable liquids like oil and paint / तेल और पेंट जैसे ज्वलनशील तरल पदार्थ c) Live electrical equipment / चालू विद्युत उपकरण d) Combustible metals / ज्वलनशील धातुएं 22. What is the main purpose of a chuck guard on a lathe?22. लेथ पर चक गार्ड का मुख्य उद्देश्य क्या है? a) To keep the chuck clean / चक को साफ रखने के लिए b) To protect the operator from flying chips and coolant / ऑपरेटर को उड़ते चिप्स और कूलेंट से बचाने के लिए c) To help center the workpiece / वर्कपीस को केंद्रित करने में मदद करने के लिए d) To measure the speed of the chuck / चक की गति को मापने के लिए 23. The property of a metal that allows it to resist being pulled apart is:23. एक धातु का वह गुण जो उसे खींचकर अलग किए जाने का विरोध करने की अनुमति देता है, वह है: a) Compressive strength / संपीड़न शक्ति b) Tensile strength / तन्यता शक्ति c) Hardness / कठोरता d) Brittleness / भंगुरता 24. In the specification of a grinding wheel, the “grade” refers to the:24. एक ग्राइंडिंग व्हील के विनिर्देश में, “ग्रेड” संदर्भित करता है: a) Size of the abrasive grains / अपघर्षक कणों का आकार b) Type of abrasive material / अपघर्षक सामग्री का प्रकार c) Hardness or strength of the bond / बांड की कठोरता या मजबूती d) Structure or spacing of the grains / कणों की संरचना या रिक्ति 25. The part of a vernier caliper that slides along the main scale is called the:25. वर्नियर कैलिपर का वह हिस्सा जो मुख्य पैमाने के साथ स्लाइड करता है, कहलाता है: a) Fixed jaw / स्थिर जबड़ा b) Depth bar / गहराई बार c) Vernier scale / वर्नियर स्केल d) Main scale / मुख्य पैमाना ← Previous Next → Finish Test / टेस्ट खत्म करें