ITI Turner 1st Year Mock Test – 5 July 16, 2025 ITI Turner 1st Year Mock Test – 5 | Instant Feedback ITI Turner 1st Year Mock Test – 5 आईटीआई टर्नर प्रथम वर्ष मॉक टेस्ट – 5 Time Left: 30:00 Test Complete! 1. Good workshop housekeeping means:1. अच्छी वर्कशॉप हाउसकीपिंग का मतलब है: a) Cleaning the workshop once a month / महीने में एक बार वर्कशॉप की सफाई करना b) Keeping floors clean, tools organized, and walkways clear / फर्श को साफ रखना, औजारों को व्यवस्थित रखना और रास्तों को साफ रखना c) Painting the walls every year / हर साल दीवारों को पेंट करना d) Having the newest machines / सबसे नई मशीनें रखना 2. Setting the lathe cutting tool slightly below the workpiece center height will:2. लेथ कटिंग टूल को वर्कपीस के केंद्र की ऊंचाई से थोड़ा नीचे सेट करने से: a) Improve the surface finish / सतह की फिनिश में सुधार होगा b) Increase the cutting speed / काटने की गति बढ़ेगी c) Cause incorrect angles and poor cutting action / गलत कोण और खराब कटिंग क्रिया का कारण बनेगा d) Not affect the cutting operation / काटने की प्रक्रिया पर कोई प्रभाव नहीं पड़ेगा 3. The term “Accuracy” in measurement refers to:3. माप में “सटीकता” (Accuracy) शब्द का अर्थ है: a) How close a measurement is to the true value / एक माप वास्तविक मान के कितने करीब है b) How close repeated measurements are to each other / बार-बार किए गए माप एक दूसरे के कितने करीब हैं c) The smallest unit that can be measured / सबसे छोटी इकाई जिसे मापा जा सकता है d) The speed of measurement / माप की गति 4. To prevent rounding the corners of a hexagonal nut, the best tool to use is a:4. एक षट्कोणीय नट के कोनों को गोल होने से बचाने के लिए, उपयोग करने के लिए सबसे अच्छा उपकरण है: a) Adjustable wrench / एडजस्टेबल रिंच b) Open-ended spanner / ओपन-एंडेड स्पैनर c) Ring spanner or a six-point socket / रिंग स्पैनर या सिक्स-पॉइंट सॉकेट d) Pair of pliers / प्लायर्स की एक जोड़ी 5. “Backlash” in the cross-slide screw of a lathe refers to:5. लेथ के क्रॉस-स्लाइड स्क्रू में “बैकलैश” का अर्थ है: a) The total length of the screw / स्क्रू की कुल लंबाई b) The play or lost motion when reversing the handwheel’s direction / हैंडव्हील की दिशा बदलने पर प्ले या खोई हुई गति c) The noise made by the screw / स्क्रू द्वारा किया गया शोर d) The thread pitch of the screw / स्क्रू की थ्रेड पिच 6. The top surface joining the two sides of a screw thread is called the:6. एक स्क्रू थ्रेड के दोनों किनारों को जोड़ने वाली ऊपरी सतह कहलाती है: a) Root / रूट b) Flank / फ्लैंक c) Crest / क्रेस्ट d) Pitch / पिच 7. A simple way to distinguish between ferrous and non-ferrous metals is by using a:7. लौह और अलौह धातुओं के बीच अंतर करने का एक सरल तरीका है, एक का उपयोग करके: a) File / रेती b) Hammer / हथौड़ा c) Magnet / चुंबक d) Micrometer / माइक्रोमीटर 8. For general machining of brass, the recommended cutting fluid is:8. पीतल की सामान्य मशीनिंग के लिए, अनुशंसित कटिंग फ्लुइड है: a) Heavy sulfurized oil / भारी सल्फराइज्ड तेल b) Water / पानी c) No fluid (machined dry) or a light oil / कोई तरल पदार्थ नहीं (सूखा मशीन किया हुआ) या एक हल्का तेल d) Thick grease / मोटी ग्रीस 9. A common cause for a drill bit to break during operation is:9. ऑपरेशन के दौरान एक ड्रिल बिट के टूटने का एक सामान्य कारण है: a) Using a coolant / एक कूलेंट का उपयोग करना b) Running the drill at a very slow speed / ड्रिल को बहुत धीमी गति से चलाना c) A dull drill bit or excessive feed pressure / एक कुंद ड्रिल बिट या अत्यधिक फ़ीड दाब d) Clearing the chips frequently / चिप्स को बार-बार साफ करना 10. The primary purpose of case hardening a steel component is to:10. एक स्टील घटक की केस हार्डनिंग का प्राथमिक उद्देश्य है: a) Make the entire component soft / पूरे घटक को नरम बनाना b) Create a hard, wear-resistant surface with a tough inner core / एक सख्त भीतरी कोर के साथ एक कठोर, घिसाव-प्रतिरोधी सतह बनाना c) Make the component resistant to rust / घटक को जंग के प्रतिरोधी बनाना d) Make the entire component hard and brittle / पूरे घटक को कठोर और भंगुर बनाना 11. “Loading” of a grinding wheel means:11. एक ग्राइंडिंग व्हील की “लोडिंग” का मतलब है: a) The wheel has become smooth and shiny / व्हील चिकना और चमकदार हो गया है b) The wheel pores are clogged with particles of the material being ground / व्हील के छिद्र पीसे जा रहे पदार्थ के कणों से भर गए हैं c) The wheel is perfectly balanced / व्हील पूरी तरह से संतुलित है d) The wheel has been mounted on the machine / व्हील को मशीन पर माउंट किया गया है 12. Before starting work on a lathe, the most important safety check is to ensure:12. लेथ पर काम शुरू करने से पहले, सबसे महत्वपूर्ण सुरक्षा जांच यह सुनिश्चित करना है: a) The machine is well-oiled / मशीन अच्छी तरह से तेल से युक्त है b) The floor around the machine is clean / मशीन के चारों ओर का फर्श साफ है c) The chuck key has been removed from the chuck / चक से चक की को हटा दिया गया है d) The workpiece is painted / वर्कपीस पेंट किया हुआ है 13. The ability of a material to be hammered or rolled into thin sheets is called:13. किसी पदार्थ को पतली चादरों में पीटने या बेलने की क्षमता कहलाती है: a) Ductility / तन्यता b) Hardness / कठोरता c) Malleability / आघातवर्धनीयता d) Toughness / टफनेस 14. A die is a tool used to cut:14. डाई एक उपकरण है जिसका उपयोग काटने के लिए किया जाता है: a) Internal threads / आंतरिक चूड़ियाँ b) External threads / बाहरी चूड़ियाँ c) Flat surfaces / सपाट सतहें d) Keyways / की-वे 15. An excessively high cutting speed on a lathe can cause:15. लेथ पर अत्यधिक उच्च कटिंग स्पीड इसका कारण बन सकती है: a) A better surface finish / एक बेहतर सतह फिनिश b) Rapid wear of the cutting tool / कटिंग टूल का तेजी से घिसना c) The machine to run more quietly / मशीन का अधिक चुपचाप चलना d) Less power consumption / कम बिजली की खपत 16. Tempering is a heat treatment process performed after hardening to:16. टेम्परिंग एक ऊष्मा उपचार प्रक्रिया है जो हार्डनिंग के बाद की जाती है: a) Increase hardness further / कठोरता को और बढ़ाने के लिए b) Reduce brittleness and increase toughness / भंगुरता को कम करने और टफनेस बढ़ाने के लिए c) Make the steel softer / स्टील को नरम बनाने के लिए d) Clean the surface of the steel / स्टील की सतह को साफ करने के लिए 17. Which part of the lathe holds the drill bit for drilling operations?17. लेथ का कौन सा हिस्सा ड्रिलिंग ऑपरेशन के लिए ड्रिल बिट को पकड़ता है? a) Headstock chuck / हेडस्टॉक चक b) Tool post / टूल पोस्ट c) Tailstock / टेलस्टॉक d) Saddle / सैडल 18. A vernier bevel protractor can measure angles with a precision of:18. एक वर्नियर बेवल प्रोट्रैक्टर कोणों को किस सटीकता से माप सकता है: a) 1 degree / 1 डिग्री b) 0.5 degrees / 0.5 डिग्री c) 5 minutes (1/12th of a degree) / 5 मिनट (1/12 डिग्री) d) 1 minute / 1 मिनट 19. In which stroke are the teeth of a file designed to cut?19. एक फाइल के दांत किस स्ट्रोक में काटने के लिए डिज़ाइन किए गए हैं? a) The return stroke / रिटर्न स्ट्रोक में b) The forward stroke / फॉरवर्ड स्ट्रोक में c) Both strokes equally / दोनों स्ट्रोक में समान रूप से d) Only the side strokes / केवल साइड स्ट्रोक में 20. The operation of making a workpiece thinner at one end than the other is called:20. एक वर्कपीस को एक सिरे पर दूसरे से पतला बनाने की प्रक्रिया कहलाती है: a) Step turning / स्टेप टर्निंग b) Taper turning / टेपर टर्निंग c) Facing / फेसिंग d) Boring / बोरिंग 21. A Class D fire involves:21. क्लास D की आग में शामिल हैं: a) Flammable liquids / ज्वलनशील तरल पदार्थ b) Electrical equipment / विद्युत उपकरण c) Combustible metals like magnesium or titanium / मैग्नीशियम या टाइटेनियम जैसी ज्वलनशील धातुएं d) Wood and paper / लकड़ी और कागज 22. What is the main difference between boring and reaming?22. बोरिंग और रीमिंग के बीच मुख्य अंतर क्या है? a) Boring is for external surfaces, reaming is for internal / बोरिंग बाहरी सतहों के लिए है, रीमिंग आंतरिक के लिए है b) Reaming is faster than boring / रीमिंग बोरिंग से तेज है c) Boring can correct a hole’s position, while reaming only sizes an existing hole / बोरिंग एक छेद की स्थिति को ठीक कर सकता है, जबकि रीमिंग केवल एक मौजूदा छेद को आकार देता है d) Reaming removes more material than boring / रीमिंग बोरिंग से अधिक सामग्री हटाता है 23. A four-jaw chuck is also known as a(n):23. एक फोर-जॉ चक को इस रूप में भी जाना जाता है: a) Self-centering chuck / सेल्फ-सेंटरिंग चक b) Universal chuck / यूनिवर्सल चक c) Independent chuck / इंडिपेंडेंट चक d) Collet chuck / कोलेट चक 24. What are the three main parts of a lathe?24. लेथ के तीन मुख्य भाग क्या हैं? a) Chuck, Tool, Motor / चक, टूल, मोटर b) Bed, Headstock, Tailstock / बेड, हेडस्टॉक, टेलस्टॉक c) Carriage, Apron, Saddle / कैरिज, एप्रन, सैडल d) Gears, Levers, Wheels / गियर, लीवर, व्हील्स 25. A tap wrench is used to:25. एक टैप रिंच का उपयोग किया जाता है: a) Hold and turn a die / एक डाई को पकड़ने और घुमाने के लिए b) Hold and turn a tap for cutting internal threads / आंतरिक चूड़ियाँ काटने के लिए एक टैप को पकड़ने और घुमाने के लिए c) Tighten bolts / बोल्ट कसने के लिए d) Hold a drill bit / एक ड्रिल बिट को पकड़ने के लिए ← Previous Next → Finish Test / टेस्ट खत्म करें