ITI MRAC 2nd Year Mock Test – 9 July 16, 2025 ITI MRAC 2nd Year Mock Test – 9 | Instant Feedback ITI MRAC 2nd Year Mock Test – 9 आईटीआई एमआरएसी द्वितीय वर्ष मॉक टेस्ट – 9 Time Left: 30:00 Test Complete! 1. What is a key difference between brazing and welding?1. ब्रेज़िंग और वेल्डिंग के बीच एक मुख्य अंतर क्या है? a) Brazing is hotter than welding / ब्रेज़िंग वेल्डिंग से अधिक गर्म होती है b) In brazing the base metals are not melted, while in welding they are / ब्रेज़िंग में मूल धातुएं नहीं पिघलती हैं, जबकि वेल्डिंग में वे पिघलती हैं c) Welding does not use filler metal / वेल्डिंग में फिलर धातु का उपयोग नहीं होता है d) Brazing can only be used on steel / ब्रेज़िंग का उपयोग केवल स्टील पर किया जा सकता है 2. A slide valve is a component used for capacity control in which type of compressor?2. एक स्लाइड वाल्व एक घटक है जिसका उपयोग किस प्रकार के कंप्रेसर में क्षमता नियंत्रण के लिए किया जाता है? a) Reciprocating compressor / रेसिप्रोकेटिंग कंप्रेसर b) Scroll compressor / स्क्रॉल कंप्रेसर c) Centrifugal compressor / सेंट्रीफ्यूगल कंप्रेसर d) Screw compressor / स्क्रू कंप्रेसर 3. If airflow is noticeably low at all registers in a ducted system, the first thing to check is:3. यदि एक डक्टेड सिस्टम में सभी रजिस्टरों पर वायु प्रवाह स्पष्ट रूप से कम है, तो जांचने वाली पहली चीज है: a) The thermostat setting / थर्मोस्टेट सेटिंग b) The air filter and the blower fan operation / एयर फिल्टर और ब्लोअर पंखे का संचालन c) The refrigerant charge / रेफ्रिजरेंट चार्ज d) The outdoor unit’s cleanliness / आउटडोर इकाई की सफाई 4. In ductwork, Total Pressure is the sum of:4. डक्टवर्क में, कुल दाब किसका योग है: a) Static Pressure and Velocity Pressure / स्थैतिक दाब और वेग दाब b) High Pressure and Low Pressure / उच्च दाब और निम्न दाब c) Absolute Pressure and Gauge Pressure / निरपेक्ष दाब और गेज दाब d) Inlet Pressure and Outlet Pressure / इनलेट दाब और आउटलेट दाब 5. If both the low-side and high-side pressures in a car AC system are very low, this usually indicates:5. यदि एक कार एसी प्रणाली में निम्न-साइड और उच्च-साइड दोनों दाब बहुत कम हैं, तो यह आमतौर पर इंगित करता है: a) A major refrigerant leak or very low charge / एक बड़ा रेफ्रिजरेंट रिसाव या बहुत कम चार्ज b) A refrigerant overcharge / एक रेफ्रिजरेंट ओवरचार्ज c) A blocked condenser / एक अवरुद्ध कंडेनसर d) A faulty compressor / एक खराब कंप्रेसर 6. If a commercial freezer fails to defrost, a possible faulty component is the:6. यदि एक वाणिज्यिक फ्रीजर डीफ्रॉस्ट करने में विफल रहता है, तो एक संभावित दोषपूर्ण घटक है: a) Compressor / कंप्रेसर b) Condenser fan motor / कंडेनसर पंखा मोटर c) Defrost timer, heater, or termination switch / डीफ्रॉस्ट टाइमर, हीटर, या टर्मिनेशन स्विच d) Thermostat / थर्मोस्टेट 7. How is a cartridge fuse tested for continuity?7. एक कार्ट्रिज फ्यूज की कंटिन्यूटी का परीक्षण कैसे किया जाता है? a) By checking its color / इसके रंग की जांच करके b) By shaking it to see if it rattles / इसे हिलाकर देखना कि क्या यह खड़खड़ाता है c) By using a multimeter set to ohms; a good fuse reads near zero / एक मल्टीमीटर को ओम पर सेट करके; एक अच्छा फ्यूज शून्य के करीब पढ़ता है d) By connecting it to a higher voltage / इसे उच्च वोल्टेज से जोड़कर 8. The absorption refrigeration cycle is unique because it uses a heat source instead of a:8. अवशोषण प्रशीतन चक्र अद्वितीय है क्योंकि यह इसके बजाय एक ऊष्मा स्रोत का उपयोग करता है: a) Condenser / कंडेनसर b) Evaporator / इवैपोरेटर c) Mechanical compressor / यांत्रिक कंप्रेसर d) Expansion valve / विस्तार वाल्व 9. A liquid-to-suction heat exchanger is used to:9. एक लिक्विड-टू-सक्शन हीट एक्सचेंजर का उपयोग किया जाता है: a) Mix liquid and suction gases / तरल और सक्शन गैसों को मिलाने के लिए b) Improve system efficiency by subcooling the liquid and superheating the vapor / तरल को सबकूल करके और वाष्प को सुपरहीट करके सिस्टम की दक्षता में सुधार करने के लिए c) Act as a primary filter / एक प्राथमिक फिल्टर के रूप में कार्य करने के लिए d) Separate oil from refrigerant / रेफ्रिजरेंट से तेल अलग करने के लिए 10. What does a “belt drive” fan arrangement allow for, that a direct drive fan does not?10. एक “बेल्ट ड्राइव” पंखा व्यवस्था क्या अनुमति देती है, जो एक डायरेक्ट ड्राइव पंखा नहीं देता है? a) Quieter operation / शांत संचालन b) The ability to easily change fan speed by changing pulley sizes / पुली के आकार को बदलकर पंखे की गति को आसानी से बदलने की क्षमता c) Smaller physical size / छोटा भौतिक आकार d) Less maintenance / कम रखरखाव 11. In a split AC system, the indoor unit is often called the:11. एक स्प्लिट एसी प्रणाली में, इनडोर इकाई को अक्सर कहा जाता है: a) Condensing unit / कंडेंसिंग यूनिट b) Compressor unit / कंप्रेसर यूनिट c) Fan Coil Unit (FCU) or Air Handling Unit (AHU) / फैन कॉइल यूनिट (FCU) या एयर हैंडलिंग यूनिट (AHU) d) Chiller unit / चिलर यूनिट 12. Why is it critical that a refrigeration system is free of moisture?12. यह क्यों महत्वपूर्ण है कि एक प्रशीतन प्रणाली नमी से मुक्त हो? a) Moisture can freeze at the expansion device and form corrosive acids / नमी विस्तार उपकरण पर जम सकती है और संक्षारक अम्ल बना सकती है b) Moisture improves heat transfer / नमी ऊष्मा हस्तांतरण में सुधार करती है c) Moisture makes the refrigerant smell better / नमी रेफ्रिजरेंट को बेहतर महक देती है d) Moisture cannot be removed once it is in the system / एक बार सिस्टम में आ जाने के बाद नमी को हटाया नहीं जा सकता है 13. A “pump down” solenoid valve is typically installed in the:13. एक “पंप डाउन” सोलनॉइड वाल्व आमतौर पर स्थापित किया जाता है: a) Suction line / सक्शन लाइन में b) Discharge line / डिस्चार्ज लाइन में c) Liquid line / लिक्विड लाइन में d) Compressor crankcase / कंप्रेसर क्रैंककेस में 14. What is a common pressure for leak testing a low-pressure side of an R-134a system with nitrogen?14. नाइट्रोजन के साथ R-134a प्रणाली के निम्न-दाब पक्ष का रिसाव परीक्षण करने के लिए एक सामान्य दाब क्या है? a) 500 psi / 500 psi b) 30 psi / 30 psi c) Around 150 psi (but always check manufacturer specs) / लगभग 150 psi (लेकिन हमेशा निर्माता के विनिर्देशों की जांच करें) d) 5 psi / 5 psi 15. What is a Heat Recovery Ventilator (HRV)?15. एक हीट रिकवरी वेंटिलेटर (HRV) क्या है? a) A device that creates heat / एक उपकरण जो गर्मी पैदा करता है b) A device that transfers heat between fresh incoming air and stale exhaust air / एक उपकरण जो ताजी आने वाली हवा और बासी निकास हवा के बीच गर्मी स्थानांतरित करता है c) A type of heat pump / एक प्रकार का हीट पंप d) A fan that recovers lost items from ducts / एक पंखा जो डक्ट से खोई हुई वस्तुओं को पुनः प्राप्त करता है 16. The process of cleaning recovered refrigerant to meet the purity standards of new refrigerant is called:16. नए रेफ्रिजरेंट की शुद्धता के मानकों को पूरा करने के लिए रिकवर किए गए रेफ्रिजरेंट को साफ करने की प्रक्रिया कहलाती है: a) Recycling / रीसाइक्लिंग b) Reclaiming / रिक्लेमिंग c) Recovery / रिकवरी d) Recharging / रिचार्जिंग 17. A PTC (Positive Temperature Coefficient) starter is a type of:17. एक PTC (पॉजिटिव टेम्परेचर कोएफिशिएंट) स्टार्टर एक प्रकार है: a) Potential relay / पोटेंशियल रिले का b) Current relay / करंट रिले का c) Solid-state relay / सॉलिड-स्टेट रिले का d) Time-delay relay / टाइम-डिले रिले का 18. The “R-value” of insulation is a measure of its:18. इन्सुलेशन का “R-मान” इसका एक माप है: a) Resistance to heat flow / ऊष्मा प्रवाह के प्रति प्रतिरोध b) Reflectivity / परावर्तनशीलता c) Density / घनत्व d) Moisture absorption / नमी अवशोषण 19. A “damper” in ductwork is used to:19. डक्टवर्क में एक “डैम्पर” का उपयोग किया जाता है: a) Clean the air / हवा को साफ करने के लिए b) Control or stop airflow / वायु प्रवाह को नियंत्रित करने या रोकने के लिए c) Support the duct / डक्ट को सहारा देने के लिए d) Reduce noise / शोर कम करने के लिए 20. What is a major cause of compressor valve failure?20. कंप्रेसर वाल्व की विफलता का एक प्रमुख कारण क्या है? a) Low ambient temperature / निम्न परिवेश का तापमान b) Liquid refrigerant returning to the compressor (slugging) / कंप्रेसर में तरल रेफ्रिजरेंट का लौटना (स्लगिंग) c) A clean condenser coil / एक साफ कंडेनसर कॉइल d) Correct refrigerant charge / सही रेफ्रिजरेंट चार्ज 21. A “take-off” is a duct fitting that:21. एक “टेक-ऑफ” एक डक्ट फिटिंग है जो: a) Changes the direction of a duct run / एक डक्ट रन की दिशा बदलता है b) Connects a branch duct to a main duct / एक शाखा डक्ट को एक मुख्य डक्ट से जोड़ता है c) Reduces the size of the duct / डक्ट का आकार कम करता है d) Ends a duct run / एक डक्ट रन को समाप्त करता है 22. What is the primary purpose of a cooling tower fill?22. एक कूलिंग टॉवर फिल का प्राथमिक उद्देश्य क्या है? a) To support the tower structure / टॉवर संरचना को सहारा देना b) To filter the water / पानी को फ़िल्टर करना c) To increase the surface area for water and air contact, improving evaporation / पानी और हवा के संपर्क के लिए सतह क्षेत्र बढ़ाना, वाष्पीकरण में सुधार करना d) To store extra water / अतिरिक्त पानी का भंडारण करना 23. If a technician measures zero voltage across a fuse, it means:23. यदि एक तकनीशियन एक फ्यूज के पार शून्य वोल्टेज मापता है, तो इसका मतलब है: a) The fuse is good and the circuit is on / फ्यूज अच्छा है और सर्किट चालू है b) The fuse is blown / फ्यूज उड़ गया है c) There is a short circuit after the fuse / फ्यूज के बाद एक शॉर्ट सर्किट है d) The voltage is too high / वोल्टेज बहुत अधिक है 24. In the context of controls, a “sensor” is a device that:24. नियंत्रणों के संदर्भ में, एक “सेंसर” एक उपकरण है जो: a) Opens a valve or damper / एक वाल्व या डैम्पर खोलता है b) Measures a physical condition (like temperature) and sends a signal / एक भौतिक स्थिति (जैसे तापमान) को मापता है और एक संकेत भेजता है c) Is the main computer of the system / सिस्टम का मुख्य कंप्यूटर है d) Only displays information / केवल जानकारी प्रदर्शित करता है 25. A “VAV” (Variable Air Volume) system controls room temperature primarily by:25. एक “VAV” (वेरिएबल एयर वॉल्यूम) प्रणाली मुख्य रूप से कमरे के तापमान को नियंत्रित करती है: a) Changing the temperature of the supplied air / आपूर्ति की गई हवा का तापमान बदलकर b) Varying the amount of air supplied to the room / कमरे को आपूर्ति की जाने वाली हवा की मात्रा को बदलकर c) Turning the compressor on and off / कंप्रेसर को चालू और बंद करके d) Opening and closing windows / खिड़कियां खोलकर और बंद करके ← Previous Next → Finish Test / टेस्ट खत्म करें