ITI MRAC 2nd Year Mock Test – 8 July 16, 2025 ITI MRAC 2nd Year Mock Test – 8 | Instant Feedback ITI MRAC 2nd Year Mock Test – 8 आईटीआई एमआरएसी द्वितीय वर्ष मॉक टेस्ट – 8 Time Left: 30:00 Test Complete! 1. In ductwork, a fitting used to connect a branch duct to a main trunk duct is called a:1. डक्टवर्क में, एक शाखा डक्ट को एक मुख्य ट्रंक डक्ट से जोड़ने के लिए उपयोग की जाने वाली फिटिंग को कहा जाता है: a) Plenum / प्लेनम b) Elbow / एल्बो c) Take-off / टेक-ऑफ d) Damper / डैम्पर 2. A low refrigerant charge in a water chiller would most likely cause:2. एक वाटर चिलर में कम रेफ्रिजरेंट चार्ज सबसे अधिक संभावना इसका कारण बनेगा: a) High suction pressure and high head pressure / उच्च सक्शन दाब और उच्च हेड प्रेशर b) Low suction pressure and possible freeze-stat trips / निम्न सक्शन दाब और संभावित फ्रीज-स्टैट ट्रिप्स c) The water to become too cold / पानी का बहुत ठंडा हो जाना d) The compressor to run continuously / कंप्रेसर का लगातार चलना 3. The sum of static pressure and velocity pressure in a duct is known as:3. एक डक्ट में स्थैतिक दाब और वेग दाब का योग कहलाता है: a) Gauge pressure / गेज दाब b) Absolute pressure / निरपेक्ष दाब c) Total pressure / कुल दाब d) Differential pressure / विभेदक दाब 4. A major advantage of VRF systems over traditional HVAC systems is:4. पारंपरिक एचवीएसी प्रणालियों की तुलना में VRF प्रणालियों का एक बड़ा लाभ है: a) Lower initial installation cost / कम प्रारंभिक स्थापना लागत b) Simpler controls / सरल नियंत्रण c) Higher energy efficiency and individual zone control / उच्च ऊर्जा दक्षता और व्यक्तिगत क्षेत्र नियंत्रण d) Requires no electricity / कोई बिजली की आवश्यकता नहीं है 5. If a car’s AC compressor clutch is not engaging, the first things to check are:5. यदि कार का एसी कंप्रेसर क्लच नहीं लग रहा है, तो जांचने वाली पहली चीजें हैं: a) The car’s tire pressure / कार के टायर का दाब b) The refrigerant pressure and the electrical circuit (fuse, relay) / रेफ्रिजरेंट दाब और विद्युत सर्किट (फ्यूज, रिले) c) The engine oil level / इंजन तेल का स्तर d) The cabin air filter / केबिन एयर फिल्टर 6. A liquid line solenoid valve is used to:6. एक लिक्विड लाइन सोलनॉइड वाल्व का उपयोग किया जाता है: a) Regulate the pressure in the liquid line / लिक्विड लाइन में दाब को नियंत्रित करना b) Stop the flow of liquid refrigerant, often during a pump down cycle / तरल रेफ्रिजरेंट के प्रवाह को रोकना, अक्सर पंप डाउन चक्र के दौरान c) Filter the refrigerant / रेफ्रिजरेंट को फ़िल्टर करना d) Measure the temperature of the liquid / तरल का तापमान मापना 7. Which of these is a critical factor for heat load calculation?7. इनमें से कौन सा हीट लोड गणना के लिए एक महत्वपूर्ण कारक है? a) The color of the furniture in the room / कमरे में फर्नीचर का रंग b) The R-value of the wall and roof insulation / दीवार और छत के इन्सुलेशन का R-मान c) The brand of the air conditioner to be installed / स्थापित किए जाने वाले एयर कंडीशनर का ब्रांड d) The technician’s years of experience / तकनीशियन के वर्षों का अनुभव 8. The LOTO (Lockout/Tagout) procedure is performed to:8. LOTO (लॉकआउट/टैगआउट) प्रक्रिया की जाती है: a) Lock the doors to the mechanical room / मैकेनिकल रूम के दरवाजे बंद करने के लिए b) Prevent the accidental start-up of equipment during maintenance / रखरखाव के दौरान उपकरणों के आकस्मिक स्टार्ट-अप को रोकने के लिए c) Tag equipment that is working correctly / सही ढंग से काम करने वाले उपकरणों को टैग करने के लिए d) Document the last service date / अंतिम सेवा तिथि का दस्तावेजीकरण करने के लिए 9. An “actuator” in a Building Management System (BMS) is a device that:9. एक बिल्डिंग मैनेजमेंट सिस्टम (BMS) में एक “एक्चुएटर” एक उपकरण है जो: a) Measures temperature or humidity / तापमान या आर्द्रता मापता है b) Receives a control signal and physically moves a component like a damper or valve / एक नियंत्रण संकेत प्राप्त करता है और एक डैम्पर या वाल्व जैसे घटक को भौतिक रूप से हिलाता है c) Displays information on a screen / एक स्क्रीन पर जानकारी प्रदर्शित करता है d) Processes the control logic / नियंत्रण तर्क को संसाधित करता है 10. What is a common material for rigid, rectangular ductwork in commercial buildings?10. वाणिज्यिक भवनों में कठोर, आयताकार डक्टवर्क के लिए एक सामान्य सामग्री क्या है? a) PVC plastic / पीवीसी प्लास्टिक b) Galvanized steel / गैल्वेनाइज्ड स्टील c) Copper / तांबा d) Aluminum foil / एल्यूमीनियम पन्नी 11. An electronic expansion valve (EEV) uses a stepper motor to:11. एक इलेक्ट्रॉनिक विस्तार वाल्व (EEV) एक स्टेपर मोटर का उपयोग करता है: a) Rotate the compressor / कंप्रेसर को घुमाने के लिए b) Precisely control the valve’s opening for refrigerant flow / रेफ्रिजरेंट प्रवाह के लिए वाल्व के उद्घाटन को सटीक रूप से नियंत्रित करने के लिए c) Open and close a solenoid / एक सोलनॉइड को खोलने और बंद करने के लिए d) Drive the condenser fan / कंडेनसर पंखे को चलाने के लिए 12. What is the purpose of the orifice tube in some car AC systems?12. कुछ कार एसी प्रणालियों में ऑर्फिस ट्यूब का उद्देश्य क्या है? a) To store refrigerant / रेफ्रिजरेंट का भंडारण करना b) To filter the refrigerant / रेफ्रिजरेंट को फ़िल्टर करना c) To act as a fixed restriction to meter refrigerant into the evaporator / इवैपोरेटर में रेफ्रिजरेंट को मीटर करने के लिए एक निश्चित प्रतिबंध के रूप में कार्य करना d) To cool the refrigerant / रेफ्रिजरेंट को ठंडा करना 13. In HVAC, a “VAV” box is a component that:13. एचवीएसी में, एक “VAV” बॉक्स एक घटक है जो: a) Varies the voltage to the fan / पंखे को वोल्टेज बदलता है b) Varies the volume of air supplied to a zone / एक क्षेत्र को आपूर्ति की जाने वाली हवा की मात्रा को बदलता है c) Varies the refrigerant flow / रेफ्रिजरेंट प्रवाह को बदलता है d) Verifies air velocity / वायु वेग को सत्यापित करता है 14. What is the first thing a technician should check if a walk-in cooler is not getting cold?14. यदि एक वॉक-इन कूलर ठंडा नहीं हो रहा है तो एक तकनीशियन को सबसे पहले क्या जांचना चाहिए? a) The color of the cooler / कूलर का रंग b) The refrigerant type / रेफ्रिजरेंट का प्रकार c) If the unit has power and the thermostat is set correctly / यदि इकाई में बिजली है और थर्मोस्टेट सही ढंग से सेट है d) The brand of the compressor / कंप्रेसर का ब्रांड 15. A megohmmeter test should be performed only when the:15. एक मेगोहमीटर परीक्षण केवल तभी किया जाना चाहिए जब: a) Equipment is running at full load / उपकरण पूरे लोड पर चल रहा हो b) Equipment is de-energized and disconnected from power / उपकरण डी-एनर्जाइज़्ड और बिजली से डिस्कनेक्ट हो c) Ambient temperature is very high / परिवेश का तापमान बहुत अधिक हो d) Refrigerant charge is low / रेफ्रिजरेंट चार्ज कम हो 16. The purpose of a reversing valve in a heat pump is to:16. एक हीट पंप में एक रिवर्सिंग वाल्व का उद्देश्य है: a) Change the direction of the fan rotation / पंखे के घूमने की दिशा बदलना b) Change the direction of refrigerant flow to switch between heating and cooling / हीटिंग और कूलिंग के बीच स्विच करने के लिए रेफ्रिजरेंट प्रवाह की दिशा बदलना c) Reverse the flow of water / पानी के प्रवाह को उलटना d) Turn the compressor off / कंप्रेसर को बंद करना 17. What is the final step after servicing any refrigeration unit?17. किसी भी प्रशीतन इकाई की सर्विसिंग के बाद अंतिम चरण क्या है? a) Painting the unit / इकाई को पेंट करना b) Overcharging the system slightly / सिस्टम को थोड़ा ओवरचार्ज करना c) A thorough leak check of all disturbed joints / सभी डिस्टर्ब किए गए जोड़ों की पूरी तरह से रिसाव जांच d) Leaving the power off / बिजली बंद छोड़ देना 18. A “hermetic” compressor is different from a “semi-hermetic” one because it:18. एक “हर्मेटिक” कंप्रेसर एक “सेमी-हर्मेटिक” से अलग है क्योंकि यह: a) Is larger / बड़ा है b) Is fully welded and cannot be serviced internally / पूरी तरह से वेल्डेड है और आंतरिक रूप से इसकी सर्विस नहीं की जा सकती c) Is bolted together and can be serviced / एक साथ बोल्ट किया गया है और इसकी सर्विस की जा सकती है d) Runs at a higher speed / उच्च गति पर चलता है 19. In a chilled water system, the AHU contains a:19. एक चिल्ड वाटर सिस्टम में, AHU में होता है: a) Compressor / कंप्रेसर b) Cooling coil through which chilled water flows / एक कूलिंग कॉइल जिसके माध्यम से ठंडा पानी बहता है c) Condenser / कंडेनसर d) Expansion valve / विस्तार वाल्व 20. The purpose of a pump in a hydronic (water-based) HVAC system is to:20. एक हाइड्रोनिक (जल-आधारित) एचवीएसी प्रणाली में एक पंप का उद्देश्य है: a) Circulate the water through the system / सिस्टम के माध्यम से पानी को प्रसारित करना b) Add pressure to the refrigerant / रेफ्रिजरेंट में दाब जोड़ना c) Cool the water / पानी को ठंडा करना d) Filter the water / पानी को फ़िल्टर करना 21. Which refrigerant has zero Ozone Depletion Potential (ODP)?21. किस रेफ्रिजरेंट में शून्य ओजोन क्षरण क्षमता (ODP) है? a) R-12 (CFC) / R-12 (सीएफसी) b) R-22 (HCFC) / R-22 (एचसीएफसी) c) R-134a (HFC) / R-134a (एचएफसी) d) All of the above have some ODP / उपरोक्त सभी में कुछ ODP है 22. A “choked” or restricted filter-drier will show what symptom?22. एक “चोक” या प्रतिबंधित फिल्टर-ड्रायर क्या लक्षण दिखाएगा? a) High pressure on both sides / दोनों तरफ उच्च दाब b) A significant temperature drop across it / इसके पार एक महत्वपूर्ण तापमान गिरावट c) No temperature change across it / इसके पार कोई तापमान परिवर्तन नहीं d) A very loud noise / एक बहुत तेज शोर 23. In the context of controls, a sensor is a device that:23. नियंत्रणों के संदर्भ में, एक सेंसर एक उपकरण है जो: a) Performs an action like opening a valve / वाल्व खोलने जैसी कोई क्रिया करता है b) Measures a physical quantity (like temperature or pressure) and converts it into a signal / एक भौतिक मात्रा (जैसे तापमान या दाब) को मापता है और उसे एक संकेत में परिवर्तित करता है c) Displays information to the user / उपयोगकर्ता को जानकारी प्रदर्शित करता है d) Is the main processor of the system / सिस्टम का मुख्य प्रोसेसर है 24. What is a primary function of the body computer module (BCM) in a modern car’s AC system?24. एक आधुनिक कार के एसी प्रणाली में बॉडी कंप्यूटर मॉड्यूल (BCM) का प्राथमिक कार्य क्या है? a) To compress the refrigerant / रेफ्रिजरेंट को संपीड़ित करना b) To receive inputs from sensors and control the AC compressor clutch and fans / सेंसर से इनपुट प्राप्त करना और एसी कंप्रेसर क्लच और पंखों को नियंत्रित करना c) To cool the air directly / हवा को सीधे ठंडा करना d) To store refrigerant / रेफ्रिजरेंट का भंडारण करना 25. What is the most common method of heat rejection in a split air conditioner?25. एक स्प्लिट एयर कंडीशनर में ऊष्मा अस्वीकृति की सबसे आम विधि क्या है? a) Water-cooled condenser / वाटर-कूल्ड कंडेनसर b) Forced air convection over the outdoor condenser coil / आउटडोर कंडेनसर कॉइल पर बलपूर्वक वायु संवहन c) Evaporative cooling / इवैपोरेटिव कूलिंग d) Geothermal loop / भूतापीय लूप ← Previous Next → Finish Test / टेस्ट खत्म करें