ITI Instrument Mechanic 2nd Year Mock Test – 8 July 18, 2025 ITI Instrument Mechanic 2nd Year Mock Test – 8 | Instant Feedback ITI Instrument Mechanic 2nd Year Mock Test – 8 आईटीआई इंस्ट्रूमेंट मैकेनिक द्वितीय वर्ष मॉक टेस्ट – 8 Time Left: 30:00 Test Complete! 1. The ‘Integral’ action in a PID controller is used to:1. एक PID नियंत्रक में ‘इंटीग्रल’ क्रिया का उपयोग किया जाता है: a) Respond to the rate of change of error / त्रुटि के परिवर्तन की दर पर प्रतिक्रिया करने के लिए b) Eliminate the steady-state error (offset) / स्थिर-अवस्था त्रुटि (ऑफसेट) को खत्म करने के लिए c) Increase the speed of response / प्रतिक्रिया की गति बढ़ाने के लिए d) Reduce the gain of the controller / नियंत्रक के लाभ को कम करने के लिए 2. The part of a PLC that connects to the programming device is the:2. पीएलसी का वह हिस्सा जो प्रोग्रामिंग डिवाइस से जुड़ता है, वह है: a) Input module / इनपुट मॉड्यूल b) Output module / आउटपुट मॉड्यूल c) Communication port / कम्युनिकेशन पोर्ट d) Power supply / बिजली की आपूर्ति 3. A ‘Fail-Safe’ position for a control valve is the position it moves to upon:3. एक कंट्रोल वाल्व के लिए ‘फेल-सेफ’ स्थिति वह स्थिति है जिसमें वह चला जाता है: a) Normal operation / सामान्य संचालन पर b) Manual override / मैनुअल ओवरराइड पर c) Loss of power or air supply / बिजली या हवा की आपूर्ति के नुकसान पर d) Reaching the setpoint / सेटपॉइंट पर पहुंचने पर 4. In calibration, ‘Hysteresis’ is the difference in output for the same input value when:4. अंशांकन में, ‘हिस्टैरिसीस’ एक ही इनपुट मान के लिए आउटपुट में अंतर है जब: a) Approached from opposite directions (upscale and downscale) / विपरीत दिशाओं (अपस्केल और डाउनस्केल) से संपर्क किया जाता है b) Measured at different times / अलग-अलग समय पर मापा जाता है c) The temperature changes / तापमान बदलता है d) The instrument is new / उपकरण नया है 5. A pH of 4 indicates a solution is:5. 4 का pH मान इंगित करता है कि एक घोल है: a) Neutral / उदासीन b) Alkaline / क्षारीय c) Acidic / अम्लीय d) Saturated / संतृप्त 6. The standard voltage signal used in process control instrumentation is:6. प्रोसेस कंट्रोल इंस्ट्रूमेंटेशन में उपयोग किया जाने वाला मानक वोल्टेज सिग्नल है: a) 0-5 V DC / 0-5 V DC b) 1-5 V DC / 1-5 V DC c) 0-10 V DC / 0-10 V DC d) All of the above / उपरोक्त सभी 7. A hydraulic system uses _______ to transmit power.7. एक हाइड्रोलिक प्रणाली शक्ति संचारित करने के लिए _______ का उपयोग करती है। a) Compressed air / संपीड़ित हवा b) Pressurized liquid (oil) / दबावयुक्त तरल (तेल) c) Electricity / बिजली d) Steam / भाप 8. In a control loop, the setpoint (SP) is the:8. एक नियंत्रण लूप में, सेटपॉइंट (SP) है: a) Measured value / मापा गया मान b) Desired value / वांछित मान c) Output value / आउटपुट मान d) Error value / त्रुटि मान 9. A diaphragm valve is suitable for controlling the flow of:9. एक डायाफ्राम वाल्व किसके प्रवाह को नियंत्रित करने के लिए उपयुक्त है: a) High-pressure gases / उच्च दबाव वाली गैसें b) Corrosive fluids and slurries / संक्षारक तरल पदार्थ और स्लरी c) High-temperature steam / उच्च तापमान वाली भाप d) Clean water only / केवल साफ पानी 10. Which system is best for controlling a large, complex industrial process like an oil refinery?10. एक तेल रिफाइनरी जैसी बड़ी, जटिल औद्योगिक प्रक्रिया को नियंत्रित करने के लिए कौन सी प्रणाली सबसे अच्छी है? a) A single PLC / एक एकल पीएलसी b) A microcontroller / एक माइक्रोकंट्रोलर c) A Distributed Control System (DCS) / एक डिस्ट्रिब्यूटेड कंट्रोल सिस्टम (DCS) d) A set of relays / रिले का एक सेट 11. A ‘solenoid valve’ is operated by:11. एक ‘सोलनॉइड वाल्व’ किसके द्वारा संचालित होता है: a) An electric current / एक विद्युत धारा b) Pneumatic pressure / वायवीय दबाव c) Hydraulic pressure / हाइड्रोलिक दबाव d) Manual lever / एक मैनुअल लीवर 12. The zero point of the Kelvin temperature scale is:12. केल्विन तापमान पैमाने का शून्य बिंदु है: a) The freezing point of water / पानी का हिमांक b) The boiling point of water / पानी का क्वथनांक c) Absolute Zero / परम शून्य d) Same as 0°C / 0°C के समान 13. The purpose of a filter in a pneumatic system is to:13. एक वायवीय प्रणाली में एक फिल्टर का उद्देश्य है: a) Increase the air pressure / वायु दाब बढ़ाना b) Remove contaminants like dust and water from the air / हवा से धूल और पानी जैसे दूषित पदार्थों को हटाना c) Add oil to the air / हवा में तेल मिलाना d) Cool the air / हवा को ठंडा करना 14. What is the most important personal quality for an instrument mechanic?14. एक इंस्ट्रूमेंट मैकेनिक के लिए सबसे महत्वपूर्ण व्यक्तिगत गुण क्या है? a) Great physical strength / महान शारीरिक शक्ति b) Speed of work / काम की गति c) A logical approach to troubleshooting and attention to detail / समस्या निवारण और विस्तार पर ध्यान देने के लिए एक तार्किक दृष्टिकोण d) Ability to work alone / अकेले काम करने की क्षमता 15. A PLC is an industrial computer used for:15. एक पीएलसी एक औद्योगिक कंप्यूटर है जिसका उपयोग किया जाता है: a) Web Browse / वेब ब्राउज़िंग के लिए b) Automation of industrial processes / औद्योगिक प्रक्रियाओं के स्वचालन के लिए c) Word processing / वर्ड प्रोसेसिंग के लिए d) Graphic design / ग्राफिक डिजाइन के लिए 16. The ‘proportional band’ in a controller is:16. एक नियंत्रक में ‘प्रोपोर्शनल बैंड’ है: a) Inversely proportional to the gain / गेन के व्युत्क्रमानुपाती b) Directly proportional to the gain / गेन के सीधे आनुपातिक c) Equal to the gain / गेन के बराबर d) Not related to the gain / गेन से संबंधित नहीं 17. A valve used for precise flow control is a:17. सटीक प्रवाह नियंत्रण के लिए उपयोग किया जाने वाला एक वाल्व है: a) Gate valve / गेट वाल्व b) Ball valve / बॉल वाल्व c) Needle valve / नीडल वाल्व d) Check valve / चेक वाल्व 18. A ‘microcontroller’ is essentially a:18. एक ‘माइक्रोकंट्रोलर’ अनिवार्य रूप से है: a) Small computer on a single chip / एक ही चिप पर एक छोटा कंप्यूटर b) A large mainframe computer / एक बड़ा मेनफ्रेम कंप्यूटर c) A type of sensor / एक प्रकार का सेंसर d) A type of memory / एक प्रकार की मेमोरी 19. In a control system, the element that measures the process variable is the:19. एक नियंत्रण प्रणाली में, वह तत्व जो प्रक्रिया चर को मापता है, वह है: a) Controller / नियंत्रक b) Final control element / अंतिम नियंत्रण तत्व c) Sensor / सेंसर d) Actuator / एक्चुएटर 20. What does SCADA stand for?20. स्काडा (SCADA) का क्या अर्थ है? a) Supervisory Control And Data Acquisition / सुपरवाइजरी कंट्रोल एंड डेटा एक्विजिशन b) System Control And Data Access / सिस्टम कंट्रोल एंड डेटा एक्सेस c) Signal Conditioning And Digital Analysis / सिग्नल कंडीशनिंग एंड डिजिटल एनालिसिस d) Supervisory Computer And Data Automation / सुपरवाइजरी कंप्यूटर एंड डेटा ऑटोमेशन 21. The purpose of a ‘positioner’ on a control valve is to:21. एक कंट्रोल वाल्व पर ‘पोजिशनर’ का उद्देश्य है: a) Accurately position the valve stem according to the controller’s signal / नियंत्रक के संकेत के अनुसार वाल्व स्टेम को सटीक रूप से स्थिति में लाना b) Open and close the valve manually / वाल्व को मैन्युअल रूप से खोलना और बंद करना c) Measure the flow through the valve / वाल्व के माध्यम से प्रवाह को मापना d) Increase the pressure of the fluid / तरल पदार्थ का दबाव बढ़ाना 22. Which safety device protects a circuit from overcurrent?22. कौन सा सुरक्षा उपकरण एक सर्किट को ओवरकरंट से बचाता है? a) A switch / एक स्विच b) A resistor / एक अवरोधक c) A fuse or circuit breaker / एक फ्यूज या सर्किट ब्रेकर d) A capacitor / एक कैपेसिटर 23. In a PLC, the input module is used to:23. एक पीएलसी में, इनपुट मॉड्यूल का उपयोग किया जाता है: a) Execute the program / प्रोग्राम को निष्पादित करना b) Receive signals from field devices like sensors / सेंसर जैसे फील्ड उपकरणों से संकेत प्राप्त करना c) Send signals to actuators / एक्चुएटर्स को संकेत भेजना d) Store the program / प्रोग्राम को स्टोर करना 24. A PID controller provides _______ control.24. एक PID नियंत्रक _______ नियंत्रण प्रदान करता है। a) On-off / ऑन-ऑफ b) Proportional, Integral, and Derivative / प्रोपोर्शनल, इंटीग्रल, और डेरिवेटिव c) Open-loop / ओपन-लूप d) Digital only / केवल डिजिटल 25. A key safety principle is to always _______ before working on electrical equipment.25. एक प्रमुख सुरक्षा सिद्धांत है कि विद्युत उपकरणों पर काम करने से पहले हमेशा _______। a) De-energize and lockout the power source / बिजली के स्रोत को डी-एनर्जाइज और लॉकआउट करें b) Wear wet gloves / गीले दस्ताने पहनें c) Stand on a metal floor / धातु के फर्श पर खड़े हों d) Use a metal ladder / एक धातु की सीढ़ी का उपयोग करें ← Previous Next → Finish Test / टेस्ट खत्म करें