ITI Instrument Mechanic 2nd Year Mock Test – 7 July 18, 2025 ITI Instrument Mechanic 2nd Year Mock Test – 7 | Instant Feedback ITI Instrument Mechanic 2nd Year Mock Test – 7 आईटीआई इंस्ट्रूमेंट मैकेनिक द्वितीय वर्ष मॉक टेस्ट – 7 Time Left: 30:00 Test Complete! 1. The purpose of a ‘cascade control’ system is to:1. ‘कैस्केड कंट्रोल’ प्रणाली का उद्देश्य है: a) Control two variables with one controller / एक नियंत्रक से दो चरों को नियंत्रित करना b) Use a primary (master) controller to adjust the setpoint of a secondary (slave) controller / एक द्वितीयक (स्लेव) नियंत्रक के सेटपॉइंट को समायोजित करने के लिए एक प्राथमिक (मास्टर) नियंत्रक का उपयोग करना c) Switch between two different controllers / दो अलग-अलग नियंत्रकों के बीच स्विच करना d) Control only one variable / केवल एक चर को नियंत्रित करना 2. A ‘Fail-Open’ valve will _______ on loss of control signal.2. एक ‘फेल-ओपन’ वाल्व नियंत्रण संकेत के नुकसान पर _______। a) Close / बंद हो जाएगा b) Open / खुल जाएगा c) Stay in its last position / अपनी अंतिम स्थिति में रहेगा d) Vibrate / कंपन करेगा 3. The programming language for PLCs that resembles a series of electrical relay circuits is:3. पीएलसी के लिए प्रोग्रामिंग भाषा जो विद्युत रिले सर्किट की एक श्रृंखला से मिलती-जुलती है, वह है: a) Structured Text / स्ट्रक्चर्ड टेक्स्ट b) Function Block Diagram / फंक्शन ब्लॉक डायग्राम c) Ladder Logic / लैडर लॉजिक d) C++ / सी++ 4. An ORP sensor is used to measure:4. एक ORP सेंसर का उपयोग मापने के लिए किया जाता है: a) pH of a solution / एक घोल का पीएच b) Oxidation-Reduction Potential of a solution / एक घोल का ऑक्सीकरण-अपचयन विभव c) Temperature of a solution / एक घोल का तापमान d) Conductivity of a solution / एक घोल की चालकता 5. What does DCS stand for in process control?5. प्रोसेस कंट्रोल में डीसीएस का क्या अर्थ है? a) Digital Control System / डिजिटल कंट्रोल सिस्टम b) Direct Control System / डायरेक्ट कंट्रोल सिस्टम c) Distributed Control System / डिस्ट्रिब्यूटेड कंट्रोल सिस्टम d) Data Control Station / डेटा कंट्रोल स्टेशन 6. The final control element in a temperature control loop is often a:6. एक तापमान नियंत्रण लूप में अंतिम नियंत्रण तत्व अक्सर होता है: a) Thermocouple / थर्मोकपल b) Control valve or Heater / कंट्रोल वाल्व या हीटर c) Temperature transmitter / तापमान ट्रांसमीटर d) Temperature gauge / तापमान गेज 7. A pneumatic actuator converts:7. एक वायवीय एक्चुएटर परिवर्तित करता है: a) Electrical energy into motion / विद्युत ऊर्जा को गति में b) Compressed air energy into mechanical motion / संपीड़ित वायु ऊर्जा को यांत्रिक गति में c) Hydraulic energy into motion / हाइड्रोलिक ऊर्जा को गति में d) Motion into an electrical signal / गति को एक विद्युत संकेत में 8. The process variable (PV) is the:8. प्रक्रिया चर (PV) है: a) Desired value / वांछित मान b) The actual measured value of the quantity being controlled / नियंत्रित की जा रही मात्रा का वास्तविक मापा गया मान c) The controller’s output / नियंत्रक का आउटपुट d) The error signal / त्रुटि संकेत 9. An I/P converter is used to convert:9. एक I/P कनवर्टर का उपयोग परिवर्तित करने के लिए किया जाता है: a) A current signal to a pressure signal / एक करंट सिग्नल को एक प्रेशर सिग्नल में b) A pressure signal to a current signal / एक प्रेशर सिग्नल को एक करंट सिग्नल में c) An analog signal to a digital signal / एक एनालॉग सिग्नल को एक डिजिटल सिग्नल में d) A digital signal to an analog signal / एक डिजिटल सिग्नल को एक एनालॉग सिग्नल में 10. What is the most important safety rule when working on a high-pressure system?10. उच्च दबाव प्रणाली पर काम करते समय सबसे महत्वपूर्ण सुरक्षा नियम क्या है? a) Isolate and depressurize the system before starting work / काम शुरू करने से पहले सिस्टम को अलग और दबाव रहित करें b) Wear loose clothing / ढीले कपड़े पहनें c) Work alone / अकेले काम करें d) Use damaged tools / क्षतिग्रस्त उपकरणों का उपयोग करें 11. A ‘globe valve’ is best suited for:11. एक ‘ग्लोब वाल्व’ सबसे उपयुक्त है: a) On-off control / ऑन-ऑफ नियंत्रण के लिए b) Throttling or regulating flow / थ्रॉटलिंग या प्रवाह को विनियमित करने के लिए c) Handling slurries / स्लरी को संभालने के लिए d) High flow with low pressure drop / कम दबाव ड्रॉप के साथ उच्च प्रवाह के लिए 12. A PLC is a type of:12. एक पीएलसी एक प्रकार है: a) Sensor / सेंसर का b) Actuator / एक्चुएटर का c) Industrial computer for control / नियंत्रण के लिए एक औद्योगिक कंप्यूटर का d) Measuring instrument / मापने वाले उपकरण का 13. The main function of an Op-Amp is:13. एक Op-Amp का मुख्य कार्य है: a) To amplify signals / संकेतों को बढ़ाना b) To store data / डेटा संग्रहीत करना c) To convert AC to DC / AC को DC में बदलना d) To generate power / शक्ति उत्पन्न करना 14. What does the term “tuning” refer to in a PID controller?14. एक PID नियंत्रक में “ट्यूनिंग” शब्द का क्या अर्थ है? a) Adjusting the P, I, and D parameters for optimal control / इष्टतम नियंत्रण के लिए P, I, और D मापदंडों को समायोजित करना b) Changing the setpoint / सेटपॉइंट बदलना c) Calibrating the sensor / सेंसर को कैलिब्रेट करना d) Cleaning the controller / नियंत्रक को साफ करना 15. A microcontroller contains a CPU, memory, and:15. एक माइक्रोकंट्रोलर में एक सीपीयू, मेमोरी और होता है: a) A large screen / एक बड़ी स्क्रीन b) A keyboard / एक कीबोर्ड c) Input/Output peripherals on a single chip / एक ही चिप पर इनपुट/आउटपुट पेरिफेरल्स d) A hard drive / एक हार्ड ड्राइव 16. The final element in a control loop that directly affects the process is the:16. एक नियंत्रण लूप में अंतिम तत्व जो सीधे प्रक्रिया को प्रभावित करता है, वह है: a) Sensor / सेंसर b) Controller / नियंत्रक c) Final Control Element / अंतिम नियंत्रण तत्व d) Transmitter / ट्रांसमीटर 17. An ‘Air-to-Close’ valve needs air pressure to:17. एक ‘एयर-टू-क्लोज’ वाल्व को हवा के दबाव की आवश्यकता होती है: a) Open / खुलने के लिए b) Close / बंद होने के लिए c) Stay in position / स्थिति में रहने के लिए d) Regulate / विनियमित करने के लिए 18. The process of converting an analog signal to a digital signal is done by a(n):18. एक एनालॉग सिग्नल को एक डिजिटल सिग्नल में परिवर्तित करने की प्रक्रिया किसके द्वारा की जाती है: a) DAC / डीएसी b) ADC / एडीसी c) PLC / पीएलसी d) Op-Amp / Op-Amp 19. A ‘Permit-to-Work’ system is a formal procedure to ensure:19. एक ‘परमिट-टू-वर्क’ प्रणाली यह सुनिश्चित करने के लिए एक औपचारिक प्रक्रिया है: a) Work is done quickly / काम जल्दी से किया जाता है b) That potentially hazardous jobs are done safely / कि संभावित रूप से खतरनाक काम सुरक्षित रूप से किए जाते हैं c) Only senior workers perform the job / केवल वरिष्ठ कर्मचारी ही काम करते हैं d) The work is documented / काम का दस्तावेजीकरण किया जाता है 20. Which sensor is used for non-contact measurement of level?20. स्तर के गैर-संपर्क माप के लिए कौन सा सेंसर उपयोग किया जाता है? a) DP transmitter / डीपी ट्रांसमीटर b) Float switch / फ्लोट स्विच c) Ultrasonic or Radar level sensor / अल्ट्रासोनिक या रडार लेवल सेंसर d) Sight glass / साइट ग्लास 21. The main purpose of a control valve positioner is to:21. एक कंट्रोल वाल्व पोजिशनर का मुख्य उद्देश्य है: a) Increase the pressure to the valve / वाल्व पर दबाव बढ़ाना b) Ensure the valve stem moves to the exact position required by the controller / यह सुनिश्चित करना कि वाल्व स्टेम नियंत्रक द्वारा आवश्यक सटीक स्थिति में चला जाए c) Act as a manual override / एक मैनुअल ओवरराइड के रूप में कार्य करना d) Measure the flow through the valve / वाल्व के माध्यम से प्रवाह को मापना 22. Which part of a PLC stores the user-written program?22. एक पीएलसी का कौन सा हिस्सा यूजर-लिखित प्रोग्राम को संग्रहीत करता है? a) CPU / सीपीयू b) Memory (RAM or EEPROM) / मेमोरी (रैम या EEPROM) c) Input Module / इनपुट मॉड्यूल d) Output Module / आउटपुट मॉड्यूल 23. In a process control system, the “feedback” is the signal from the:23. एक प्रोसेस कंट्रोल सिस्टम में, “फीडबैक” किससे आने वाला सिग्नल है: a) Controller to the actuator / नियंत्रक से एक्चुएटर तक b) Sensor/Transmitter to the controller / सेंसर/ट्रांसमीटर से नियंत्रक तक c) Actuator to the final control element / एक्चुएटर से अंतिम नियंत्रण तत्व तक d) Setpoint to the controller / सेटपॉइंट से नियंत्रक तक 24. What is a key safety practice when working on a hydraulic system?24. एक हाइड्रोलिक प्रणाली पर काम करते समय एक प्रमुख सुरक्षा अभ्यास क्या है? a) Check for leaks with your bare hands / अपने नंगे हाथों से लीक की जांच करना b) Release stored hydraulic pressure before starting work / काम शुरू करने से पहले संग्रहीत हाइड्रोलिक दबाव को छोड़ना c) Tighten fittings while the system is under pressure / सिस्टम दबाव में होने पर फिटिंग को कसना d) Use any type of oil in the system / सिस्टम में किसी भी प्रकार के तेल का उपयोग करना 25. A controller that takes the error, its integral, and its derivative into account is a:25. एक नियंत्रक जो त्रुटि, उसके इंटीग्रल और उसके डेरिवेटिव को ध्यान में रखता है, वह है: a) P controller / P नियंत्रक b) PI controller / PI नियंत्रक c) PD controller / PD नियंत्रक d) PID controller / PID नियंत्रक ← Previous Next → Finish Test / टेस्ट खत्म करें