ITI Instrument Mechanic 2nd Year Mock Test – 2 July 18, 2025 ITI Instrument Mechanic 2nd Year Mock Test – 2 | Instant Feedback ITI Instrument Mechanic 2nd Year Mock Test – 2 आईटीआई इंस्ट्रूमेंट मैकेनिक द्वितीय वर्ष मॉक टेस्ट – 2 Time Left: 30:00 Test Complete! 1. A control system that does not have a feedback loop is called a(n):1. एक नियंत्रण प्रणाली जिसमें फीडबैक लूप नहीं होता है, कहलाती है: a) Closed-loop system / क्लोज्ड-लूप सिस्टम b) Open-loop system / ओपन-लूप सिस्टम c) Feedback system / फीडबैक सिस्टम d) Automatic system / स्वचालित सिस्टम 2. The part of a PLC that connects to sensors and switches is the:2. पीएलसी का वह हिस्सा जो सेंसर और स्विच से जुड़ता है, वह है: a) CPU / सीपीयू b) Output Module / आउटपुट मॉड्यूल c) Input Module / इनपुट मॉड्यूल d) Power Supply / बिजली की आपूर्ति 3. The device that physically moves a control valve stem is the:3. वह उपकरण जो एक नियंत्रण वाल्व के स्टेम को भौतिक रूप से हिलाता है, वह है: a) Positioner / पोजिशनर b) Controller / नियंत्रक c) Actuator / एक्चुएटर d) Sensor / सेंसर 4. The process of adjusting an instrument’s lowest reading to match a known low value is:4. एक उपकरण की सबसे कम रीडिंग को एक ज्ञात निम्न मान से मिलाने के लिए समायोजित करने की प्रक्रिया है: a) Span adjustment / स्पैन समायोजन b) Zero adjustment / शून्य समायोजन c) Range adjustment / रेंज समायोजन d) Linearity adjustment / रैखिकता समायोजन 5. A pH meter is used to measure the:5. एक पीएच मीटर का उपयोग मापने के लिए किया जाता है: a) Conductivity of a solution / एक घोल की चालकता b) Acidity or alkalinity of a solution / एक घोल की अम्लता या क्षारीयता c) Temperature of a solution / एक घोल का तापमान d) Density of a solution / एक घोल का घनत्व 6. The 4-20 mA signal is preferred over a 0-20 mA signal because:6. 0-20 mA सिग्नल की तुलना में 4-20 mA सिग्नल को प्राथमिकता दी जाती है क्योंकि: a) It uses less power / यह कम बिजली का उपयोग करता है b) It can distinguish between a zero reading and a broken wire / यह एक शून्य रीडिंग और एक टूटे हुए तार के बीच अंतर कर सकता है c) It is faster / यह तेज है d) It is an older standard / यह एक पुराना मानक है 7. The device that supplies compressed air to a pneumatic system is the:7. एक वायवीय प्रणाली को संपीड़ित हवा की आपूर्ति करने वाला उपकरण है: a) Hydraulic pump / हाइड्रोलिक पंप b) Air compressor / एयर कंप्रेसर c) Actuator / एक्चुएटर d) Reservoir / जलाशय 8. In a control loop, the desired value for a process variable is the:8. एक नियंत्रण लूप में, एक प्रक्रिया चर के लिए वांछित मान है: a) Process Variable (PV) / प्रोसेस वेरिएबल (PV) b) Setpoint (SP) / सेटपॉइंट (SP) c) Manipulated Variable (MV) / मैनिपुलेटेड वेरिएबल (MV) d) Error (E) / एरर (E) 9. A diaphragm seal is used with a pressure transmitter to:9. एक प्रेशर ट्रांसमीटर के साथ एक डायाफ्राम सील का उपयोग किया जाता है: a) Increase the pressure / दबाव बढ़ाने के लिए b) Isolate the transmitter from corrosive or viscous process fluids / ट्रांसमीटर को संक्षारक या चिपचिपे प्रक्रिया तरल पदार्थों से अलग करने के लिए c) Measure temperature instead of pressure / दबाव के बजाय तापमान मापने के लिए d) Amplify the signal / सिग्नल को बढ़ाने के लिए 10. Which system is typically used for controlling an entire plant-wide process?10. कौन सी प्रणाली आमतौर पर एक पूरे संयंत्र-व्यापी प्रक्रिया को नियंत्रित करने के लिए उपयोग की जाती है? a) PLC (Programmable Logic Controller) / पीएलसी b) DCS (Distributed Control System) / डीसीएस c) Microcontroller / माइक्रोकंट्रोलर d) SCADA / स्काडा 11. A device that ensures a valve reaches the exact position dictated by the controller is a:11. एक उपकरण जो यह सुनिश्चित करता है कि एक वाल्व नियंत्रक द्वारा निर्धारित सटीक स्थिति तक पहुँचे, वह है: a) Actuator / एक्चुएटर b) Sensor / सेंसर c) Positioner / पोजिशनर d) Transmitter / ट्रांसमीटर 12. The difference between the highest and lowest value an instrument is calibrated to measure is its:12. एक उपकरण द्वारा मापने के लिए अंशांकित उच्चतम और निम्नतम मान के बीच का अंतर है: a) Range / रेंज b) Span / स्पैन c) Zero / शून्य d) Accuracy / सटीकता 13. Conductivity is a measure of a solution’s ability to:13. चालकता एक घोल की क्षमता का एक माप है: a) Resist heat / गर्मी का विरोध करना b) Conduct electricity / बिजली का संचालन करना c) Change color / रंग बदलना d) Absorb light / प्रकाश को अवशोषित करना 14. The component that converts pneumatic energy into linear motion is a:14. वह घटक जो वायवीय ऊर्जा को रैखिक गति में परिवर्तित करता है, वह है: a) Compressor / कंप्रेसर b) Valve / वाल्व c) Cylinder / सिलेंडर d) Regulator / रेगुलेटर 15. The element that directly manipulates the process (e.g., a valve) is the:15. वह तत्व जो सीधे प्रक्रिया में हेरफेर करता है (जैसे, एक वाल्व), वह है: a) Sensor / सेंसर b) Controller / नियंत्रक c) Final control element / अंतिम नियंत्रण तत्व d) Transmitter / ट्रांसमीटर 16. What does LOTO stand for in industrial safety?16. औद्योगिक सुरक्षा में LOTO का क्या अर्थ है? a) Look Out, Turn Off / देखो, बंद करो b) Lockout/Tagout / लॉकआउट/टैगआउट c) Lights On, Tools Off / लाइट ऑन, टूल्स ऑफ d) Low Oxygen, Take Out / कम ऑक्सीजन, बाहर निकालो 17. A DP (Differential Pressure) transmitter can be used to measure the _______ in a tank.17. एक डीपी (डिफरेंशियल प्रेशर) ट्रांसमीटर का उपयोग एक टैंक में _______ को मापने के लिए किया जा सकता है। a) Temperature / तापमान b) Level / स्तर c) pH / पीएच d) Viscosity / श्यानता 18. An “Air-to-Open” valve will:18. एक “एयर-टू-ओपन” वाल्व: a) Close when air pressure is applied / हवा का दबाव लागू होने पर बंद हो जाएगा b) Open when air pressure is applied / हवा का दबाव लागू होने पर खुल जाएगा c) Remain in its last position on air failure / हवा की विफलता पर अपनी अंतिम स्थिति में रहेगा d) Does not use air / हवा का उपयोग नहीं करता है 19. An Operational Amplifier (Op-Amp) is a key component in:19. एक ऑपरेशनल एम्पलीफायर (Op-Amp) किसका एक प्रमुख घटक है: a) Power supplies / बिजली की आपूर्ति b) Signal conditioning circuits / सिग्नल कंडीशनिंग सर्किट c) Digital logic circuits / डिजिटल लॉजिक सर्किट d) Pneumatic systems / वायवीय प्रणाली 20. The symbol of a circle with a triangle inside pointing outwards represents a:20. एक त्रिभुज के साथ एक वृत्त का प्रतीक जो बाहर की ओर इशारा करता है, दर्शाता है: a) Valve / एक वाल्व b) Pump / एक पंप c) Compressor (source of compressed air) / एक कंप्रेसर (संपीड़ित हवा का स्रोत) d) Motor / एक मोटर 21. In a feedback control system, the difference between the setpoint and the process variable is the:21. एक फीडबैक नियंत्रण प्रणाली में, सेटपॉइंट और प्रक्रिया चर के बीच का अंतर है: a) Output / आउटपुट b) Error or Deviation / एरर या डेविएशन c) Gain / गेन d) Feedback signal / फीडबैक सिग्नल 22. Before working on any instrument in a process line, you must first:22. एक प्रोसेस लाइन में किसी भी उपकरण पर काम करने से पहले, आपको सबसे पहले चाहिए: a) Clean it / इसे साफ करें b) Check its calibration / इसका अंशांकन जांचें c) Isolate it from the process and depressurize it / इसे प्रक्रिया से अलग करें और इसका दबाव कम करें d) Check its wiring / इसकी वायरिंग जांचें 23. The ‘4 mA’ value in a 4-20 mA signal is known as the:23. 4-20 mA सिग्नल में ‘4 mA’ मान को कहा जाता है: a) Dead zero / डेड जीरो b) Live zero / लाइव जीरो c) Span / स्पैन d) Range / रेंज 24. A PLC is primarily used for:24. एक पीएलसी का उपयोग मुख्य रूप से किया जाता है: a) Complex mathematical calculations / जटिल गणितीय गणनाओं के लिए b) Industrial automation and control / औद्योगिक स्वचालन और नियंत्रण के लिए c) Data storage / डेटा भंडारण के लिए d) Web Browse / वेब ब्राउज़िंग के लिए 25. What is the most common safety hazard in a process plant?25. एक प्रोसेस प्लांट में सबसे आम सुरक्षा खतरा क्या है? a) High pressure / उच्च दबाव b) High temperature / उच्च तापमान c) Hazardous chemicals / खतरनाक रसायन d) All of the above / उपरोक्त सभी ← Previous Next → Finish Test / टेस्ट खत्म करें