ITI Welder 1st Year Mock Test – 1 July 19, 2025 ITI Welder 1st Year Mock Test – 1 | Instant Feedback ITI Welder 1st Year Mock Test – 1 आईटीआई वेल्डर प्रथम वर्ष मॉक टेस्ट – 1 Time Left: 30:00 Test Complete! 1. Which PPE is essential to protect the eyes from welding arc radiation?1. वेल्डिंग आर्क विकिरण से आँखों की रक्षा के लिए कौन सा पीपीई आवश्यक है? a) Safety glasses / सुरक्षा चश्मा b) Welding helmet with a proper shade lens / उचित शेड लेंस वाला वेल्डिंग हेलमेट c) Hand gloves / हाथ के दस्ताने d) Leather apron / चमड़े का एप्रन 2. The tool used to remove slag from a weld is a:2. वेल्ड से स्लैग हटाने के लिए उपयोग किया जाने वाला उपकरण है: a) Wire brush / वायर ब्रश b) Chipping hammer / चिपिंग हैमर c) Grinder / ग्राइंडर d) Tongs / चिमटा 3. In arc welding, the electrode is held in a:3. आर्क वेल्डिंग में, इलेक्ट्रोड को किसमें पकड़ा जाता है: a) Vice / वाइस b) Tongs / चिमटा c) Electrode holder / इलेक्ट्रोड होल्डर d) Earth clamp / अर्थ क्लैंप 4. A butt joint is used to join two plates that are:4. एक बट जॉइंट का उपयोग दो प्लेटों को जोड़ने के लिए किया जाता है जो: a) Placed edge to edge in the same plane / एक ही तल में किनारे से किनारा मिलाकर रखी गई हैं b) Overlapping each other / एक दूसरे को ओवरलैप कर रही हैं c) At a right angle to each other / एक दूसरे से समकोण पर हैं d) At an angle to each other / एक दूसरे से एक कोण पर हैं 5. The main purpose of flux coating on an electrode is to:5. एक इलेक्ट्रोड पर फ्लक्स कोटिंग का मुख्य उद्देश्य है: a) Make the electrode look good / इलेक्ट्रोड को अच्छा दिखाना b) Increase the current / करंट बढ़ाना c) Protect the weld pool from atmospheric contamination / वेल्ड पूल को वायुमंडलीय संदूषण से बचाना d) Cool the weld / वेल्ड को ठंडा करना 6. A Class C fire involves:6. एक क्लास C की आग में शामिल हैं: a) Wood, paper, and cloth / लकड़ी, कागज और कपड़ा b) Flammable liquids / ज्वलनशील तरल पदार्थ c) Energized electrical equipment / सक्रिय विद्युत उपकरण d) Combustible metals / ज्वलनशील धातुएं 7. In gas welding, the flame produced by mixing oxygen and acetylene is a(n):7. गैस वेल्डिंग में, ऑक्सीजन और एसिटिलीन को मिलाकर उत्पन्न की गई ज्वाला एक है: a) Oxidizing flame / ऑक्सीडाइजिंग फ्लेम b) Carburizing flame / कार्बराइजिंग फ्लेम c) Neutral flame / न्यूट्रल फ्लेम d) All of the above (depending on the mixture) / उपरोक्त सभी (मिश्रण के आधार पर) 8. The tool used to hold hot metal pieces is a:8. गर्म धातु के टुकड़ों को पकड़ने के लिए उपयोग किया जाने वाला उपकरण है: a) Hammer / हथौड़ा b) Tongs / चिमटा c) File / फाइल d) Scriber / स्क्राइबर 9. A ‘lap joint’ is where two plates are:9. एक ‘लैप जॉइंट’ वह है जहाँ दो प्लेटें होती हैं: a) Placed edge to edge / किनारे से किनारा मिलाकर रखी गई b) Placed with one overlapping the other / एक दूसरे को ओवरलैप करते हुए रखी गई c) Placed at a right angle / एक समकोण पर रखी गई d) Placed in a ‘T’ shape / एक ‘T’ आकार में रखी गई 10. The first aid for a small burn is to:10. एक छोटे से जलने के लिए प्राथमिक उपचार है: a) Apply grease or oil / ग्रीस या तेल लगाना b) Cover it with a dirty cloth / इसे एक गंदे कपड़े से ढकना c) Hold the burn under cool, running water / जले हुए को ठंडे, बहते पानी के नीचे रखना d) Burst any blisters / किसी भी फफोले को फोड़ना 11. A ‘fillet weld’ is used for joining:11. एक ‘फिलेट वेल्ड’ का उपयोग जोड़ने के लिए किया जाता है: a) Two plates edge to edge / दो प्लेटें किनारे से किनारा मिलाकर b) Two plates that form a corner, tee, or lap joint / दो प्लेटें जो एक कोना, टी, या लैप जॉइंट बनाती हैं c) Round bars end to end / गोल छड़ें सिरे से सिरा मिलाकर d) Thin sheets only / केवल पतली चादरें 12. The oxygen cylinder in a gas welding set is painted:12. एक गैस वेल्डिंग सेट में ऑक्सीजन सिलेंडर को पेंट किया जाता है: a) Red / लाल b) Black / काला c) Maroon / मैरून d) Blue / नीला 13. What is the main purpose of an earth clamp in arc welding?13. आर्क वेल्डिंग में एक अर्थ क्लैंप का मुख्य उद्देश्य क्या है? a) To hold the electrode / इलेक्ट्रोड को पकड़ना b) To complete the electrical circuit / विद्युत सर्किट को पूरा करना c) To clean the weld / वेल्ड को साफ करना d) To adjust the current / करंट को समायोजित करना 14. A ‘V’ groove preparation is done for a:14. एक ‘V’ खांचे की तैयारी किसके लिए की जाती है: a) Lap joint / लैप जॉइंट b) Tee joint / टी जॉइंट c) Butt joint / बट जॉइंट d) Corner joint / कॉर्नर जॉइंट 15. What is the most important safety rule in a welding shop?15. एक वेल्डिंग शॉप में सबसे महत्वपूर्ण सुरक्षा नियम क्या है? a) Wear appropriate PPE and ensure good ventilation / उपयुक्त पीपीई पहनना और अच्छा वेंटिलेशन सुनिश्चित करना b) Weld as quickly as possible / जितनी जल्दी हो सके वेल्ड करना c) Use the highest current setting / उच्चतम करंट सेटिंग का उपयोग करना d) Work near flammable materials / ज्वलनशील पदार्थों के पास काम करना 16. The process of joining two pieces of metal by heating them and using a filler metal with a lower melting point is:16. धातु के दो टुकड़ों को गर्म करके और कम गलनांक वाली एक भराव धातु का उपयोग करके जोड़ने की प्रक्रिया है: a) Welding / वेल्डिंग b) Brazing or Soldering / ब्रेज़िंग या सोल्डरिंग c) Forging / फोर्जिंग d) Riveting / रिवेटिंग 17. A ‘Tee Joint’ is formed when two plates are joined at:17. एक ‘टी जॉइंट’ तब बनता है जब दो प्लेटों को जोड़ा जाता है: a) 180 degrees / 180 डिग्री पर b) 90 degrees to each other in a ‘T’ shape / एक ‘T’ आकार में एक दूसरे से 90 डिग्री पर c) In the same plane / एक ही तल में d) Overlapping each other / एक दूसरे को ओवरलैप करते हुए 18. The tool used for making straight line marks on metal is a:18. धातु पर सीधी रेखा के निशान बनाने के लिए उपयोग किया जाने वाला उपकरण है: a) Scriber and straight edge / स्क्राइबर और स्ट्रेट एज b) Center punch / सेंटर पंच c) Divider / डिवाइडर d) Hammer / हथौड़ा 19. A ‘carburizing flame’ has an excess of:19. एक ‘कार्बराइजिंग फ्लेम’ में अधिकता होती है: a) Oxygen / ऑक्सीजन की b) Acetylene / एसिटिलीन की c) Nitrogen / नाइट्रोजन की d) Argon / आर्गन की 20. Which of these is a temporary fastener?20. इनमें से कौन एक अस्थायी फास्टनर है? a) Rivet / रिवेट b) Weld / वेल्ड c) Nut and Bolt / नट और बोल्ट d) Brazed joint / ब्रेज़्ड जोड़ 21. The most important quality of a good welder is:21. एक अच्छे वेल्डर का सबसे महत्वपूर्ण गुण है: a) Speed / गति b) Skill, a steady hand, and knowledge of safety / कौशल, एक स्थिर हाथ, और सुरक्षा का ज्ञान c) Strength / शक्ति d) Using the newest machine / नवीनतम मशीन का उपयोग करना 22. An ‘oxidizing flame’ has an excess of:22. एक ‘ऑक्सीडाइजिंग फ्लेम’ में अधिकता होती है: a) Oxygen / ऑक्सीजन की b) Acetylene / एसिटिलीन की c) Hydrogen / हाइड्रोजन की d) Nitrogen / नाइट्रोजन की 23. The tool used to clean a weld after chipping is a:23. चिपिंग के बाद एक वेल्ड को साफ करने के लिए उपयोग किया जाने वाला उपकरण है: a) Hammer / हथौड़ा b) File / फाइल c) Wire brush / वायर ब्रश d) Scraper / स्क्रैपर 24. What is the main safety risk from an electric arc?24. एक इलेक्ट्रिक आर्क से मुख्य सुरक्षा जोखिम क्या है? a) Loud noise / तेज शोर b) Intense ultraviolet (UV) radiation and sparks / तीव्र पराबैंगनी (UV) विकिरण और चिंगारी c) Bad smell / बुरी गंध d) Low temperature / कम तापमान 25. A fillet weld is roughly _______ in cross-section.25. एक फिलेट वेल्ड क्रॉस-सेक्शन में लगभग _______ होता है। a) Square / वर्गाकार b) Circular / वृत्ताकार c) Triangular / त्रिकोणीय d) Rectangular / आयताकार ← Previous Next → Finish Test / टेस्ट खत्म करें