ITI Surveyor 1st Year Mock Test – 2 July 17, 2025 ITI Surveyor 1st Year Mock Test – 2 | Instant Feedback ITI Surveyor 1st Year Mock Test – 2 आईटीआई सर्वेयर प्रथम वर्ष मॉक टेस्ट – 2 Time Left: 30:00 Test Complete! 1. If a surveyor’s chain is found to be too long, the measured distance will be:1. यदि एक सर्वेक्षक की चेन बहुत लंबी पाई जाती है, तो मापी गई दूरी होगी: a) More than the actual distance / वास्तविक दूरी से अधिक b) Less than the actual distance / वास्तविक दूरी से कम c) Equal to the actual distance / वास्तविक दूरी के बराबर d) Incorrect, but can be either more or less / गलत, लेकिन अधिक या कम हो सकती है 2. The Rise and Fall method of leveling provides a check on the calculation of:2. लेवलिंग की राइज़ एंड फॉल विधि किसकी गणना पर एक जांच प्रदान करती है: a) Backsights only / केवल बैकसाइट्स b) Foresights only / केवल फोरसाइट्स c) Intermediate sights and change points / इंटरमीडिएट साइट्स और चेंज पॉइंट्स d) The first reading only / केवल पहली रीडिंग 3. If the Fore Bearing (FB) of a line AB is 40°, its Back Bearing (BB) is:3. यदि एक रेखा AB का अग्र बियरिंग (FB) 40° है, तो इसका पश्च बियरिंग (BB) है: a) 40° b) 140° c) 220° d) 320° 4. The three-point problem is a method of:4. थ्री-पॉइंट प्रॉब्लम किसकी एक विधि है: a) Radiation / विकिरण b) Intersection / प्रतिच्छेदन c) Traversing / ट्रैवर्सिंग d) Resection / रिसेक्शन 5. An error that tends to accumulate and always occurs in the same direction is a:5. एक त्रुटि जो जमा होती जाती है और हमेशा एक ही दिशा में होती है, वह है: a) Compensating error / प्रतिकारी त्रुटि b) Cumulative error / संचयी त्रुटि c) Random error / यादृच्छिक त्रुटि d) Personal error / व्यक्तिगत त्रुटि 6. The correction for the curvature of the Earth in leveling is always:6. लेवलिंग में पृथ्वी की वक्रता के लिए सुधार हमेशा होता है: a) Additive / योगात्मक b) Subtractive / घटाव c) Zero / शून्य d) Sometimes additive, sometimes subtractive / कभी योगात्मक, कभी घटाव 7. A survey that starts and ends at the same point is called a:7. एक सर्वेक्षण जो एक ही बिंदु पर शुरू और समाप्त होता है, कहलाता है: a) Open traverse / खुला ट्रैवर्स b) Closed traverse / बंद ट्रैवर्स c) Link traverse / लिंक ट्रैवर्स d) Free traverse / फ्री ट्रैवर्स 8. A map scale of 1:1000 means that 1 cm on the map represents _______ on the ground.8. 1:1000 के नक्शे के पैमाने का मतलब है कि नक्शे पर 1 सेमी जमीन पर _______ का प्रतिनिधित्व करता है। a) 1 meter / 1 मीटर b) 10 meters / 10 मीटर c) 100 meters / 100 मीटर d) 1000 meters (1 km) / 1000 मीटर (1 किमी) 9. An obstacle that obstructs both chaining and ranging is a:9. एक बाधा जो चेनिंग और रेंजिंग दोनों में बाधा डालती है, वह है: a) Pond / तालाब b) River / नदी c) Building / इमारत d) Hill / पहाड़ी 10. A GTS Benchmark is a benchmark established by the:10. एक जीटीएस बेंचमार्क किसके द्वारा स्थापित एक बेंचमार्क है: a) Local municipality / स्थानीय नगर पालिका b) Survey of India department / भारतीय सर्वेक्षण विभाग c) Private survey company / निजी सर्वेक्षण कंपनी d) A local surveyor / एक स्थानीय सर्वेक्षक 11. A 20-meter metric chain consists of how many links?11. एक 20-मीटर मीट्रिक चेन में कितनी कड़ियाँ होती हैं? a) 50 links / 50 कड़ियाँ b) 100 links / 100 कड़ियाँ c) 150 links / 150 कड़ियाँ d) 200 links / 200 कड़ियाँ 12. The arithmetic check for the Rise and Fall method is:12. राइज़ एंड फॉल विधि के लिए अंकगणितीय जांच है: a) ΣB.S. + ΣF.S. = ΣRise + ΣFall b) ΣB.S. – ΣF.S. = Last R.L. – First R.L. = ΣRise – ΣFall c) ΣB.S. = ΣF.S. d) Last R.L. + First R.L. = ΣRise + ΣFall 13. The process of setting the plane table parallel to the position it occupied at previous stations is:13. प्लेन टेबल को उस स्थिति के समानांतर सेट करने की प्रक्रिया जो उसने पिछले स्टेशनों पर कब्जा कर रखी थी, है: a) Centering / सेंटरिंग b) Leveling / लेवलिंग c) Orientation / ओरिएंटेशन d) Sighting / साइटिंग 14. The difference between the Fore Bearing and Back Bearing of any line should be:14. किसी भी रेखा के अग्र बियरिंग और पश्च बियरिंग के बीच का अंतर होना चाहिए: a) 90° b) 180° c) 270° d) 360° 15. Which of the following is NOT an advantage of plane table surveying?15. निम्नलिखित में से कौन सा प्लेन टेबल सर्वेक्षण का लाभ नहीं है? a) The plot is drawn directly in the field / प्लॉट सीधे क्षेत्र में खींचा जाता है b) Omissions of measurements are unlikely / माप की चूक की संभावना नहीं है c) It is suitable for work in rainy or wet conditions / यह बरसात या गीली परिस्थितियों में काम के लिए उपयुक्त है d) Contours and irregular objects can be plotted accurately / कंटूर और अनियमित वस्तुओं को सटीक रूप से प्लॉट किया जा सकता है 16. Dimension lines in a drawing are typically drawn as:16. एक ड्राइंग में विमा रेखाएं आमतौर पर खींची जाती हैं: a) Thick continuous lines / मोटी सतत रेखाओं के रूप में b) Thin continuous lines / पतली सतत रेखाओं के रूप में c) Dashed lines / धराशायी रेखाओं के रूप में d) Chain lines / चेन रेखाओं के रूप में 17. A cross staff is an instrument used for:17. एक क्रॉस स्टाफ एक उपकरण है जिसका उपयोग किया जाता है: a) Measuring distances / दूरियों को मापने के लिए b) Setting out right angles (90°) / समकोण (90°) स्थापित करने के लिए c) Measuring bearings / बियरिंग मापने के लिए d) Determining levels / स्तरों का निर्धारण करने के लिए 18. The correction for refraction in leveling is always:18. लेवलिंग में अपवर्तन के लिए सुधार हमेशा होता है: a) Subtractive / घटाव b) Additive / योगात्मक c) Zero / शून्य d) Equal to the curvature correction / वक्रता सुधार के बराबर 19. A Surveyor’s compass is used to measure:19. एक सर्वेक्षक कम्पास का उपयोग मापने के लिए किया जाता है: a) Whole Circle Bearings (WCB) / पूर्ण वृत्त बियरिंग (WCB) b) Quadrantal Bearings (RB) / चतुर्भुज बियरिंग (RB) c) True Bearings / यथार्थ बियरिंग d) Horizontal distances / क्षैतिज दूरियाँ 20. What is the main purpose of a U-fork (or plumbing fork) in plane table surveying?20. प्लेन टेबल सर्वेक्षण में एक यू-फोर्क (या प्लंबिंग फोर्क) का मुख्य उद्देश्य क्या है? a) To level the table / टेबल को समतल करने के लिए b) To orient the table / टेबल को उन्मुख करने के लिए c) To center the table over the ground station / टेबल को ग्राउंड स्टेशन के ऊपर केंद्रित करने के लिए d) To hold the drawing sheet / ड्राइंग शीट को पकड़ने के लिए 21. Simpson’s rule for area calculation is generally more accurate than the:21. क्षेत्रफल की गणना के लिए सिम्पसन का नियम आम तौर पर किससे अधिक सटीक है: a) Trapezoidal rule / ट्रेपेज़ॉइडल नियम b) Mid-ordinate rule / मिड-ऑर्डिनेट नियम c) Average ordinate rule / एवरेज-ऑर्डिनेट नियम d) It is the least accurate method / यह सबसे कम सटीक विधि है 22. An offset rod is primarily used to measure:22. एक ऑफसेट रॉड का उपयोग मुख्य रूप से मापने के लिए किया जाता है: a) Long distances / लंबी दूरियाँ b) Vertical angles / ऊर्ध्वाधर कोण c) Short offsets from the chain line / चेन लाइन से छोटे ऑफसेट d) Bearings / बियरिंग 23. In the quadrantal bearing system, bearings are measured from:23. चतुर्भुज बियरिंग प्रणाली में, बियरिंग को मापा जाता है: a) North only, clockwise / केवल उत्तर से, दक्षिणावर्त b) South only, clockwise / केवल दक्षिण से, दक्षिणावर्त c) Either North or South, towards East or West / या तो उत्तर या दक्षिण से, पूर्व या पश्चिम की ओर d) East only, counter-clockwise / केवल पूर्व से, वामावर्त 24. What does R.F. stand for in the context of map scales?24. नक्शे के पैमानों के संदर्भ में R.F. का क्या अर्थ है? a) Ranging Factor / रेंजिंग फैक्टर b) Representative Fraction / रिप्रेजेंटेटिव फ्रैक्शन c) Reduced Fraction / रेड्यूस्ड फ्रैक्शन d) Reference Factor / रेफरेंस फैक्टर 25. A temporary benchmark is:25. एक अस्थायी बेंचमार्क है: a) Established by the Survey of India / भारतीय सर्वेक्षण द्वारा स्थापित b) A point of known elevation that is highly permanent / ज्ञात ऊंचाई का एक बिंदु जो अत्यधिक स्थायी है c) Established at the end of a day’s work to be used the next day / दिन के काम के अंत में स्थापित किया जाता है ताकि अगले दिन उपयोग किया जा सके d) The highest point in the survey area / सर्वेक्षण क्षेत्र में उच्चतम बिंदु ← Previous Next → Finish Test / टेस्ट खत्म करें