ITI MRAC 2nd Year Mock Test – 5 July 16, 2025 ITI MRAC 2nd Year Mock Test – 5 | Instant Feedback ITI MRAC 2nd Year Mock Test – 5 आईटीआई एमआरएसी द्वितीय वर्ष मॉक टेस्ट – 5 Time Left: 30:00 Test Complete! 1. The final step in commissioning a new HVAC installation is typically:1. एक नए एचवीएसी इंस्टॉलेशन को चालू करने का अंतिम चरण आमतौर पर होता है: a) Charging the system with refrigerant / सिस्टम को रेफ्रिजरेंट से चार्ज करना b) Painting the outdoor unit / आउटडोर यूनिट को पेंट करना c) Handing over documents and providing training to the operator / दस्तावेज़ सौंपना और ऑपरेटर को प्रशिक्षण प्रदान करना d) Washing the entire system / पूरे सिस्टम को धोना 2. If a compressor is running but pressures on the high and low side are nearly equal, the most likely fault is:2. यदि एक कंप्रेसर चल रहा है लेकिन उच्च और निम्न साइड पर दाब लगभग बराबर है, तो सबसे संभावित दोष है: a) Refrigerant overcharge / रेफ्रिजरेंट ओवरचार्ज b) An internal compressor fault (e.g., broken valves) / एक आंतरिक कंप्रेसर दोष (जैसे, टूटे हुए वाल्व) c) A blocked condenser coil / एक अवरुद्ध कंडेनसर कॉइल d) Low ambient temperature / निम्न परिवेश का तापमान 3. On a psychrometric chart, lines of constant enthalpy are also lines of constant:3. एक साइकोमेट्रिक चार्ट पर, स्थिर एन्थैल्पी की रेखाएं किसकी स्थिर रेखाएं भी होती हैं: a) Dry-bulb temperature / ड्राई-बल्ब तापमान b) Relative humidity / सापेक्ष आर्द्रता c) Wet-bulb temperature / वेट-बल्ब तापमान d) Specific volume / विशिष्ट आयतन 4. “Static regain” in duct design refers to the:4. डक्ट डिजाइन में “स्टैटिक रिगेन” का अर्थ है: a) Loss of static pressure due to friction / घर्षण के कारण स्थैतिक दाब का नुकसान b) Increase in static pressure when air velocity decreases / हवा का वेग कम होने पर स्थैतिक दाब में वृद्धि c) Total pressure in the duct / डक्ट में कुल दाब d) The noise made by the ductwork / डक्टवर्क द्वारा किया गया शोर 5. What is the main difference between EER and SEER energy efficiency ratings?5. EER और SEER ऊर्जा दक्षता रेटिंग के बीच मुख्य अंतर क्या है? a) EER is for heating, SEER is for cooling / EER हीटिंग के लिए है, SEER कूलिंग के लिए है b) SEER is an average efficiency over a cooling season, while EER is at a single test condition / SEER एक कूलिंग सीजन में औसत दक्षता है, जबकि EER एक एकल परीक्षण स्थिति पर है c) EER is used for US models, SEER is for European models / EER का उपयोग अमेरिकी मॉडल के लिए किया जाता है, SEER का उपयोग यूरोपीय मॉडल के लिए किया जाता है d) There is no difference / कोई अंतर नहीं है 6. In an ice plant, an agitator is used in the brine tank to:6. एक बर्फ के कारखाने में, ब्राइन टैंक में एक एजिटेटर का उपयोग किया जाता है: a) Mix the salt with the water / नमक को पानी के साथ मिलाने के लिए b) Circulate the brine for uniform temperature and faster freezing / समान तापमान और तेजी से जमने के लिए ब्राइन को प्रसारित करने के लिए c) Keep the brine from freezing / ब्राइन को जमने से बचाने के लिए d) Remove the ice cans / बर्फ के डिब्बे हटाने के लिए 7. A car’s AC blower motor resistor is used to:7. एक कार के एसी ब्लोअर मोटर रेसिस्टर का उपयोग किया जाता है: a) Start the blower motor / ब्लोअर मोटर शुरू करने के लिए b) Protect the motor from overheating / मोटर को ज़्यादा गरम होने से बचाने के लिए c) Control the different fan speeds / विभिन्न पंखे की गति को नियंत्रित करने के लिए d) Change the direction of airflow / वायु प्रवाह की दिशा बदलने के लिए 8. Before opening a chiller system for major service, what is the most critical first step?8. बड़ी सर्विस के लिए चिलर सिस्टम खोलने से पहले, सबसे महत्वपूर्ण पहला कदम क्या है? a) Switch off the main power / मुख्य बिजली बंद करना b) Safely recover all refrigerant from the system / सिस्टम से सभी रेफ्रिजरेंट को सुरक्षित रूप से रिकवर करना c) Drain the water from the system / सिस्टम से पानी निकालना d) Clean the outside of the chiller / चिलर के बाहर की सफाई करना 9. BACnet is a:9. BACnet एक है: a) Type of refrigerant / रेफ्रिजरेंट का एक प्रकार b) Brand of air conditioner / एयर कंडीशनर का एक ब्रांड c) Communication protocol for building automation and control / बिल्डिंग ऑटोमेशन और नियंत्रण के लिए एक संचार प्रोटोकॉल d) Type of compressor oil / कंप्रेसर तेल का एक प्रकार 10. The process of replacing an old refrigerant (e.g., R-22) with a new one (e.g., R-407C) in a system is called:10. एक सिस्टम में एक पुराने रेफ्रिजरेंट (जैसे, R-22) को एक नए (जैसे, R-407C) से बदलने की प्रक्रिया कहलाती है: a) Reclaiming / रिक्लेमिंग b) Retrofitting / रेट्रोफिटिंग c) Recycling / रीसाइक्लिंग d) Recovery / रिकवरी 11. A megohmmeter (Megger) test is performed on a compressor motor to check the:11. एक कंप्रेसर मोटर पर एक मेगोहमीटर (मेगर) परीक्षण यह जांचने के लिए किया जाता है: a) Running current / रनिंग करंट b) Starting torque / स्टार्टिंग टॉर्क c) Integrity of the winding insulation / वाइंडिंग इंसुलेशन की अखंडता d) Speed of the motor / मोटर की गति 12. Evacuating a system to a deep vacuum (e.g., 500 microns) is critical because it:12. एक सिस्टम को गहरे वैक्यूम (जैसे, 500 माइक्रोन) तक खाली करना महत्वपूर्ण है क्योंकि यह: a) Cleans the oil / तेल को साफ करता है b) Lowers the boiling point of water, ensuring all moisture is removed / पानी का क्वथनांक कम करता है, यह सुनिश्चित करता है कि सारी नमी हटा दी गई है c) Tests the pressure switches / प्रेशर स्विच का परीक्षण करता है d) Cools the system down before charging / चार्ज करने से पहले सिस्टम को ठंडा करता है 13. In duct design, turning vanes are installed inside square elbows to:13. डक्ट डिजाइन में, चौकोर कोहनी के अंदर टर्निंग वेन्स स्थापित किए जाते हैं: a) Increase the air speed / हवा की गति बढ़ाने के लिए b) Filter the air / हवा को फ़िल्टर करने के लिए c) Reduce turbulence and pressure loss / अशांति और दाब की हानि को कम करने के लिए d) Make the duct stronger / डक्ट को मजबूत बनाने के लिए 14. Which of these is a positive displacement compressor?14. इनमें से कौन सा एक पॉजिटिव डिस्प्लेसमेंट कंप्रेसर है? a) Centrifugal compressor / सेंट्रीफ्यूगल कंप्रेसर b) Axial compressor / एक्सियल कंप्रेसर c) Scroll compressor / स्क्रॉल कंप्रेसर d) Ejector / इजेक्टर 15. A high temperature refrigeration application is:15. एक उच्च तापमान प्रशीतन अनुप्रयोग है: a) A deep freezer (-20°C) / एक डीप फ्रीजर (-20°C) b) An ice plant (-10°C) / एक बर्फ का कारखाना (-10°C) c) Air conditioning (~7°C evaporator) / एयर कंडीशनिंग (~7°C इवैपोरेटर) d) A blast freezer (-40°C) / एक ब्लास्ट फ्रीजर (-40°C) 16. The Coefficient of Performance (COP) of a refrigeration system is the ratio of:16. एक प्रशीतन प्रणाली का प्रदर्शन गुणांक (COP) किसका अनुपात है: a) Heat rejected to work input / अस्वीकृत ऊष्मा का कार्य इनपुट से b) Refrigerating effect (cooling) to work input / प्रशीतन प्रभाव (कूलिंग) का कार्य इनपुट से c) Work input to heat rejected / कार्य इनपुट का अस्वीकृत ऊष्मा से d) Work input to refrigerating effect / कार्य इनपुट का प्रशीतन प्रभाव से 17. A warm liquid line and a hot suction line at the compressor could indicate:17. कंप्रेसर पर एक गर्म लिक्विड लाइन और एक गर्म सक्शन लाइन यह संकेत दे सकती है: a) A severe refrigerant shortage / एक गंभीर रेफ्रिजरेंट की कमी b) A refrigerant overcharge / एक रेफ्रिजरेंट ओवरचार्ज c) Normal operation / सामान्य संचालन d) A stuck-open expansion valve / एक खुला अटका हुआ विस्तार वाल्व 18. The main purpose of a filter-drier is to remove:18. एक फिल्टर-ड्रायर का मुख्य उद्देश्य हटाना है: a) Heat and noise / गर्मी और शोर b) Oil from the refrigerant / रेफ्रिजरेंट से तेल c) Moisture and solid contaminants / नमी और ठोस संदूषक d) Air from the system / सिस्टम से हवा 19. A “DX” or Direct Expansion system means:19. एक “DX” या डायरेक्ट एक्सपेंशन सिस्टम का मतलब है: a) The evaporator is located directly in the air stream to be cooled / इवैपोरेटर सीधे ठंडी की जाने वाली वायु धारा में स्थित है b) The system uses water to cool the air / सिस्टम हवा को ठंडा करने के लिए पानी का उपयोग करता है c) The compressor is located inside the room / कंप्रेसर कमरे के अंदर स्थित है d) The expansion valve is electronically controlled / विस्तार वाल्व इलेक्ट्रॉनिक रूप से नियंत्रित होता है 20. Which component protects a motor from sustained small overcurrents?20. कौन सा घटक एक मोटर को निरंतर छोटे ओवरकरंट से बचाता है? a) A fuse / एक फ्यूज b) An overload protector / एक ओवरलोड प्रोटेक्टर c) A start capacitor / एक स्टार्ट कैपेसिटर d) The ground wire / ग्राउंड वायर 21. When pressure testing a system with nitrogen, the test pressure should not exceed:21. नाइट्रोजन के साथ एक सिस्टम का दाब परीक्षण करते समय, परीक्षण दाब इससे अधिक नहीं होना चाहिए: a) The pressure of the nitrogen cylinder / नाइट्रोजन सिलेंडर का दाब b) The system’s low-side test pressure rating / सिस्टम की लो-साइड टेस्ट प्रेशर रेटिंग c) 100 psi / 100 psi d) The setting of the high-pressure switch / हाई-प्रेशर स्विच की सेटिंग 22. The primary function of the condenser in a car AC is to:22. एक कार एसी में कंडेनसर का प्राथमिक कार्य है: a) Absorb heat from the cabin / केबिन से गर्मी को अवशोषित करना b) Reject heat from the refrigerant to the outside air / रेफ्रिजरेंट से गर्मी को बाहरी हवा में बाहर निकालना c) Filter the refrigerant / रेफ्रिजरेंट को फ़िल्टर करना d) Store liquid refrigerant / तरल रेफ्रिजरेंट का भंडारण करना 23. The “bypass factor” of a cooling coil indicates:23. एक कूलिंग कॉइल का “बाईपास फैक्टर” इंगित करता है: a) How efficient the coil is / कॉइल कितनी कुशल है b) The fraction of air that passes through the coil without being cooled / हवा का वह अंश जो ठंडा हुए बिना कॉइल से गुजरता है c) The pressure drop across the coil / कॉइल के पार दाब में गिरावट d) The amount of refrigerant bypassing the coil / कॉइल को बाईपास करने वाले रेफ्रिजरेंट की मात्रा 24. The final action after completing any refrigeration service should be:24. किसी भी प्रशीतन सेवा को पूरा करने के बाद अंतिम कार्रवाई होनी चाहिए: a) To wash the unit / यूनिट को धोना b) To paint the pipes / पाइप को पेंट करना c) A thorough leak check / एक संपूर्ण रिसाव जांच d) To overcharge the system slightly / सिस्टम को थोड़ा ओवरचार्ज करना 25. A reversing valve is the key component that allows a system to function as a:25. एक रिवर्सिंग वाल्व एक प्रमुख घटक है जो एक प्रणाली को इस रूप में कार्य करने की अनुमति देता है: a) Chiller / चिलर b) Heat pump / हीट पंप c) Dehumidifier / डीह्यूमिडिफायर d) Freezer / फ्रीजर ← Previous Next → Finish Test / टेस्ट खत्म करें