ITI MRAC 1st Year Mock Test – 3 July 15, 2025 ITI MRAC 1st Year Mock Test – 3 | Instant Feedback ITI MRAC 1st Year Mock Test – 3 आईटीआई एमआरएसी प्रथम वर्ष मॉक टेस्ट – 3 Time Left: 30:00 Test Complete! 1. Which class of fire extinguisher is used for electrical fires?1. बिजली से लगी आग के लिए किस श्रेणी के अग्निशामक का उपयोग किया जाता है? a) Class A b) Class B c) Class C d) Class D 2. A flaring tool is used to:2. फ्लेयरिंग टूल का उपयोग किया जाता है: a) Create a flared connection on copper tubing / तांबे की ट्यूबिंग पर फ्लेयर्ड कनेक्शन बनाने के लिए b) Cut copper tubing / तांबे की ट्यूबिंग काटने के लिए c) Bend copper tubing / तांबे की ट्यूबिंग मोड़ने के लिए d) Clean copper tubing / तांबे की ट्यूबिंग साफ करने के लिए 3. Ohm’s law states that:3. ओम का नियम बताता है कि: a) P = V × I b) V = I × R c) V = I / R d) R = V / P 4. In which component of the refrigeration cycle does the refrigerant absorb heat?4. प्रशीतन चक्र के किस घटक में रेफ्रिजरेंट ऊष्मा को अवशोषित करता है? a) Compressor / कंप्रेसर b) Condenser / कंडेनसर c) Expansion Valve / विस्तार वाल्व d) Evaporator / इवैपोरेटर 5. Which tool is specifically designed for bending soft copper tubing?5. नरम तांबे की ट्यूबिंग को मोड़ने के लिए विशेष रूप से कौन सा उपकरण डिज़ाइन किया गया है? a) Pliers / प्लायर्स b) Pipe wrench / पाइप रिंच c) Tube bender / ट्यूब बेंडर d) Hacksaw / हैकसॉ 6. The unit of electrical power is:6. विद्युत शक्ति की इकाई है: a) Volt / वोल्ट b) Ampere / एम्पीयर c) Ohm / ओम d) Watt / वाट 7. Which of the following is an HFC refrigerant?7. निम्नलिखित में से कौन सा एक HFC रेफ्रिजरेंट है? a) R-12 b) R-22 c) R-134a d) R-11 8. Which device protects a motor from overheating due to excessive current?8. कौन सा उपकरण मोटर को अत्यधिक करंट के कारण गर्म होने से बचाता है? a) Fuse / फ्यूज b) Capacitor / कैपेसिटर c) Overload protector / ओवरलोड प्रोटेक्टर d) Thermostat / थर्मोस्टेट 9. The process of expanding the end of one tube to fit another tube of the same diameter is called:9. एक ट्यूब के सिरे को उसी व्यास की दूसरी ट्यूब में फिट करने के लिए फैलाने की प्रक्रिया को कहा जाता है: a) Flaring / फ्लेयरिंग b) Brazing / ब्रेज़िंग c) Swaging / स्वेजिंग d) Pinching / पिंचिंग 10. Heat can travel through a vacuum by which method?10. ऊष्मा निर्वात में किस विधि से यात्रा कर सकती है? a) Conduction / चालन b) Convection / संवहन c) Radiation / विकिरण d) It cannot travel in a vacuum / यह निर्वात में यात्रा नहीं कर सकती 11. What is the state of the refrigerant when it enters the compressor?11. कंप्रेसर में प्रवेश करते समय रेफ्रिजरेंट की अवस्था क्या होती है? a) High-pressure liquid / उच्च दाब तरल b) Low-pressure liquid / निम्न दाब तरल c) High-pressure vapor / उच्च दाब वाष्प d) Low-pressure vapor / निम्न दाब वाष्प 12. Which instrument is used to measure the diameter of a wire with high precision?12. उच्च परिशुद्धता के साथ तार का व्यास मापने के लिए किस उपकरण का उपयोग किया जाता है? a) Steel Rule / स्टील रूल b) Micrometer / माइक्रोमीटर c) Try Square / ट्राई स्क्वायर d) Divider / डिवाइडर 13. The main environmental concern with CFC refrigerants like R-12 is:13. R-12 जैसे CFC रेफ्रिजरेंट के साथ मुख्य पर्यावरणीय चिंता है: a) Global Warming / ग्लोबल वार्मिंग b) Ozone Layer Depletion / ओजोन परत का क्षरण c) Acid Rain / अम्लीय वर्षा d) Flammability / ज्वलनशीलता 14. To measure current, an ammeter must be connected in:14. करंट मापने के लिए, एक एमीटर को जोड़ा जाना चाहिए: a) Series with the circuit / सर्किट के साथ श्रृंखला में b) Parallel with the circuit / सर्किट के समानांतर c) Either series or parallel / या तो श्रृंखला या समानांतर d) Across the power source only / केवल शक्ति स्रोत के पार 15. What process occurs in the condenser?15. कंडेनसर में कौन सी प्रक्रिया होती है? a) High-pressure vapor turns into low-pressure vapor / उच्च दाब वाष्प निम्न दाब वाष्प में बदल जाती है b) Low-pressure liquid turns into low-pressure vapor / निम्न दाब तरल निम्न दाब वाष्प में बदल जाता है c) High-pressure vapor turns into high-pressure liquid / उच्च दाब वाष्प उच्च दाब तरल में बदल जाती है d) Low-pressure vapor turns into high-pressure vapor / निम्न दाब वाष्प उच्च दाब वाष्प में बदल जाती है 16. The process of softening a metal by heating it and then allowing it to cool slowly is called:16. किसी धातु को गर्म करके और फिर उसे धीरे-धीरे ठंडा होने देकर नरम करने की प्रक्रिया कहलाती है: a) Hardening / हार्डनिंग b) Tempering / टेम्परिंग c) Annealing / एनीलिंग d) Quenching / क्वेंचिंग 17. A manifold gauge set is used primarily to measure:17. मैनिफोल्ड गेज सेट का उपयोग मुख्य रूप से मापने के लिए किया जाता है: a) Temperature / तापमान b) Pressure / दाब c) Humidity / आर्द्रता d) Voltage / वोल्टेज 18. What is specific heat?18. विशिष्ट ऊष्मा क्या है? a) The total heat in a substance / किसी पदार्थ में कुल ऊष्मा b) Heat required to change phase / अवस्था बदलने के लिए आवश्यक ऊष्मा c) Heat required to raise the temperature of 1kg of a substance by 1°C / 1 किलो पदार्थ का तापमान 1°C बढ़ाने के लिए आवश्यक ऊष्मा d) The temperature of a substance / किसी पदार्थ का तापमान 19. A capillary tube in a small refrigeration system functions as a(n):19. एक छोटे प्रशीतन प्रणाली में एक केशिका ट्यूब (कैपिलरी ट्यूब) किस रूप में कार्य करती है? a) Compressor / कंप्रेसर b) Condenser / कंडेनसर c) Filter-Drier / फिल्टर-ड्रायर d) Expansion device / विस्तार उपकरण 20. What is the standard color code for a nitrogen cylinder used in HVAC/R?20. HVAC/R में उपयोग होने वाले नाइट्रोजन सिलेंडर के लिए मानक रंग कोड क्या है? a) Black / काला b) Blue / नीला c) Green / हरा d) Yellow / पीला 21. What is the primary function of a relay in an electrical circuit?21. एक विद्युत परिपथ में रिले का प्राथमिक कार्य क्या है? a) To store electrical charge / विद्युत आवेश का भंडारण करना b) To resist the flow of current / धारा के प्रवाह का विरोध करना c) To use a small current to switch a larger current / एक बड़े करंट को स्विच करने के लिए एक छोटे करंट का उपयोग करना d) To increase the voltage / वोल्टेज बढ़ाना 22. The point angle of a center punch is typically:22. एक सेंटर पंच का बिंदु कोण आम तौर पर होता है: a) 30° b) 60° c) 90° d) 120° 23. “Subcooling” in a refrigeration system refers to cooling the refrigerant:23. एक प्रशीतन प्रणाली में “सबकूलिंग” का अर्थ रेफ्रिजरेंट को ठंडा करना है: a) In its vapor state / इसकी वाष्प अवस्था में b) Below its saturation temperature while it is a liquid / इसके संतृप्ति तापमान से नीचे जब यह एक तरल है c) Exactly to its freezing point / ठीक इसके हिमांक तक d) Above its saturation temperature while it is a vapor / इसके संतृप्ति तापमान से ऊपर जब यह एक वाष्प है 24. Which type of pliers is best for gripping small components in tight spaces?24. तंग जगहों में छोटे घटकों को पकड़ने के लिए किस प्रकार के प्लायर्स सबसे अच्छे होते हैं? a) Slip-joint pliers / स्लिप-जॉइंट प्लायर्स b) Lineman’s pliers / लाइनमैन प्लायर्स c) Needle-nose pliers / नीडल-नोज प्लायर्स d) Groove-joint pliers / ग्रूव-जॉइंट प्लायर्स 25. Why is it essential to evacuate a refrigeration system before charging with refrigerant?25. रेफ्रिजरेंट से चार्ज करने से पहले एक प्रशीतन प्रणाली को इवैक्यूएट (खाली) करना क्यों आवश्यक है? a) To cool down the system / सिस्टम को ठंडा करने के लिए b) To remove air and moisture / हवा और नमी को हटाने के लिए c) To check for leaks / लीक की जांच करने के लिए d) To increase the pressure inside / अंदर का दाब बढ़ाने के लिए ← Previous Next → Finish Test / टेस्ट खत्म करें