ITI Engineering Drawing 2nd Year Mock Test – 4 July 18, 2025 ITI Engineering Drawing 2nd Year Mock Test – 4 | Instant Feedback ITI Engineering Drawing 2nd Year Mock Test – 4 आईटीआई इंजीनियरिंग ड्राइंग द्वितीय वर्ष मॉक टेस्ट – 4 Time Left: 30:00 Test Complete! 1. What is the main purpose of a fixture in manufacturing?1. विनिर्माण में एक फिक्स्चर का मुख्य उद्देश्य क्या है? a) To guide the cutting tool / कटिंग टूल का मार्गदर्शन करना b) To hold and locate the workpiece during an operation / एक ऑपरेशन के दौरान वर्कपीस को पकड़ना और पता लगाना c) To measure the workpiece / वर्कपीस को मापना d) To cool the workpiece / वर्कपीस को ठंडा करना 2. The radial distance from the pitch circle to the top of the gear tooth is:2. पिच सर्कल से गियर के दांत के शीर्ष तक की रेडियल दूरी है: a) Dedendum / डिडेंडम b) Addendum / एडेंडम c) Circular pitch / सर्कुलर पिच d) Clearance / क्लीयरेंस 3. A “transition fit” is one where the tolerance zones of the hole and shaft:3. एक “ट्रांजिशन फिट” वह है जिसमें छेद और शाफ्ट के टॉलरेंस जोन: a) Always result in a clearance / हमेशा एक क्लीयरेंस में परिणामित होते हैं b) Always result in an interference / हमेशा एक इंटरफेरेंस में परिणामित होते हैं c) Overlap / ओवरलैप करते हैं d) Have no relation / कोई संबंध नहीं रखते हैं 4. The CAD command to create a beveled edge between two lines is:4. दो रेखाओं के बीच एक बेवेल्ड किनारा बनाने के लिए CAD कमांड है: a) FILLET / फिलेट b) TRIM / ट्रिम c) CHAMFER / चैम्फर d) OFFSET / ऑफसेट 5. In a welding symbol, a circle around the junction of the arrow and reference line indicates:5. एक वेल्डिंग प्रतीक में, एरो और संदर्भ रेखा के जंक्शन के चारों ओर एक वृत्त इंगित करता है: a) Weld to be done on site / वेल्ड को साइट पर किया जाना है b) Weld all around / चारों ओर वेल्ड करना है c) A circular weld / एक वृत्ताकार वेल्ड d) A spot weld / एक स्पॉट वेल्ड 6. The heat treatment process of heating steel and then cooling it slowly in a furnace is:6. स्टील को गर्म करने और फिर उसे भट्ठी में धीरे-धीरे ठंडा करने की ऊष्मा उपचार प्रक्रिया है: a) Hardening / हार्डनिंग b) Tempering / टेम्परिंग c) Annealing / एनीलिंग d) Normalizing / नॉर्मलाइजिंग 7. The 3-2-1 principle of location is used to restrict a workpiece’s:7. लोकेशन के 3-2-1 सिद्धांत का उपयोग एक वर्कपीस को प्रतिबंधित करने के लिए किया जाता है: a) Size / आकार b) Weight / वजन c) Degrees of freedom / स्वतंत्रता की डिग्री d) Material / सामग्री 8. The gear train used for large speed reduction between non-intersecting, perpendicular shafts is:8. गैर-प्रतिच्छेदी, लंबवत शाफ्टों के बीच बड़ी गति में कमी के लिए उपयोग किया जाने वाला गियर ट्रेन है: a) Spur gears / स्पर गियर b) Bevel gears / बेवल गियर c) Worm and worm wheel / वर्म और वर्म व्हील d) Helical gears / हेलिकल गियर 9. The ‘NO GO’ end of a plug gauge checks the:9. एक प्लग गेज का ‘NO GO’ सिरा जांचता है: a) Lower limit of the hole size / छेद के आकार की निचली सीमा b) Upper limit of the hole size / छेद के आकार की ऊपरी सीमा c) Roundness of the hole / छेद की गोलाई d) Depth of the hole / छेद की गहराई 10. The main purpose of a fixture is to:10. एक फिक्स्चर का मुख्य उद्देश्य है: a) Guide the cutting tool / कटिंग टूल का मार्गदर्शन करना b) Hold and locate the workpiece during machining / मशीनिंग के दौरान वर्कपीस को पकड़ना और पता लगाना c) Hold the cutting tool / कटिंग टूल को पकड़ना d) Both hold and guide the tool / टूल को पकड़ना और मार्गदर्शन करना दोनों 11. A ‘transition fit’ may result in:11. एक ‘ट्रांजिशन फिट’ का परिणाम हो सकता है: a) Always clearance / हमेशा क्लीयरेंस b) Always interference / हमेशा इंटरफेरेंस c) Either clearance or interference / या तो क्लीयरेंस या इंटरफेरेंस d) A very tight fit / एक बहुत टाइट फिट 12. Which of these is a non-ferrous metal?12. इनमें से कौन एक अलौह धातु है? a) Mild Steel / माइल्ड स्टील b) Cast Iron / कच्चा लोहा c) Zinc / जस्ता d) High Carbon Steel / उच्च कार्बन स्टील 13. The drawing that contains a parts list or BOM is an:13. वह ड्राइंग जिसमें एक पार्ट्स सूची या BOM होता है, वह है: a) Assembly drawing / असेंबली ड्राइंग b) Detail drawing / डिटेल ड्राइंग c) Part drawing / पार्ट ड्राइंग d) Schematic drawing / योजनाबद्ध ड्राइंग 14. What is the main purpose of a jig bush?14. एक जिग बुश का मुख्य उद्देश्य क्या है? a) To locate the workpiece / वर्कपीस का पता लगाना b) To provide a hardened, accurate guide for a drill / एक ड्रिल के लिए एक कठोर, सटीक गाइड प्रदान करना c) To clamp the workpiece / वर्कपीस को क्लैंप करना d) To hold the jig itself / जिग को ही पकड़ना 15. The ‘module’ of a gear is the ratio of:15. एक गियर का ‘मॉड्यूल’ किसका अनुपात है: a) Pitch circle diameter to the number of teeth / पिच सर्कल व्यास का दांतों की संख्या से b) Number of teeth to the pitch circle diameter / दांतों की संख्या का पिच सर्कल व्यास से c) Addendum to dedendum / एडेंडम का डिडेंडम से d) Face width to the number of teeth / फेस की चौड़ाई का दांतों की संख्या से 16. The CAD command to create a block of objects for repeated use is:16. बार-बार उपयोग के लिए वस्तुओं का एक ब्लॉक बनाने के लिए CAD कमांड है: a) GROUP / ग्रुप b) BLOCK / ब्लॉक c) ARRAY / ऐरे d) POLYLINE / पॉलीलाइन 17. In the ‘shaft basis’ system, the basic size is the:17. ‘शाफ्ट बेसिस’ प्रणाली में, मूल आकार है: a) Maximum size of the shaft / शाफ्ट का अधिकतम आकार b) Minimum size of the shaft / शाफ्ट का न्यूनतम आकार c) Maximum size of the hole / छेद का अधिकतम आकार d) Minimum size of the hole / छेद का न्यूनतम आकार 18. Case hardening is a process to harden the:18. केस हार्डनिंग किसको कठोर करने की एक प्रक्रिया है: a) Core of the material / सामग्री के कोर को b) Surface of the material / सामग्री की सतह को c) Entire material throughout / पूरी सामग्री को d) Welded joints only / केवल वेल्डेड जोड़ों को 19. The number written to the right of a weld symbol often indicates:19. एक वेल्ड प्रतीक के दाईं ओर लिखी गई संख्या अक्सर इंगित करती है: a) The size of the weld / वेल्ड का आकार b) The length of the weld / वेल्ड की लंबाई c) The welding process / वेल्डिंग प्रक्रिया d) The number of welds / वेल्ड की संख्या 20. Which of the following is a key component of a pipe vice?20. निम्नलिखित में से कौन एक पाइप वाइस का एक प्रमुख घटक है? a) A flat jaw / एक सपाट जबड़ा b) A V-shaped jaw / एक V-आकार का जबड़ा c) A sliding jaw only / केवल एक स्लाइडिंग जबड़ा d) A handle / एक हैंडल 21. What is the primary safety measure before starting work on a machine?21. एक मशीन पर काम शुरू करने से पहले प्राथमिक सुरक्षा उपाय क्या है? a) Ensure it is clean / सुनिश्चित करें कि यह साफ है b) Check that all safety guards are in place and working / जांचें कि सभी सुरक्षा गार्ड अपनी जगह पर हैं और काम कर रहे हैं c) Wear loose clothing / ढीले कपड़े पहनें d) Have a cup of tea / एक कप चाय पिएं 22. The gears used to connect parallel shafts are typically:22. समानांतर शाफ्टों को जोड़ने के लिए उपयोग किए जाने वाले गियर आमतौर पर होते हैं: a) Bevel gears / बेवल गियर b) Worm gears / वर्म गियर c) Spur or Helical gears / स्पर या हेलिकल गियर d) Rack and pinion / रैक और पिनियन 23. In the dimension 50 H7, ‘H’ represents:23. विमा 50 H7 में, ‘H’ दर्शाता है: a) The type of fit / फिट का प्रकार b) The basic size / बेसिक साइज c) The fundamental deviation for the hole / छेद के लिए मौलिक विचलन d) The tolerance grade / टॉलरेंस ग्रेड 24. A drawing of a single spring is a type of:24. एक एकल स्प्रिंग का चित्र एक प्रकार है: a) Assembly drawing / असेंबली ड्राइंग b) Detail drawing / डिटेल ड्राइंग c) Schematic drawing / योजनाबद्ध ड्राइंग d) Exploded view / एक्सप्लोडेड व्यू 25. What is the final step after completing a drawing in CAD?25. CAD में एक ड्राइंग पूरा करने के बाद अंतिम चरण क्या है? a) Closing the software / सॉफ्टवेयर को बंद करना b) Deleting the file / फाइल को हटाना c) Saving the file / फाइल को सहेजना d) Starting a new drawing / एक नई ड्राइंग शुरू करना ← Previous Next → Finish Test / टेस्ट खत्म करें