ITI Draughtsman Mechanical 2nd Year Mock Test – 7 July 18, 2025 ITI Draughtsman Mechanical 2nd Year Mock Test – 7 | Instant Feedback ITI Draughtsman Mechanical 2nd Year Mock Test – 7 आईटीआई ड्राफ्ट्समैन मैकेनिकल द्वितीय वर्ष मॉक टेस्ट – 7 Time Left: 30:00 Test Complete! 1. In a drawing, the symbol ‘Ø’ indicates:1. एक ड्राइंग में, ‘Ø’ प्रतीक इंगित करता है: a) Radius / त्रिज्या b) Diameter / व्यास c) Depth / गहराई d) Angle / कोण 2. The part of a gear tooth between the pitch circle and the root circle is the:2. एक गियर के दांत का वह हिस्सा जो पिच सर्कल और रूट सर्कल के बीच होता है, वह है: a) Addendum / एडेंडम b) Dedendum / डिडेंडम c) Face / फेस d) Flank / फ्लैंक 3. A “transition fit” is one where the tolerance zones of the hole and shaft:3. एक “ट्रांजिशन फिट” वह है जिसमें छेद और शाफ्ट के टॉलरेंस जोन: a) Always result in a clearance / हमेशा एक क्लीयरेंस में परिणामित होते हैं b) Always result in an interference / हमेशा एक इंटरफेरेंस में परिणामित होते हैं c) Overlap / ओवरलैप करते हैं d) Have no relation / कोई संबंध नहीं रखते हैं 4. Which type of welding joint is formed when two pieces are placed edge to edge?4. किस प्रकार का वेल्डिंग जोड़ तब बनता है जब दो टुकड़े किनारे से किनारा मिलाकर रखे जाते हैं? a) Lap joint / लैप जॉइंट b) Tee joint / टी जॉइंट c) Butt joint / बट जॉइंट d) Corner joint / कॉर्नर जॉइंट 5. The main purpose of annealing a metal is to:5. एक धातु को एनीलिंग करने का मुख्य उद्देश्य है: a) Make it harder / इसे और कठोर बनाना b) Make it softer and relieve internal stresses / इसे नरम बनाना और आंतरिक तनाव को दूर करना c) Increase its brittleness / इसकी भंगुरता बढ़ाना d) Make it corrosion resistant / इसे संक्षारण प्रतिरोधी बनाना 6. The CAD command to create multiple copies of an object is:6. किसी वस्तु की कई प्रतियां बनाने के लिए CAD कमांड है: a) MOVE / मूव b) COPY / कॉपी c) OFFSET / ऑफसेट d) TRIM / ट्रिम 7. A template jig is a simple type of jig used for:7. एक टेम्पलेट जिग एक सरल प्रकार का जिग है जिसका उपयोग किया जाता है: a) High volume production / उच्च मात्रा में उत्पादन के लिए b) Guiding the tool for marking or drilling on flat plates / फ्लैट प्लेटों पर मार्किंग या ड्रिलिंग के लिए टूल का मार्गदर्शन करना c) Holding complex parts / जटिल भागों को पकड़ना d) Multi-spindle drilling / मल्टी-स्पिंडल ड्रिलिंग 8. The gear train used to get a large speed reduction is:8. एक बड़ी गति में कमी प्राप्त करने के लिए उपयोग किया जाने वाला गियर ट्रेन है: a) Simple gear train / सिंपल गियर ट्रेन b) Compound gear train / कंपाउंड गियर ट्रेन c) Worm and worm wheel / वर्म और वर्म व्हील d) Reverted gear train / रिवर्टेड गियर ट्रेन 9. A “GO” limit gauge should:9. एक “GO” लिमिट गेज को चाहिए: a) Go into or over the component being checked / जांचे जा रहे घटक के अंदर जाना या उसके ऊपर से गुजरना b) Not go into or over the component / घटक के अंदर नहीं जाना या उसके ऊपर से नहीं गुजरना c) Be used for rough checking only / केवल रफ जांच के लिए उपयोग किया जाना d) Be made of a soft material / एक नरम सामग्री का बना होना 10. The main purpose of a drawing is to:10. एक ड्राइंग का मुख्य उद्देश्य है: a) Be a piece of art / कला का एक नमूना होना b) Communicate all necessary information for manufacturing or assembly / निर्माण या असेंबली के लिए सभी आवश्यक जानकारी संप्रेषित करना c) Use as many colors as possible / यथासंभव कई रंगों का उपयोग करना d) Practice lettering / अक्षर-लेखन का अभ्यास करना 11. A ‘shaft basis system’ is one where the size of the _______ is kept constant.11. एक ‘शाफ्ट बेसिस सिस्टम’ वह है जहाँ _______ का आकार स्थिर रखा जाता है। a) Hole / छेद b) Shaft / शाफ्ट c) Both hole and shaft / छेद और शाफ्ट दोनों d) Neither hole nor shaft / न तो छेद और न ही शाफ्ट 12. A “NOT GO” gauge checks the:12. एक “नॉट गो” गेज जांचता है: a) Maximum material limit / अधिकतम सामग्री सीमा b) Minimum material limit / न्यूनतम सामग्री सीमा c) The basic size / बेसिक साइज d) The actual size / वास्तविक आकार 13. The CAD command to break a block into its individual parts is:13. एक ब्लॉक को उसके अलग-अलग भागों में तोड़ने के लिए CAD कमांड है: a) EXPLODE / एक्सप्लोड b) BREAK / ब्रेक c) TRIM / ट्रिम d) GROUP / ग्रुप 14. Tempering is done to:14. टेम्परिंग की जाती है: a) Increase hardness / कठोरता बढ़ाने के लिए b) Increase toughness and reduce brittleness / टफनेस बढ़ाने और भंगुरता कम करने के लिए c) Soften the metal / धातु को नरम करने के लिए d) Clean the surface / सतह को साफ करने के लिए 15. The ‘addendum’ of a gear tooth is the:15. एक गियर के दांत का ‘एडेंडम’ है: a) Radial distance from the pitch circle to the top of the tooth / पिच सर्कल से दांत के शीर्ष तक की रेडियल दूरी b) Radial distance from the pitch circle to the bottom of the tooth / पिच सर्कल से दांत के तल तक की रेडियल दूरी c) Width of the tooth / दांत की चौड़ाई d) Total height of the tooth / दांत की कुल ऊंचाई 16. The most important safety rule in a workshop is to:16. एक वर्कशॉप में सबसे महत्वपूर्ण सुरक्षा नियम है: a) Wear appropriate PPE and follow safety procedures / उपयुक्त पीपीई पहनना और सुरक्षा प्रक्रियाओं का पालन करना b) Work as fast as possible / जितनी जल्दी हो सके काम करना c) Use any tool available / किसी भी उपलब्ध उपकरण का उपयोग करना d) Keep the area messy / क्षेत्र को गंदा रखना 17. A drawing showing how parts fit together is an:17. एक ड्राइंग जो दिखाती है कि हिस्से एक साथ कैसे फिट होते हैं, वह है: a) Detail drawing / डिटेल ड्राइंग b) Assembly drawing / असेंबली ड्राइंग c) Part drawing / पार्ट ड्राइंग d) Schematic drawing / योजनाबद्ध ड्राइंग 18. The “3-2-1” principle is used to restrict how many degrees of freedom?18. “3-2-1” सिद्धांत का उपयोग स्वतंत्रता की कितनी डिग्री को प्रतिबंधित करने के लिए किया जाता है? a) 3 b) 6 c) 9 d) 12 19. In a welded joint, the throat thickness is the:19. एक वेल्डेड जोड़ में, थ्रोट की मोटाई है: a) Length of the weld / वेल्ड की लंबाई b) Shortest distance from the root to the face of a fillet weld / एक फिलेट वेल्ड की जड़ से चेहरे तक की सबसे छोटी दूरी c) Size of the weld leg / वेल्ड लेग का आकार d) Angle of the weld / वेल्ड का कोण 20. The symbol ‘V’ on a surface indicates:20. एक सतह पर ‘V’ प्रतीक इंगित करता है: a) The material type / सामग्री का प्रकार b) The surface roughness / सतह का खुरदरापन c) The direction of view / देखने की दिशा d) A welding symbol / एक वेल्डिंग प्रतीक 21. What is the main purpose of a fixture?21. एक फिक्स्चर का मुख्य उद्देश्य क्या है? a) To hold and locate a workpiece during machining / मशीनिंग के दौरान एक वर्कपीस को पकड़ना और पता लगाना b) To guide the cutting tool / कटिंग टूल का मार्गदर्शन करना c) To measure the final component / अंतिम घटक को मापना d) To cool the component / घटक को ठंडा करना 22. The gears used to change rotary motion into linear motion are:22. घूर्णी गति को रैखिक गति में बदलने के लिए उपयोग किए जाने वाले गियर हैं: a) Spur gears / स्पर गियर b) Bevel gears / बेवल गियर c) Worm and worm wheel / वर्म और वर्म व्हील d) Rack and pinion / रैक और पिनियन 23. In an assembly, if the shaft is smaller than the hole, it is a:23. एक असेंबली में, यदि शाफ्ट छेद से छोटा है, तो यह एक है: a) Interference fit / इंटरफेरेंस फिट b) Transition fit / ट्रांजिशन फिट c) Clearance fit / क्लीयरेंस फिट d) Push fit / पुश फिट 24. The heat treatment process of heating steel above its critical temperature and then cooling it slowly in the furnace is:24. स्टील को उसके महत्वपूर्ण तापमान से ऊपर गर्म करने और फिर उसे भट्ठी में धीरे-धीरे ठंडा करने की ऊष्मा उपचार प्रक्रिया है: a) Hardening / हार्डनिंग b) Tempering / टेम्परिंग c) Annealing / एनीलिंग d) Normalizing / नॉर्मलाइजिंग 25. What is the most important safety rule when using hand tools?25. हाथ के औजारों का उपयोग करते समय सबसे महत्वपूर्ण सुरक्षा नियम क्या है? a) Use the right tool for the right job / सही काम के लिए सही उपकरण का उपयोग करना b) Use the biggest tool available / उपलब्ध सबसे बड़े उपकरण का उपयोग करना c) Throw tools to a co-worker / एक सहकर्मी को औजार फेंकना d) Use a cheater bar for more force / अधिक बल के लिए एक चीटर बार का उपयोग करना ← Previous Next → Finish Test / टेस्ट खत्म करें