ITI Draughtsman Mechanical 2nd Year Mock Test – 4 July 17, 2025 ITI Draughtsman Mechanical 2nd Year Mock Test – 4 | Instant Feedback ITI Draughtsman Mechanical 2nd Year Mock Test – 4 आईटीआई ड्राफ्ट्समैन मैकेनिकल द्वितीय वर्ष मॉक टेस्ट – 4 Time Left: 30:00 Test Complete! 1. What is the primary purpose of a jig in manufacturing?1. विनिर्माण में एक जिग का प्राथमिक उद्देश्य क्या है? a) To only hold the workpiece / केवल वर्कपीस को पकड़ना b) To hold the workpiece and guide the cutting tool / वर्कपीस को पकड़ना और कटिंग टूल का मार्गदर्शन करना c) To only guide the cutting tool / केवल कटिंग टूल का मार्गदर्शन करना d) To measure the final product / अंतिम उत्पाद को मापना 2. An interference fit is one where the:2. एक इंटरफेरेंस फिट वह है जिसमें: a) Hole is always larger than the shaft / छेद हमेशा शाफ्ट से बड़ा होता है b) Shaft is always larger than the hole / शाफ्ट हमेशा छेद से बड़ा होता है c) Shaft and hole are of the same size / शाफ्ट और छेद एक ही आकार के होते हैं d) There is a large gap between mating parts / मेल खाने वाले भागों के बीच एक बड़ा गैप होता है 3. Which gauge is used to check the diameter of a hole?3. एक छेद का व्यास जांचने के लिए किस गेज का उपयोग किया जाता है? a) Ring Gauge / रिंग गेज b) Plug Gauge / प्लग गेज c) Feeler Gauge / फिलर गेज d) Thread Gauge / थ्रेड गेज 4. The term “tolerance” in engineering drawing refers to the:4. इंजीनियरिंग ड्राइंग में “टॉलरेंस” शब्द का अर्थ है: a) Exact dimension of a part / एक हिस्से का सटीक विमा b) Permissible variation in a dimension / एक विमा में अनुमेय भिन्नता c) Gap between two mating parts / दो मेल खाने वाले भागों के बीच का गैप d) Type of fit / फिट का प्रकार 5. What is the module of a gear?5. एक गियर का मॉड्यूल क्या है? a) Pitch Circle Diameter / Number of Teeth / पिच सर्कल व्यास / दांतों की संख्या b) Number of Teeth / Pitch Circle Diameter / दांतों की संख्या / पिच सर्कल व्यास c) Outside Diameter / Number of Teeth / बाहरी व्यास / दांतों की संख्या d) The number of teeth / दांतों की संख्या 6. The heat treatment process that makes steel softer and more ductile is:6. ऊष्मा उपचार की वह प्रक्रिया जो स्टील को नरम और अधिक तन्य बनाती है, वह है: a) Hardening / हार्डनिंग b) Tempering / टेम्परिंग c) Annealing / एनीलिंग d) Case hardening / केस हार्डनिंग 7. A “GO” gauge must:7. एक “GO” गेज को चाहिए: a) Enter the hole or pass over the shaft / छेद में प्रवेश करना या शाफ्ट के ऊपर से गुजरना b) Not enter the hole or not pass over the shaft / छेद में प्रवेश नहीं करना या शाफ्ट के ऊपर से नहीं गुजरना c) Be used for threading only / केवल थ्रेडिंग के लिए उपयोग किया जाना d) Check both limits simultaneously / दोनों सीमाओं की एक साथ जांच करना 8. The main purpose of a drilling jig is to:8. एक ड्रिलिंग जिग का मुख्य उद्देश्य है: a) Hold the workpiece and guide the drill bit / वर्कपीस को पकड़ना और ड्रिल बिट का मार्गदर्शन करना b) Only hold the workpiece / केवल वर्कपीस को पकड़ना c) Only guide the drill bit / केवल ड्रिल बिट का मार्गदर्शन करना d) Sharpen the drill bit / ड्रिल बिट को तेज करना 9. An exploded view drawing is used to show:9. एक एक्सप्लोडेड व्यू ड्राइंग का उपयोग दिखाने के लिए किया जाता है: a) The internal details of a part / एक हिस्से का आंतरिक विवरण b) The assembly sequence of parts / भागों का असेंबली अनुक्रम c) The dimensions of each part / प्रत्येक हिस्से की विमाएं d) A 2D view of the assembly / असेंबली का 2D व्यू 10. The distance between the tops of adjacent teeth on a gear is the:10. एक गियर पर आसन्न दांतों के शीर्षों के बीच की दूरी है: a) Circular pitch / सर्कुलर पिच b) Diametral pitch / डायमीट्रल पिच c) Module / मॉड्यूल d) Addendum / एडेंडम 11. A drawing that provides information for manufacturing a single part is a:11. एक ड्राइंग जो एक एकल हिस्से के निर्माण के लिए जानकारी प्रदान करती है, वह है: a) Assembly drawing / असेंबली ड्राइंग b) Detail drawing / डिटेल ड्राइंग c) Exploded view drawing / एक्सप्लोडेड व्यू ड्राइंग d) Schematic drawing / योजनाबद्ध ड्राइंग 12. A ‘shaft basis’ system of fits means that:12. फिट्स की ‘शाफ्ट बेसिस’ प्रणाली का मतलब है कि: a) The size of the hole is kept constant / छेद का आकार स्थिर रखा जाता है b) The upper deviation of the shaft is zero / शाफ्ट का ऊपरी विचलन शून्य होता है c) The fit is always an interference fit / फिट हमेशा एक इंटरफेरेंस फिट होता है d) Both sizes are varied / दोनों आकार भिन्न होते हैं 13. The CAD command to create a pattern of objects in rows and columns is:13. पंक्तियों और स्तंभों में वस्तुओं का एक पैटर्न बनाने के लिए CAD कमांड है: a) Rectangular Array / रेक्टेंगुलर ऐरे b) Polar Array / पोलर ऐरे c) COPY / कॉपी d) OFFSET / ऑफसेट 14. The property of a material to be drawn into wires is:14. किसी पदार्थ को तारों में खींचे जाने का गुण है: a) Malleability / आघातवर्धनीयता b) Elasticity / लोच c) Ductility / तन्यता d) Hardness / कठोरता 15. The purpose of a bearing is to:15. एक बेयरिंग का उद्देश्य है: a) Transmit power / शक्ति संचारित करना b) Join two parts / दो भागों को जोड़ना c) Support a rotating shaft and reduce friction / एक घूमने वाले शाफ्ट को सहारा देना और घर्षण कम करना d) Prevent rotation / घूर्णन को रोकना 16. The most common type of gear with teeth parallel to the axis of rotation is:16. घूर्णन की धुरी के समानांतर दांतों वाला सबसे आम प्रकार का गियर है: a) Spur gear / स्पर गियर b) Helical gear / हेलिकल गियर c) Bevel gear / बेवल गियर d) Worm gear / वर्म गियर 17. Which of these is a permanent joining process?17. इनमें से कौन एक स्थायी जोड़ने की प्रक्रिया है? a) Bolting / बोल्टिंग b) Screwing / स्क्रूइंग c) Welding / वेल्डिंग d) Using a key / एक की का उपयोग करना 18. The process of making steel less brittle after hardening is:18. हार्डनिंग के बाद स्टील को कम भंगुर बनाने की प्रक्रिया है: a) Annealing / एनीलिंग b) Tempering / टेम्परिंग c) Normalizing / नॉर्मलाइजिंग d) Spheroidizing / स्फेरोइडाइजिंग 19. In a limit gauge, the ‘GO’ end checks the:19. एक लिमिट गेज में, ‘GO’ सिरा जांचता है: a) Maximum material limit (e.g., minimum hole size) / अधिकतम सामग्री सीमा (जैसे, न्यूनतम छेद आकार) b) Minimum material limit (e.g., maximum hole size) / न्यूनतम सामग्री सीमा (जैसे, अधिकतम छेद आकार) c) The exact dimension / सटीक विमा d) The surface finish / सतह फिनिश 20. Which safety equipment must be worn when welding?20. वेल्डिंग करते समय कौन सा सुरक्षा उपकरण पहनना चाहिए? a) A hard hat / एक हार्ड हैट b) Welding helmet, gloves, and apron / वेल्डिंग हेलमेट, दस्ताने, और एप्रन c) Safety shoes / सुरक्षा जूते d) Earplugs / ईयरप्लग 21. The CAD command to create a circle is:21. एक वृत्त बनाने के लिए CAD कमांड है: a) CIRCLE / सर्कल b) ARC / आर्क c) ELLIPSE / एलिप्स d) LINE / लाइन 22. Gears that connect intersecting shafts are:22. प्रतिच्छेदी शाफ्टों को जोड़ने वाले गियर हैं: a) Spur gears / स्पर गियर b) Helical gears / हेलिकल गियर c) Worm gears / वर्म गियर d) Bevel gears / बेवल गियर 23. A jig bushing is used to:23. एक जिग बुशिंग का उपयोग किया जाता है: a) Accurately guide a drill or other cutting tool / एक ड्रिल या अन्य कटिंग टूल का सटीक मार्गदर्शन करने के लिए b) Hold the workpiece / वर्कपीस को पकड़ने के लिए c) Clamp the jig / जिग को क्लैंप करने के लिए d) Locate the fixture / फिक्स्चर का पता लगाने के लिए 24. The difference between the upper limit and the lower limit of a size is called:24. एक आकार की ऊपरी सीमा और निचली सीमा के बीच का अंतर कहलाता है: a) Allowance / एलाउंस b) Tolerance / टॉलरेंस c) Deviation / डेविएशन d) Fit / फिट 25. A drawing that gives dimensions and other information for every single part of an assembly is a(n):25. एक ड्राइंग जो एक असेंबली के प्रत्येक एकल भाग के लिए विमाएं और अन्य जानकारी देती है, वह है: a) Assembly drawing / असेंबली ड्राइंग b) Exploded view drawing / एक्सप्लोडेड व्यू ड्राइंग c) Detail drawing / डिटेल ड्राइंग d) Schematic drawing / योजनाबद्ध ड्राइंग ← Previous Next → Finish Test / टेस्ट खत्म करें