ITI Draughtsman Mechanical 1st Year Mock Test – 5 July 17, 2025 ITI Draughtsman Mechanical 1st Year Mock Test – 5 | Instant Feedback ITI Draughtsman Mechanical 1st Year Mock Test – 5 आईटीआई ड्राफ्ट्समैन मैकेनिकल प्रथम वर्ष मॉक टेस्ट – 5 Time Left: 30:00 Test Complete! 1. Which of the following pencil grades is the hardest?1. निम्नलिखित में से कौन सा पेंसिल ग्रेड सबसे कठोर है? a) HB b) 2B c) 4H d) F 2. In first-angle projection, the top view is placed:2. फर्स्ट-एंगल प्रोजेक्शन में, टॉप व्यू को रखा जाता है: a) Above the front view / फ्रंट व्यू के ऊपर b) Below the front view / फ्रंट व्यू के नीचे c) To the left of the front view / फ्रंट व्यू के बाईं ओर d) To the right of the front view / फ्रंट व्यू के दाईं ओर 3. A stud is a type of fastener which has:3. एक स्टड एक प्रकार का फास्टनर है जिसमें: a) A head on one end and threads on the other / एक सिरे पर एक सिर और दूसरे पर चूड़ियाँ होती हैं b) Threads on both ends / दोनों सिरों पर चूड़ियाँ होती हैं c) A pointed end / एक नुकीला सिरा होता है d) No threads / कोई चूड़ियाँ नहीं होती हैं 4. The primary first aid for a chemical splash in the eyes is to:4. आँखों में रासायनिक छींटे पड़ने पर प्राथमिक उपचार है: a) Rub the eyes vigorously / आँखों को जोर से रगड़ना b) Flush the eyes with plenty of clean water for 15-20 minutes / आँखों को 15-20 मिनट के लिए खूब सारे साफ पानी से धोना c) Apply a bandage / एक पट्टी लगाना d) Put eye drops / आई ड्रॉप डालना 5. In a drawing, hatching lines are used to indicate the:5. एक ड्राइंग में, हैचिंग लाइनों का उपयोग इंगित करने के लिए किया जाता है: a) Center of the object / वस्तु का केंद्र b) Part of the object that has been cut / वस्तु का वह हिस्सा जिसे काटा गया है c) Outline of the object / वस्तु की रूपरेखा d) Hidden part of the object / वस्तु का छिपा हुआ हिस्सा 6. The CAD command to reverse the last action is:6. पिछली कार्रवाई को उलटने के लिए CAD कमांड है: a) DELETE / डिलीट b) REDO / रीडू c) UNDO / अनडू d) BACK / बैक 7. Which of the following is a non-ferrous metal?7. निम्नलिखित में से कौन सी एक अलौह धातु है? a) Mild Steel / माइल्ड स्टील b) Cast Iron / कच्चा लोहा c) High Carbon Steel / उच्च कार्बन स्टील d) Aluminum / एल्यूमीनियम 8. A reducing scale is one where the R.F. is:8. एक छोटा करने वाला पैमाना वह है जहां R.F. है: a) Greater than 1 / 1 से अधिक b) Equal to 1 / 1 के बराबर c) Less than 1 / 1 से कम d) Zero / शून्य 9. A line drawn tangent to a circle at a point is _______ to the radius at that point.9. एक बिंदु पर एक वृत्त पर खींची गई एक स्पर्शरेखा उस बिंदु पर त्रिज्या के _______ होती है। a) Parallel / समानांतर b) Perpendicular / लंबवत c) At 45 degrees / 45 डिग्री पर d) Collinear / संरेख 10. A key is a machine element used to:10. एक की (key) एक मशीन तत्व है जिसका उपयोग किया जाता है: a) Lock a door / एक दरवाजा बंद करने के लिए b) Prevent relative rotation between a shaft and a hub / एक शाफ्ट और एक हब के बीच सापेक्ष घूर्णन को रोकने के लिए c) Open a lock / एक ताला खोलने के लिए d) Join two wires / दो तारों को जोड़ने के लिए 11. An isometric drawing provides a:11. एक आइसोमेट्रिक ड्राइंग प्रदान करता है: a) 2D view / 2D व्यू b) Sectional view / सेक्शनल व्यू c) Pictorial (3D) view / चित्रात्मक (3D) व्यू d) Top view only / केवल टॉप व्यू 12. For a symmetrical object, which type of section is used to show both internal and external features in a single view?12. एक सममित वस्तु के लिए, एक ही दृश्य में आंतरिक और बाहरी दोनों विशेषताओं को दिखाने के लिए किस प्रकार के सेक्शन का उपयोग किया जाता है? a) Full section / फुल सेक्शन b) Offset section / ऑफसेट सेक्शन c) Half section / हाफ सेक्शन d) Revolved section / रिवॉल्व्ड सेक्शन 13. A divider is used for:13. एक डिवाइडर का उपयोग किया जाता है: a) Drawing circles / वृत्त बनाने के लिए b) Measuring angles / कोण मापने के लिए c) Transferring dimensions and dividing lines / विमाओं को स्थानांतरित करने और रेखाओं को विभाजित करने के लिए d) Drawing parallel lines / समानांतर रेखाएं खींचने के लिए 14. The property of a material to withstand shock or impact loads is:14. झटके या प्रभाव भार का सामना करने के लिए किसी सामग्री का गुण है: a) Hardness / कठोरता b) Brittleness / भंगुरता c) Toughness / टफनेस d) Elasticity / लोच 15. The head of a rivet for structural steel work is typically a:15. संरचनात्मक स्टील के काम के लिए एक रिवेट का सिर आमतौर पर होता है: a) Snap head / स्नैप हेड b) Countersunk head / काउंटरसंक हेड c) Flat head / फ्लैट हेड d) Conical head / कोनिकल हेड 16. A Class C fire involves:16. एक क्लास C की आग में शामिल हैं: a) Combustible metals / ज्वलनशील धातुएं b) Flammable liquids / ज्वलनशील तरल पदार्थ c) Energized electrical equipment / सक्रिय विद्युत उपकरण d) Wood and paper / लकड़ी और कागज 17. In which dimensioning system are all texts placed so they can be read from the bottom of the sheet?17. किस विमांकन प्रणाली में सभी टेक्स्ट इस तरह रखे जाते हैं कि उन्हें शीट के नीचे से पढ़ा जा सके? a) Aligned system / अलाइन्ड सिस्टम b) Unidirectional system / यूनिडायरेक्शनल सिस्टम c) Parallel dimensioning / पैरेलल विमांकन d) Chain dimensioning / चेन विमांकन 18. The front view of a cube resting on one of its faces on the H.P. is a:18. H.P. पर अपने एक फलक पर टिके हुए एक घन का फ्रंट व्यू है: a) Square / एक वर्ग b) Rectangle / एक आयत c) Circle / एक वृत्त d) Triangle / एक त्रिभुज 19. The internal threads in a nut are cut using a:19. एक नट में आंतरिक चूड़ियाँ किसका उपयोग करके काटी जाती हैं: a) Die / एक डाई b) Tap / एक टैप c) Reamer / एक रीमर d) Drill / एक ड्रिल 20. High Carbon Steel is used for making:20. उच्च कार्बन स्टील का उपयोग बनाने के लिए किया जाता है: a) Machine bodies / मशीन बॉडीज b) Cutting tools like chisels and files / छेनी और फाइल जैसे कटिंग टूल्स c) Nuts and bolts / नट और बोल्ट d) Shafts / शाफ्ट 21. The symbol ‘R’ before a dimension indicates:21. एक विमा से पहले ‘R’ प्रतीक इंगित करता है: a) Radius / त्रिज्या b) Diameter / व्यास c) Repetition / पुनरावृत्ति d) Roundness / गोलाई 22. Which of these is a permanent fastening method?22. इनमें से कौन एक स्थायी बन्धन विधि है? a) Bolting / बोल्टिंग b) Screwing / स्क्रूइंग c) Welding / वेल्डिंग d) Pinning / पिनिंग 23. In orthographic projection, the projectors are _______ to the plane of projection.23. ऑर्थोग्राफिक प्रोजेक्शन में, प्रोजेक्टर प्रोजेक्शन के तल के _______ होते हैं। a) Parallel / समानांतर b) Perpendicular / लंबवत c) Inclined / झुके हुए d) At 45 degrees / 45 डिग्री पर 24. Which of these materials is known for being lightweight and having good corrosion resistance?24. इनमें से कौन सी सामग्री हल्की और अच्छे संक्षारण प्रतिरोध के लिए जानी जाती है? a) Cast Iron / कच्चा लोहा b) Mild Steel / माइल्ड स्टील c) Aluminum / एल्यूमीनियम d) High Carbon Steel / उच्च कार्बन स्टील 25. The main purpose of a drawing board is to provide a:25. एक ड्राइंग बोर्ड का मुख्य उद्देश्य प्रदान करना है: a) Place to store pencils / पेंसिल स्टोर करने की जगह b) Hard surface for drawing / ड्राइंग के लिए एक कठोर सतह c) Flat and smooth surface for drawing on paper / कागज पर ड्राइंग के लिए एक सपाट और चिकनी सतह d) Surface to cut paper / कागज काटने के लिए एक सतह ← Previous Next → Finish Test / टेस्ट खत्म करें