ITI Turner 1st Year Mock Test – 4 July 16, 2025 ITI Turner 1st Year Mock Test – 4 | Instant Feedback ITI Turner 1st Year Mock Test – 4 आईटीआई टर्नर प्रथम वर्ष मॉक टेस्ट – 4 Time Left: 30:00 Test Complete! 1. The acronym PASS for operating a fire extinguisher stands for:1. अग्निशामक यंत्र चलाने के लिए PASS का संक्षिप्त नाम है: a) Push, Aim, Squeeze, Spray / पुश, एम, स्क्वीज, स्प्रे b) Pull, Aim, Squeeze, Sweep / पुल, एम, स्क्वीज, स्वीप c) Pass, Alert, Shout, Secure / पास, अलर्ट, शाउट, सिक्योर d) Pull, Assess, Spray, Stop / पुल, एसेस, स्प्रे, स्टॉप 2. The correct formula for calculating lathe spindle RPM is:2. लेथ स्पिंडल RPM की गणना के लिए सही सूत्र है: a) RPM = (Cutting Speed × Diameter) / 1000 b) RPM = (π × Diameter × 1000) / Cutting Speed c) RPM = (Cutting Speed × 1000) / (π × Diameter) d) RPM = Diameter / (Cutting Speed × 1000) 3. The least count of a measuring instrument refers to:3. एक मापने वाले उपकरण का अल्पतमांक (least count) संदर्भित करता है: a) The largest measurement it can take / सबसे बड़ा माप जो वह ले सकता है b) The smallest measurement that can be accurately read / सबसे छोटा माप जिसे सटीक रूप से पढ़ा जा सकता है c) The total length of its scale / इसके पैमाने की कुल लंबाई d) The accuracy error of the instrument / उपकरण की सटीकता त्रुटि 4. For correct filing technique, pressure should be applied on the file during:4. सही फाइलिंग तकनीक के लिए, फाइल पर दाब कब लगाया जाना चाहिए: a) The forward stroke only / केवल फॉरवर्ड स्ट्रोक के दौरान b) The return stroke only / केवल रिटर्न स्ट्रोक के दौरान c) Both forward and return strokes / फॉरवर्ड और रिटर्न दोनों स्ट्रोक के दौरान d) The middle of the stroke / स्ट्रोक के बीच में 5. The thread chasing dial on a lathe is used to:5. लेथ पर थ्रेड चेज़िंग डायल का उपयोग किया जाता है: a) Measure the pitch of the thread / चूड़ी की पिच को मापने के लिए b) Select the speed for thread cutting / चूड़ी काटने के लिए गति का चयन करने के लिए c) Engage the half-nut at the correct point for cutting a thread / चूड़ी काटने के लिए सही बिंदु पर हाफ-नट को संलग्न करने के लिए d) Set the depth of the thread / चूड़ी की गहराई सेट करने के लिए 6. Which of the following is a non-ferrous metal?6. निम्नलिखित में से कौन सी एक अलौह धातु है? a) Mild Steel / माइल्ड स्टील b) Cast Iron / कच्चा लोहा c) High Carbon Steel / उच्च कार्बन स्टील d) Aluminum / एल्यूमीनियम 7. The primary advantage of a four-jaw independent chuck is its ability to:7. एक फोर-जॉ इंडिपेंडेंट चक का प्राथमिक लाभ इसकी क्षमता है: a) Center round jobs quickly / गोल जॉब को जल्दी से केंद्रित करना b) Hold irregular, square, or hexagonal jobs accurately / अनियमित, चौकोर, या षट्कोणीय जॉब को सटीकता से पकड़ना c) Hold very small jobs / बहुत छोटे जॉब को पकड़ना d) Operate at higher speeds than a three-jaw chuck / थ्री-जॉ चक की तुलना में उच्च गति पर काम करना 8. Carbide tipped tools are used on lathes because they:8. लेथ पर कार्बाइड टिप्ड टूल्स का उपयोग किया जाता है क्योंकि वे: a) Are cheaper than HSS tools / HSS टूल्स से सस्ते होते हैं b) Can be re-sharpened more easily / अधिक आसानी से फिर से तेज किए जा सकते हैं c) Can withstand higher temperatures and allow for higher cutting speeds / उच्च तापमान का सामना कर सकते हैं और उच्च कटिंग स्पीड की अनुमति देते हैं d) Are softer than HSS tools / HSS टूल्स से नरम होते हैं 9. To align the tailstock for parallel turning, one method uses a test bar and a:9. समानांतर टर्निंग के लिए टेलस्टॉक को संरेखित करने के लिए, एक विधि एक टेस्ट बार और एक का उपयोग करती है: a) Steel rule / स्टील रूल b) Try square / ट्राई स्क्वायर c) Dial test indicator / डायल टेस्ट इंडिकेटर d) Scriber / स्क्राइबर 10. The operation of cutting a narrow groove on a workpiece is called:10. एक वर्कपीस पर एक संकीर्ण खांचा काटने की प्रक्रिया कहलाती है: a) Chamfering / चैम्फरिंग b) Knurling / नर्लिंग c) Grooving or Necking / ग्रूविंग या नेकिंग d) Facing / फेसिंग 11. A ring spanner provides a better grip than an open-ended spanner because it:11. एक रिंग स्पैनर एक ओपन-एंडेड स्पैनर की तुलना में बेहतर पकड़ प्रदान करता है क्योंकि यह: a) Is longer / लंबा होता है b) Is heavier / भारी होता है c) Surrounds the nut or bolt head on all sides / नट या बोल्ट के सिर को सभी तरफ से घेरता है d) Is made of a harder material / एक कठोर सामग्री से बना होता है 12. The quill of the tailstock is moved in and out by rotating the:12. टेलस्टॉक का क्विल किसके द्वारा घुमाकर अंदर और बाहर किया जाता है: a) Chuck key / चक की b) Tailstock handwheel / टेलस्टॉक हैंडव्हील c) Carriage handwheel / कैरिज हैंडव्हील d) Spindle speed lever / स्पिंडल स्पीड लीवर 13. A smaller hole drilled before a larger drill bit is used is called a:13. एक बड़े ड्रिल बिट का उपयोग करने से पहले ड्रिल किया गया एक छोटा छेद कहलाता है: a) Pilot hole / पायलट होल b) Reamed hole / रीम्ड होल c) Bored hole / बोर किया हुआ होल d) Blind hole / ब्लाइंड होल 14. The lathe operation used to cut a workpiece into two pieces is called:14. एक वर्कपीस को दो टुकड़ों में काटने के लिए उपयोग की जाने वाली लेथ प्रक्रिया कहलाती है: a) Facing / फेसिंग b) Parting-off / पार्टिंग-ऑफ c) Grooving / ग्रूविंग d) Knurling / नर्लिंग 15. When handling tools with sharp edges, you should:15. तेज किनारों वाले उपकरणों को संभालते समय, आपको चाहिए: a) Throw them to a coworker / उन्हें एक सहकर्मी को फेंकें b) Carry them with the sharp edge pointing downwards and away from your body / उन्हें तेज किनारे को नीचे और अपने शरीर से दूर रखते हुए ले जाएं c) Keep them in your pocket / उन्हें अपनी जेब में रखें d) Carry many sharp tools at once / एक साथ कई तेज उपकरण ले जाएं 16. Why is it important to balance a grinding wheel before using it?16. उपयोग करने से पहले एक ग्राइंडिंग व्हील को संतुलित करना क्यों महत्वपूर्ण है? a) To make it look centered / इसे केंद्रित दिखाने के लिए b) To prevent vibration, ensure good surface finish, and for safety / कंपन को रोकने, अच्छी सतह फिनिश सुनिश्चित करने, और सुरक्षा के लिए c) To make the wheel grind faster / व्हील को तेजी से पीसने के लिए d) It is not important to balance a grinding wheel / एक ग्राइंडिंग व्हील को संतुलित करना महत्वपूर्ण नहीं है 17. Quenching is the process of:17. क्वेंचिंग प्रक्रिया है: a) Slowly cooling a heated metal / एक गर्म धातु को धीरे-धीरे ठंडा करना b) Rapidly cooling a heated metal, usually to harden it / एक गर्म धातु को तेजी से ठंडा करना, आमतौर पर इसे कठोर करने के लिए c) Heating a metal to just below its melting point / एक धातु को उसके गलनांक के ठीक नीचे तक गर्म करना d) Cleaning a metal with water / एक धातु को पानी से साफ करना 18. A built-up edge (BUE) on a cutting tool is more likely to form when:18. एक कटिंग टूल पर एक बिल्ट-अप एज (BUE) बनने की अधिक संभावना होती है जब: a) Machining brittle materials at high speeds / उच्च गति पर भंगुर सामग्री की मशीनिंग b) Machining ductile materials at low speeds / कम गति पर तन्य सामग्री की मशीनिंग c) Using a very sharp tool / एक बहुत तेज टूल का उपयोग करना d) Using a coolant / एक कूलेंट का उपयोग करना 19. The gears that connect the spindle to the lead screw are called:19. स्पिंडल को लीड स्क्रू से जोड़ने वाले गियर कहलाते हैं: a) Tumbler gears / टम्बलर गियर b) Change gears / चेंज गियर c) Bevel gears / बेवल गियर d) Worm gears / वर्म गियर 20. A surface plate is used in a workshop as a:20. एक वर्कशॉप में एक सरफेस प्लेट का उपयोग किया जाता है: a) Place to hold heavy jobs / भारी जॉब रखने की जगह के रूप में b) Precise flat reference surface for marking and inspection / मार्किंग और निरीक्षण के लिए एक सटीक सपाट संदर्भ सतह के रूप में c) Cutting surface / काटने की सतह के रूप में d) Heat treatment surface / ऊष्मा उपचार सतह के रूप में 21. The property of a material to absorb energy and deform plastically without fracturing is:21. किसी पदार्थ का वह गुण जो ऊर्जा को अवशोषित करने और बिना टूटे प्लास्टिक रूप से विकृत होने की अनुमति देता है, वह है: a) Hardness / कठोरता b) Brittleness / भंगुरता c) Toughness / टफनेस (चिमड़ापन) d) Stiffness / स्टिफनेस (कड़ापन) 22. If D=50mm, d=40mm, and the length of the taper (l) is 100mm, what is the taper ratio (K)?22. यदि D=50मिमी, d=40मिमी, और टेपर की लंबाई (l) 100मिमी है, तो टेपर अनुपात (K) क्या है? a) 1:5 b) 1:20 c) 1:10 d) 1:2 23. Before starting any machine, a good safety practice is to:23. किसी भी मशीन को शुरू करने से पहले, एक अच्छी सुरक्षा प्रथा है: a) Ensure all safety guards are in place and the work area is clear / यह सुनिश्चित करना कि सभी सुरक्षा गार्ड अपनी जगह पर हैं और कार्य क्षेत्र साफ है b) Shout loudly / जोर से चिल्लाना c) Check the time / समय की जांच करना d) Have a drink of water / पानी पीना 24. Which type of hammer has one flat face and one round, hemispherical face?24. किस प्रकार के हथौड़े में एक सपाट चेहरा और एक गोल, अर्धगोलाकार चेहरा होता है? a) Claw hammer / क्लॉ हैमर b) Sledge hammer / स्लेज हैमर c) Ball-peen hammer / बॉल-पीन हैमर d) Mallet / मैलेट 25. The gears located in the apron of the lathe carriage are primarily for:25. लेथ कैरिज के एप्रन में स्थित गियर मुख्य रूप से हैं: a) Changing the spindle speed / स्पिंडल की गति बदलने के लिए b) Providing power movement to the carriage and cross-slide / कैरिज और क्रॉस-स्लाइड को शक्ति आंदोलन प्रदान करने के लिए c) Holding the cutting tool / कटिंग टूल को पकड़ने के लिए d) Thread cutting only / केवल चूड़ी काटने के लिए ← Previous Next → Finish Test / टेस्ट खत्म करें