ITI MRAC 2nd Year Mock Test – 10 July 16, 2025 ITI MRAC 2nd Year Mock Test – 10 | Instant Feedback ITI MRAC 2nd Year Mock Test – 10 आईटीआई एमआरएसी द्वितीय वर्ष मॉक टेस्ट – 10 Time Left: 30:00 Test Complete! 1. When commissioning a new system, a “pre-functional checklist” is used to:1. एक नए सिस्टम को चालू करते समय, एक “प्री-फंक्शनल चेकलिस्ट” का उपयोग किया जाता है: a) Test the final performance of the system / सिस्टम के अंतिम प्रदर्शन का परीक्षण करने के लिए b) Verify components are installed correctly before system startup / सिस्टम शुरू करने से पहले यह सत्यापित करने के लिए कि घटक सही ढंग से स्थापित हैं c) Calculate the total cost of the project / परियोजना की कुल लागत की गणना करने के लिए d) Order spare parts / स्पेयर पार्ट्स ऑर्डर करने के लिए 2. A running compressor with high head pressure, low suction pressure, and high superheat strongly indicates:2. उच्च हेड प्रेशर, निम्न सक्शन प्रेशर और उच्च सुपरहीट के साथ चल रहा एक कंप्रेसर दृढ़ता से इंगित करता है: a) A severe restriction in the system (e.g., clogged filter drier) / सिस्टम में एक गंभीर प्रतिबंध (जैसे, बंद फिल्टर ड्रायर) b) Refrigerant overcharge / रेफ्रिजरेंट ओवरचार्ज c) A faulty compressor with bad valves / खराब वाल्व वाला एक दोषपूर्ण कंप्रेसर d) Non-condensable gases in the system / सिस्टम में गैर-संघननशील गैसें 3. On a psychrometric chart, the process of heating and humidifying air moves:3. एक साइकोमेट्रिक चार्ट पर, हवा को गर्म करने और आर्द्र करने की प्रक्रिया चलती है: a) Down and to the left / नीचे और बाईं ओर b) Horizontally to the right / क्षैतिज रूप से दाईं ओर c) Up and to the right / ऊपर और दाईं ओर d) Vertically down / लंबवत रूप से नीचे 4. A flow switch on a chiller’s evaporator barrel is a safety device that:4. एक चिलर के इवैपोरेटर बैरल पर एक फ्लो स्विच एक सुरक्षा उपकरण है जो: a) Ensures water is flowing before allowing the compressor to start / कंप्रेसर को शुरू करने की अनुमति देने से पहले यह सुनिश्चित करता है कि पानी बह रहा है b) Measures the refrigerant flow rate / रेफ्रिजरेंट प्रवाह दर को मापता है c) Shuts down the system if the water is too warm / यदि पानी बहुत गर्म हो तो सिस्टम को बंद कर देता है d) Controls the speed of the water pump / पानी के पंप की गति को नियंत्रित करता है 5. If a VRF system displays a communication error, the first thing to check is the:5. यदि एक VRF प्रणाली एक संचार त्रुटि प्रदर्शित करती है, तो जांचने वाली पहली चीज है: a) Refrigerant charge / रेफ्रिजरेंट चार्ज b) Main power supply voltage / मुख्य बिजली आपूर्ति वोल्टेज c) Communication wiring between indoor and outdoor units / इनडोर और आउटडोर इकाइयों के बीच संचार वायरिंग d) Air filters / एयर फिल्टर 6. To accurately check a car’s AC performance, you should measure:6. एक कार की एसी के प्रदर्शन की सटीक जांच करने के लिए, आपको मापना चाहिए: a) The temperature of the tires / टायरों का तापमान b) The temperature of the air coming from the center vent and the ambient air temperature / केंद्र वेंट से आने वाली हवा का तापमान और परिवेशी वायु का तापमान c) The engine coolant temperature / इंजन कूलेंट का तापमान d) The speed of the car / कार की गति 7. Regular cleaning of condenser coils on a commercial refrigerator is important because:7. एक वाणिज्यिक रेफ्रिजरेटर पर कंडेनसर कॉइल्स की नियमित सफाई महत्वपूर्ण है क्योंकि: a) It makes the unit look clean / यह इकाई को साफ दिखाता है b) It improves heat rejection, reduces head pressure, and saves energy / यह ऊष्मा अस्वीकृति में सुधार करता है, हेड प्रेशर कम करता है, और ऊर्जा बचाता है c) It is required by law, but does not affect performance / यह कानून द्वारा आवश्यक है, लेकिन प्रदर्शन को प्रभावित नहीं करता है d) It makes the unit run quieter / यह इकाई को शांत चलाता है 8. When installing ductwork, all transverse joints (connections) should be sealed with:8. डक्टवर्क स्थापित करते समय, सभी अनुप्रस्थ जोड़ों (कनेक्शन) को सील किया जाना चाहिए: a) Regular transparent tape / नियमित पारदर्शी टेप से b) Mastic sealant or approved foil tape / मैस्टिक सीलेंट या अनुमोदित फॉइल टेप से c) Nothing, they are self-sealing / कुछ भी नहीं, वे स्वयं-सीलिंग होते हैं d) Silicone caulk / सिलिकॉन कॉक से 9. Which of the following is an effective Energy Conservation Measure (ECM) for HVAC?9. निम्नलिखित में से कौन सा एचवीएसी के लिए एक प्रभावी ऊर्जा संरक्षण उपाय (ECM) है? a) Setting the thermostat to the lowest possible temperature / थर्मोस्टेट को सबसे कम संभव तापमान पर सेट करना b) Never cleaning the air filters / एयर फिल्टर को कभी साफ नहीं करना c) Regularly cleaning coils, changing filters, and ensuring proper refrigerant charge / नियमित रूप से कॉइल्स की सफाई, फिल्टर बदलना, और उचित रेफ्रिजरेंट चार्ज सुनिश्चित करना d) Blocking air vents with furniture / एयर वेंट को फर्नीचर से ब्लॉक करना 10. A BMS can improve a building’s efficiency by:10. एक BMS एक भवन की दक्षता में सुधार कर सकता है: a) Making the lights brighter / रोशनी को और तेज करके b) Implementing advanced strategies like occupancy scheduling / अधिभोग समय-निर्धारण जैसी उन्नत रणनीतियों को लागू करके c) Increasing the building’s temperature / भवन का तापमान बढ़ाकर d) Only by controlling the security system / केवल सुरक्षा प्रणाली को नियंत्रित करके 11. A high “approach” temperature in a cooling tower indicates:11. एक कूलिंग टॉवर में एक उच्च “एप्रोच” तापमान इंगित करता है: a) Excellent performance / उत्कृष्ट प्रदर्शन b) Poor performance (the tower is not cooling water effectively) / खराब प्रदर्शन (टॉवर पानी को प्रभावी ढंग से ठंडा नहीं कर रहा है) c) The water level is too high / पानी का स्तर बहुत अधिक है d) The fan is running too fast / पंखा बहुत तेज चल रहा है 12. The main difference between a centrifugal fan and an axial fan is the:12. एक सेंट्रीफ्यूगल पंखे और एक एक्सियल पंखे के बीच मुख्य अंतर है: a) Number of blades / ब्लेड की संख्या b) Direction of airflow relative to the fan shaft / पंखे के शाफ्ट के सापेक्ष वायु प्रवाह की दिशा c) Material they are made from / जिस सामग्री से वे बने हैं d) Color of the fan / पंखे का रंग 13. In an absorption chiller, the “generator” is where:13. एक अवशोषण चिलर में, “जनरेटर” वह जगह है जहाँ: a) Electricity is produced / बिजली का उत्पादन होता है b) A heat source boils refrigerant out of an absorbent solution / एक ऊष्मा स्रोत एक अवशोषक घोल से रेफ्रिजरेंट को उबालता है c) The refrigerant is compressed mechanically / रेफ्रिजरेंट को यांत्रिक रूप से संपीड़ित किया जाता है d) Chilled water is produced / ठंडा पानी बनाया जाता है 14. A VAV (Variable Air Volume) system saves energy primarily by:14. एक VAV (वेरिएबल एयर वॉल्यूम) प्रणाली मुख्य रूप से ऊर्जा बचाती है: a) Using a more efficient refrigerant / एक अधिक कुशल रेफ्रिजरेंट का उपयोग करके b) Reducing fan speed and airflow when cooling demand is low / जब कूलिंग की मांग कम हो तो पंखे की गति और वायु प्रवाह को कम करके c) Turning off the lights in the room / कमरे की रोशनी बंद करके d) Using thicker duct insulation / मोटे डक्ट इन्सुलेशन का उपयोग करके 15. A technician measures 0 Volts at the compressor terminals, but 24 Volts at the contactor coil. The problem is likely:15. एक तकनीशियन कंप्रेसर टर्मिनलों पर 0 वोल्ट मापता है, लेकिन कॉन्टैक्टर कॉइल पर 24 वोल्ट। समस्या की संभावना है: a) A faulty compressor motor / एक खराब कंप्रेसर मोटर b) A faulty thermostat / एक खराब थर्मोस्टेट c) The contactor’s power contacts have failed or there is a problem with the line voltage supply / कॉन्टैक्टर के पावर संपर्क विफल हो गए हैं या लाइन वोल्टेज आपूर्ति में कोई समस्या है d) The contactor coil is open / कॉन्टैक्टर कॉइल ओपन है 16. The “bypass factor” of a cooling coil relates to:16. एक कूलिंग कॉइल का “बाईपास फैक्टर” संबंधित है: a) The amount of refrigerant bypassing the coil / कॉइल को बाईपास करने वाले रेफ्रिजरेंट की मात्रा b) The fraction of air that passes through the coil without being cooled / हवा का वह अंश जो ठंडा हुए बिना कॉइल से गुजरता है c) A special valve that bypasses the coil / एक विशेष वाल्व जो कॉइल को बाईपास करता है d) The efficiency of the fan motor / पंखे की मोटर की दक्षता 17. What is a “cold storage” facility primarily used for?17. एक “कोल्ड स्टोरेज” सुविधा का उपयोग मुख्य रूप से किस लिए किया जाता है? a) Storing office documents / कार्यालय के दस्तावेजों का भंडारण करना b) Preserving perishable items like food and medicines at low temperatures / खराब होने वाली वस्तुओं जैसे भोजन और दवाओं को कम तापमान पर संरक्षित करना c) As a comfortable place to work in summer / गर्मियों में काम करने के लिए एक आरामदायक जगह के रूप में d) Storing warm items / गर्म वस्तुओं का भंडारण करना 18. The process of verifying that all system components operate together as designed is:18. यह सत्यापित करने की प्रक्रिया कि सभी सिस्टम घटक डिज़ाइन के अनुसार एक साथ काम करते हैं: a) Retrofitting / रेट्रोफिटिंग b) Functional performance testing (part of commissioning) / कार्यात्मक प्रदर्शन परीक्षण (कमीशनिंग का हिस्सा) c) Duct cleaning / डक्ट की सफाई d) Brazing / ब्रेज़िंग 19. What does a high superheat reading generally indicate about the evaporator?19. एक उच्च सुपरहीट रीडिंग आम तौर पर इवैपोरेटर के बारे में क्या इंगित करती है? a) It is flooded with liquid refrigerant / यह तरल रेफ्रिजरेंट से भरा हुआ है b) It is starved of refrigerant (not getting enough liquid) / इसमें रेफ्रिजरेंट की कमी है (पर्याप्त तरल नहीं मिल रहा है) c) It is working perfectly / यह पूरी तरह से काम कर रहा है d) It is blocked with ice / यह बर्फ से अवरुद्ध है 20. An economizer on a rooftop unit allows the system to:20. एक रूफटॉप इकाई पर एक इकोनोमाइज़र सिस्टम को यह करने की अनुमति देता है: a) Use cool, dry outside air for cooling instead of mechanical refrigeration / यांत्रिक प्रशीतन के बजाय ठंडा करने के लिए ठंडी, सूखी बाहरी हवा का उपयोग करना b) Run the compressor more efficiently / कंप्रेसर को अधिक कुशलता से चलाना c) Heat the building in winter / सर्दियों में इमारत को गर्म करना d) Save water / पानी बचाना 21. The most important safety step before performing any work on an electrical circuit is to:21. किसी भी विद्युत सर्किट पर कोई भी काम करने से पहले सबसे महत्वपूर्ण सुरक्षा कदम है: a) Wear clean clothes / साफ कपड़े पहनना b) Tell a coworker what you are doing / एक सहकर्मी को बताना कि आप क्या कर रहे हैं c) De-energize, lock out, tag out, and verify the circuit is dead / सर्किट को डी-एनर्जाइज़, लॉक आउट, टैग आउट करना और सत्यापित करना कि वह बंद है d) Put on safety glasses / सुरक्षा चश्मा पहनना 22. Which component is responsible for changing the direction of refrigerant flow in a heat pump?22. एक हीट पंप में रेफ्रिजरेंट प्रवाह की दिशा बदलने के लिए कौन सा घटक जिम्मेदार है? a) The compressor / कंप्रेसर b) The reversing valve / रिवर्सिंग वाल्व c) The thermostat / थर्मोस्टेट d) The expansion valve / विस्तार वाल्व 23. In an absorption refrigeration system, a heat source is used instead of a:23. एक अवशोषण प्रशीतन प्रणाली में, इसके बजाय एक ऊष्मा स्रोत का उपयोग किया जाता है: a) Condenser / कंडेनसर b) Mechanical Compressor / यांत्रिक कंप्रेसर c) Evaporator / इवैपोरेटर d) Expansion Valve / विस्तार वाल्व 24. What is the purpose of duct insulation?24. डक्ट इन्सुलेशन का उद्देश्य क्या है? a) To make the duct stronger / डक्ट को मजबूत बनाना b) To prevent heat loss/gain and control condensation / ऊष्मा हानि/लाभ को रोकना और संघनन को नियंत्रित करना c) To make the duct quieter / डक्ट को शांत बनाना d) To make the duct look better / डक्ट को बेहतर दिखाना 25. A scroll compressor is a type of:25. एक स्क्रॉल कंप्रेसर एक प्रकार है: a) Centrifugal compressor / सेंट्रीफ्यूगल कंप्रेसर का b) Positive displacement compressor / पॉजिटिव डिस्प्लेसमेंट कंप्रेसर का c) Axial compressor / एक्सियल कंप्रेसर का d) Ejector compressor / इजेक्टर कंप्रेसर का ← Previous Next → Finish Test / टेस्ट खत्म करें