ITI MRAC 2nd Year Mock Test – 7 July 16, 2025 ITI MRAC 2nd Year Mock Test – 7 | Instant Feedback ITI MRAC 2nd Year Mock Test – 7 आईटीआई एमआरएसी द्वितीय वर्ष मॉक टेस्ट – 7 Time Left: 30:00 Test Complete! 1. When brazing copper to steel, which type of filler metal is often used?1. तांबे को स्टील से ब्रेज़िंग करते समय, अक्सर किस प्रकार की भराव धातु का उपयोग किया जाता है? a) A copper-phosphorus alloy / एक कॉपर-फॉस्फोरस मिश्र धातु b) A high silver-content alloy / एक उच्च चांदी-सामग्री वाली मिश्र धातु c) Soft solder (tin-lead) / सॉफ्ट सोल्डर (टिन-लेड) d) Aluminum filler rod / एल्यूमीनियम फिलर रॉड 2. “Eddy current testing” is a non-destructive method used on chillers to inspect the:2. “एडी करंट टेस्टिंग” एक गैर-विनाशकारी विधि है जिसका उपयोग चिलरों पर निरीक्षण करने के लिए किया जाता है: a) Compressor motor windings / कंप्रेसर मोटर वाइंडिंग्स b) Condition of the condenser and evaporator tubes / कंडेनसर और इवैपोरेटर ट्यूबों की स्थिति c) Refrigerant quality / रेफ्रिजरेंट की गुणवत्ता d) Oil level / तेल का स्तर 3. To reduce noise transmission through ductwork, one should use:3. डक्टवर्क के माध्यम से शोर संचरण को कम करने के लिए, इसका उपयोग करना चाहिए: a) Thinner sheet metal / पतली शीट धातु b) More sharp bends / अधिक तेज मोड़ c) Flexible duct connectors and internal duct lining / लचीले डक्ट कनेक्टर और आंतरिक डक्ट लाइनिंग d) Higher air velocity / उच्च वायु वेग 4. Assigning a unique address to each indoor unit in a VRF system is part of the:4. एक VRF प्रणाली में प्रत्येक इनडोर इकाई को एक अनूठा पता निर्दिष्ट करना इसका हिस्सा है: a) Manufacturing process / निर्माण प्रक्रिया b) Commissioning process / कमीशनिंग प्रक्रिया c) Refrigerant charging process / रेफ्रिजरेंट चार्जिंग प्रक्रिया d) Duct installation process / डक्ट स्थापना प्रक्रिया 5. A swash plate compressor, often found in car AC, is a type of:5. एक स्वैश प्लेट कंप्रेसर, जो अक्सर कार एसी में पाया जाता है, एक प्रकार है: a) Scroll compressor / स्क्रॉल कंप्रेसर का b) Centrifugal compressor / सेंट्रीफ्यूगल कंप्रेसर का c) Variable displacement piston compressor / वेरिएबल डिस्प्लेसमेंट पिस्टन कंप्रेसर का d) Rotary vane compressor / रोटरी वेन कंप्रेसर का 6. In commercial freezers, hot gas defrost is generally more energy-efficient than:6. वाणिज्यिक फ्रीजर में, हॉट गैस डीफ्रॉस्ट आम तौर पर किससे अधिक ऊर्जा-कुशल है: a) Electric resistance defrost / इलेक्ट्रिक रेजिस्टेंस डीफ्रॉस्ट b) Off-cycle defrost / ऑफ-साइकिल डीफ्रॉस्ट c) Water defrost / वाटर डीफ्रॉस्ट d) Manual defrost / मैनुअल डीफ्रॉस्ट 7. What is the primary advantage of using software for heat load calculation?7. हीट लोड गणना के लिए सॉफ्टवेयर का उपयोग करने का प्राथमिक लाभ क्या है? a) It is always free / यह हमेशा मुफ़्त है b) It doesn’t require any technical knowledge / इसके लिए किसी तकनीकी ज्ञान की आवश्यकता नहीं है c) It provides speed, accuracy, and can model complex factors / यह गति, सटीकता प्रदान करता है, और जटिल कारकों का मॉडल बना सकता है d) It always gives a lower heat load result / यह हमेशा कम हीट लोड परिणाम देता है 8. A technician measures a contactor coil with an ohmmeter and gets a reading of “OL” (infinity). This means the coil is:8. एक तकनीशियन एक ओममीटर के साथ एक कॉन्टैक्टर कॉइल को मापता है और “OL” (अनंत) की रीडिंग प्राप्त करता है। इसका मतलब है कि कॉइल: a) Good / अच्छी है b) Shorted / शॉर्टेड है c) Open or broken / ओपन या टूटी हुई है d) Grounded / ग्राउंडेड है 9. A manometer is used during air balancing to measure:9. एयर बैलेंसिंग के दौरान एक मैनोमीटर का उपयोग मापने के लिए किया जाता है: a) Temperature and humidity / तापमान और आर्द्रता b) Static, velocity, and total pressures in ductwork / डक्टवर्क में स्थैतिक, वेग, और कुल दाब c) Electrical voltage / विद्युत वोल्टेज d) Refrigerant charge / रेफ्रिजरेंट चार्ज 10. A “triple evacuation” procedure is sometimes performed to:10. “ट्रिपल इवैक्यूएशन” प्रक्रिया कभी-कभी की जाती है: a) Charge the system three times / सिस्टम को तीन बार चार्ज करने के लिए b) Ensure maximum removal of moisture from the system / सिस्टम से नमी का अधिकतम निष्कासन सुनिश्चित करने के लिए c) Test the pressure switches three times / प्रेशर स्विच का तीन बार परीक्षण करने के लिए d) Check for leaks in three different places / तीन अलग-अलग स्थानों पर रिसाव की जांच करने के लिए 11. The primary function of a liquid line receiver is to:11. एक लिक्विड लाइन रिसीवर का प्राथमिक कार्य है: a) Filter the refrigerant / रेफ्रिजरेंट को फ़िल्टर करना b) Store excess liquid refrigerant to ensure a solid liquid supply to the TXV / TXV को एक ठोस तरल आपूर्ति सुनिश्चित करने के लिए अतिरिक्त तरल रेफ्रिजरेंट का भंडारण करना c) Separate oil from the refrigerant / रेफ्रिजरेंट से तेल अलग करना d) Increase refrigerant pressure / रेफ्रिजरेंट दाब बढ़ाना 12. The term “Ton of Refrigeration” (TR) originated from the heat required to:12. “टन ऑफ रेफ्रिजरेशन” (TR) शब्द की उत्पत्ति इस के लिए आवश्यक गर्मी से हुई है: a) Boil one ton of water in 24 hours / 24 घंटे में एक टन पानी उबालना b) Melt one ton of ice in 24 hours / 24 घंटे में एक टन बर्फ पिघलाना c) Freeze one ton of water in 1 hour / 1 घंटे में एक टन पानी जमाना d) Lift one ton of weight / एक टन वजन उठाना 13. In a car’s AC system, the evaporator is located:13. एक कार की एसी प्रणाली में, इवैपोरेटर स्थित होता है: a) In the engine bay, near the front grille / इंजन बे में, सामने की ग्रिल के पास b) Inside the passenger cabin, usually within the dashboard / यात्री केबिन के अंदर, आमतौर पर डैशबोर्ड के भीतर c) Next to the compressor / कंप्रेसर के बगल में d) In the trunk of the car / कार की डिक्की में 14. What is a primary safety concern when working on a rooftop package unit?14. रूफटॉप पैकेज यूनिट पर काम करते समय एक प्राथमिक सुरक्षा चिंता क्या है? a) Loud noise / तेज शोर b) Sunburn / धूप से जलना c) Fall hazards and electrical safety / गिरने का खतरा और विद्युत सुरक्षा d) Lack of water source / पानी के स्रोत की कमी 15. The “glide” of a zeotropic refrigerant blend means that it:15. एक ज़ियोट्रोपिक रेफ्रिजरेंट मिश्रण के “ग्लाइड” का मतलब है कि यह: a) Is very slippery / बहुत चिकना है b) Evaporates and condenses over a range of temperatures / तापमान की एक सीमा पर वाष्पीकृत और संघनित होता है c) Moves very quickly through the system / सिस्टम के माध्यम से बहुत तेजी से चलता है d) Is a single component refrigerant / एक एकल घटक रेफ्रिजरेंट है 16. What is the purpose of an oil pressure safety control on large compressors?16. बड़े कंप्रेसर पर तेल दाब सुरक्षा नियंत्रण का उद्देश्य क्या है? a) To check the oil level / तेल के स्तर की जांच करना b) To shut down the compressor if effective oil pressure is too low / यदि प्रभावी तेल दाब बहुत कम हो तो कंप्रेसर को बंद करना c) To add oil to the system automatically / सिस्टम में स्वचालित रूप से तेल जोड़ना d) To regulate the refrigerant pressure / रेफ्रिजरेंट दाब को नियंत्रित करना 17. A “direct expansion” (DX) system is one in which the evaporator is:17. एक “डायरेक्ट एक्सपेंशन” (DX) प्रणाली वह है जिसमें इवैपोरेटर: a) Located far away from the conditioned space / वातानुकूलित स्थान से बहुत दूर स्थित है b) Located directly in the air stream that is being cooled / सीधे उस वायु धारा में स्थित है जिसे ठंडा किया जा रहा है c) Cooled by water instead of air / हवा के बजाय पानी से ठंडा किया जाता है d) Always operating below freezing point / हमेशा हिमांक से नीचे काम कर रहा है 18. An electronic expansion valve (EEV) is controlled by:18. एक इलेक्ट्रॉनिक विस्तार वाल्व (EEV) नियंत्रित होता है: a) A spring and diaphragm / एक स्प्रिंग और डायाफ्राम द्वारा b) A bimetallic strip / एक बाईमेटेलिक स्ट्रिप द्वारा c) A microprocessor or electronic controller / एक माइक्रोप्रोसेसर या इलेक्ट्रॉनिक नियंत्रक द्वारा d) The pressure of the refrigerant alone / अकेले रेफ्रिजरेंट के दाब द्वारा 19. If a system is low on refrigerant, the superheat value will typically be:19. यदि एक सिस्टम में रेफ्रिजरेंट कम है, तो सुपरहीट का मान आमतौर पर होगा: a) Low / कम b) High / अधिक c) Normal / सामान्य d) Zero / शून्य 20. What is a “heat pump”?20. “हीट पंप” क्या है? a) A device that only produces heat / एक उपकरण जो केवल गर्मी पैदा करता है b) A refrigeration system that can reverse its cycle to provide both heating and cooling / एक प्रशीतन प्रणाली जो हीटिंग और कूलिंग दोनों प्रदान करने के लिए अपने चक्र को उल्टा कर सकती है c) A type of water heater / एक प्रकार का वॉटर हीटर d) A pump used in very hot environments / बहुत गर्म वातावरण में उपयोग किया जाने वाला एक पंप 21. The three basic states of matter are:21. पदार्थ की तीन मूल अवस्थाएँ हैं: a) Hot, Cold, Warm / गर्म, ठंडा, गुनगुना b) Solid, Liquid, Gas / ठोस, द्रव, गैस c) Metal, Wood, Plastic / धातु, लकड़ी, प्लास्टिक d) Acid, Base, Neutral / अम्ल, क्षार, उदासीन 22. The main function of an Air Handling Unit (AHU) is to:22. एक एयर हैंडलिंग यूनिट (AHU) का मुख्य कार्य है: a) Generate chilled water / ठंडा पानी उत्पन्न करना b) House the compressor and condenser / कंप्रेसर और कंडेनसर को रखना c) Condition and circulate air as part of an HVAC system / एक एचवीएसी प्रणाली के हिस्से के रूप में हवा को कंडीशन और प्रसारित करना d) Control the building’s lighting / भवन की प्रकाश व्यवस्था को नियंत्रित करना 23. In a multi-split AC system, what is the primary advantage?23. एक मल्टी-स्प्लिट एसी प्रणाली में, प्राथमिक लाभ क्या है? a) It is cheaper than a single split AC / यह एक सिंगल स्प्लिट एसी से सस्ता है b) One outdoor unit can serve multiple indoor units / एक आउटडोर यूनिट कई इनडोर इकाइयों को सेवा दे सकती है c) It provides better dehumidification / यह बेहतर डीह्यूमिडिफिकेशन प्रदान करता है d) It uses less refrigerant / यह कम रेफ्रिजरेंट का उपयोग करता है 24. What happens to the pressure of a gas when it is heated in a sealed container (constant volume)?24. जब एक सीलबंद कंटेनर (स्थिर आयतन) में एक गैस को गर्म किया जाता है तो उसके दाब का क्या होता है? a) It decreases / यह घटता है b) It stays the same / यह समान रहता है c) It increases / यह बढ़ता है d) It becomes zero / यह शून्य हो जाता है 25. A “direct drive” fan is different from a “belt drive” fan because it:25. एक “डायरेक्ट ड्राइव” पंखा एक “बेल्ट ड्राइव” पंखे से अलग है क्योंकि यह: a) Is less efficient / कम कुशल है b) Has its blade directly mounted on the motor shaft / इसका ब्लेड सीधे मोटर शाफ्ट पर लगा होता है c) Can move more air / अधिक हवा चला सकता है d) Is much quieter / बहुत शांत है ← Previous Next → Finish Test / टेस्ट खत्म करें