ITI MRAC 2nd Year Mock Test – 4 July 16, 2025 ITI MRAC 2nd Year Mock Test – 4 | Instant Feedback ITI MRAC 2nd Year Mock Test – 4 आईटीआई एमआरएसी द्वितीय वर्ष मॉक टेस्ट – 4 Time Left: 30:00 Test Complete! 1. A major symptom of non-condensable gases (like air) in a refrigeration system is:1. एक प्रशीतन प्रणाली में गैर-संघननशील गैसों (जैसे हवा) का एक प्रमुख लक्षण है: a) Low head pressure / निम्न हेड प्रेशर b) Low suction pressure / निम्न सक्शन प्रेशर c) Excessively high head pressure / अत्यधिक उच्च हेड प्रेशर d) No pressure reading / कोई प्रेशर रीडिंग नहीं 2. What is the purpose of chemical water treatment for cooling towers?2. कूलिंग टावरों के लिए रासायनिक जल उपचार का उद्देश्य क्या है? a) To make the water drinkable / पानी को पीने योग्य बनाना b) To prevent scale, corrosion, and biological growth / स्केल, जंग और जैविक वृद्धि को रोकना c) To cool the water faster / पानी को तेजी से ठंडा करना d) To increase the water’s boiling point / पानी का क्वथनांक बढ़ाना 3. An anemometer is an instrument used to measure:3. एक एनीमोमीटर एक उपकरण है जिसका उपयोग मापने के लिए किया जाता है: a) Air pressure / वायु दाब b) Air velocity (speed) / वायु वेग (गति) c) Air humidity / वायु आर्द्रता d) Air temperature / वायु तापमान 4. In a VRF/VRV system, the component that directs refrigerant to different indoor units for simultaneous heating and cooling is the:4. एक VRF/VRV प्रणाली में, वह घटक जो एक साथ हीटिंग और कूलिंग के लिए विभिन्न इनडोर इकाइयों को रेफ्रिजरेंट निर्देशित करता है, वह है: a) Compressor / कंप्रेसर b) Outdoor unit fan / आउटडोर यूनिट का पंखा c) Branch Selector (BS) Box / ब्रांच सेलेक्टर (BS) बॉक्स d) Thermostat / थर्मोस्टेट 5. A “freeze stat” is a safety device used on a water chiller’s evaporator to:5. “फ्रीज स्टैट” एक सुरक्षा उपकरण है जिसका उपयोग वाटर चिलर के इवैपोरेटर पर किया जाता है: a) Increase the water temperature / पानी का तापमान बढ़ाने के लिए b) Stop the compressor if the water temperature drops too low, to prevent freezing / यदि पानी का तापमान बहुत कम हो जाता है, तो जमने से रोकने के लिए कंप्रेसर को बंद करना c) Measure the refrigerant pressure / रेफ्रिजरेंट दाब को मापना d) Start the defrost cycle / डीफ्रॉस्ट चक्र शुरू करना 6. The primary difference between a car AC system using a TXV and one using an orifice tube lies in the:6. TXV का उपयोग करने वाली कार एसी प्रणाली और ऑर्फिस ट्यूब का उपयोग करने वाली प्रणाली के बीच प्राथमिक अंतर है: a) Type of compressor used / उपयोग किए गए कंप्रेसर के प्रकार में b) Type of refrigerant used / उपयोग किए गए रेफ्रिजरेंट के प्रकार में c) Use of a receiver-drier (with TXV) versus an accumulator (with orifice tube) / रिसीवर-ड्रायर (TXV के साथ) बनाम एक्यूमुलेटर (ऑर्फिस ट्यूब के साथ) के उपयोग में d) Size of the condenser / कंडेनसर के आकार में 7. An open-type commercial display case works by:7. एक ओपन-टाइप कमर्शियल डिस्प्ले केस काम करता है: a) Blowing hot air to keep customers warm / ग्राहकों को गर्म रखने के लिए गर्म हवा फेंककर b) Creating a curtain of cold air to keep the products cool / उत्पादों को ठंडा रखने के लिए ठंडी हवा का पर्दा बनाकर c) Using glass doors to seal the unit / यूनिट को सील करने के लिए कांच के दरवाजों का उपयोग करके d) Spraying a fine mist of water / पानी की महीन धुंध का छिड़काव करके 8. An electrical ladder diagram is typically read:8. एक विद्युत लैडर आरेख को आमतौर पर पढ़ा जाता है: a) From right to left, bottom to top / दाएं से बाएं, नीचे से ऊपर b) From the center outwards / केंद्र से बाहर की ओर c) From left to right, and top to bottom / बाएं से दाएं, और ऊपर से नीचे d) In any order / किसी भी क्रम में 9. An enthalpy wheel is used in HVAC systems to:9. एचवीएसी सिस्टम में एक एन्थैल्पी व्हील का उपयोग किया जाता है: a) Increase the speed of the fan / पंखे की गति बढ़ाने के लिए b) Transfer heat and moisture between supply and exhaust air streams / आपूर्ति और निकास वायु धाराओं के बीच गर्मी और नमी को स्थानांतरित करने के लिए c) Mix hot and cold water / गर्म और ठंडे पानी को मिलाने के लिए d) Generate electricity from airflow / वायु प्रवाह से बिजली उत्पन्न करने के लिए 10. An abnormally high superheat reading at the compressor usually indicates:10. कंप्रेसर पर एक असामान्य रूप से उच्च सुपरहीट रीडिंग आमतौर पर इंगित करती है: a) A refrigerant overcharge / एक रेफ्रिजरेंट ओवरचार्ज b) A starved evaporator or low refrigerant charge / एक स्टार्व्ड इवैपोरेटर या कम रेफ्रिजरेंट चार्ज c) A faulty condenser fan / एक खराब कंडेनसर पंखा d) A normal operating condition / एक सामान्य संचालन की स्थिति 11. A type of duct made from a spring steel wire helix covered by a polymer is called:11. एक पॉलीमर से ढकी स्प्रिंग स्टील वायर हेलिक्स से बना एक प्रकार का डक्ट कहलाता है: a) Rigid metal duct / कठोर धातु डक्ट b) Fiberglass duct board / फाइबरग्लास डक्ट बोर्ड c) Flexible duct / लचीला डक्ट d) Concrete duct / कंक्रीट डक्ट 12. A manometer is a tool used to measure:12. एक मैनोमीटर एक उपकरण है जिसका उपयोग मापने के लिए किया जाता है: a) Small pressure differences, like static pressure in a duct / छोटे दाब अंतर, जैसे डक्ट में स्थैतिक दाब b) High refrigerant pressures / उच्च रेफ्रिजरेंट दाब c) Electrical voltage / विद्युत वोल्टेज d) Air velocity / वायु वेग 13. The “approach” of a cooling tower is a key indicator of its:13. एक कूलिंग टॉवर का “एप्रोच” इसका एक प्रमुख संकेतक है: a) Physical size / भौतिक आकार b) Water storage capacity / जल भंडारण क्षमता c) Performance and efficiency / प्रदर्शन और दक्षता d) Noise level / शोर स्तर 14. What is the function of a flow switch in a water chiller system?14. एक वाटर चिलर प्रणाली में फ्लो स्विच का क्या कार्य है? a) To measure the water temperature / पानी का तापमान मापना b) To ensure adequate water flow before allowing the compressor to run / कंप्रेसर को चलने की अनुमति देने से पहले पर्याप्त जल प्रवाह सुनिश्चित करना c) To control the speed of the water pump / पानी के पंप की गति को नियंत्रित करना d) To add chemicals to the water / पानी में रसायन मिलाना 15. The defrost cycle in a commercial freezer can be initiated by:15. एक वाणिज्यिक फ्रीजर में डीफ्रॉस्ट चक्र शुरू किया जा सकता है: a) Opening the door / दरवाजा खोलने से b) A time clock or a temperature/pressure sensor / एक टाइम क्लॉक या एक तापमान/दाब सेंसर द्वारा c) Turning the main power off and on / मुख्य बिजली को बंद और चालू करने से d) Adding more refrigerant / अधिक रेफ्रिजरेंट जोड़ने से 16. The purpose of a “trap” in a condensate drain line is to:16. एक संघनन निकास लाइन में “ट्रैप” का उद्देश्य है: a) Filter the water / पानी को फ़िल्टर करना b) Prevent air from being drawn into or blown out of the unit / यूनिट में हवा को खींचे जाने या बाहर फेंके जाने से रोकना c) Measure the amount of water drained / निकाले गए पानी की मात्रा मापना d) Cool the water before it drains / पानी को निकलने से पहले ठंडा करना 17. If a three-phase scroll compressor is found to be running backwards, the correct action is to:17. यदि एक तीन-चरण स्क्रॉल कंप्रेसर उल्टा चलता हुआ पाया जाता है, तो सही कार्रवाई है: a) Let it run, it will correct itself / इसे चलने दें, यह खुद को ठीक कर लेगा b) Replace the compressor / कंप्रेसर को बदल दें c) Shut off the power and swap any two of the three power leads / बिजली बंद करें और तीन पावर लीड में से किन्हीं दो को आपस में बदल दें d) Add more oil to the compressor / कंप्रेसर में और तेल डालें 18. Subcooling is measured as the temperature difference between:18. सबकूलिंग को किसके बीच तापमान के अंतर के रूप में मापा जाता है: a) The evaporator inlet and outlet / इवैपोरेटर इनलेट और आउटलेट b) The refrigerant’s saturation temperature and the actual liquid line temperature at the condenser outlet / रेफ्रिजरेंट का संतृप्ति तापमान और कंडेनसर आउटलेट पर वास्तविक लिक्विड लाइन तापमान c) The air entering and leaving the condenser / कंडेनसर में प्रवेश करने और निकलने वाली हवा d) The compressor shell and the ambient air / कंप्रेसर शेल और परिवेशी हवा 19. A “direct drive” fan is one where the fan blade is:19. एक “डायरेक्ट ड्राइव” पंखा वह है जहां पंखे का ब्लेड: a) Driven by a belt and pulley / एक बेल्ट और पुली द्वारा चलाया जाता है b) Mounted directly on the motor’s shaft / सीधे मोटर के शाफ्ट पर लगाया जाता है c) Driven by a gearbox / एक गियरबॉक्स द्वारा चलाया जाता है d) Free-spinning with no motor / बिना मोटर के स्वतंत्र रूप से घूमता है 20. A restriction (partial block) in the liquid line would likely cause:20. लिक्विड लाइन में एक प्रतिबंध (आंशिक ब्लॉक) की संभावना इसका कारण बनेगी: a) High suction and high discharge pressure / उच्च सक्शन और उच्च डिस्चार्ज दाब b) Normal pressures but no cooling / सामान्य दाब लेकिन कोई कूलिंग नहीं c) A frosted or sweating spot at the restriction and low suction pressure / प्रतिबंध पर एक पाले सेओढ़ लिया या पसीने वाला स्थान और निम्न सक्शन दाब d) The compressor to shut off immediately / कंप्रेसर का तुरंत बंद हो जाना 21. The main purpose of a gas ballast valve on a vacuum pump is to:21. एक वैक्यूम पंप पर गैस बैलास्ट वाल्व का मुख्य उद्देश्य है: a) Release pressure from the pump / पंप से दाब छोड़ना b) Help prevent water vapor from condensing in the pump oil / पानी के वाष्प को पंप के तेल में संघनित होने से रोकने में मदद करना c) Measure the level of vacuum / वैक्यूम के स्तर को मापना d) Add oil to the pump while it is running / चलते समय पंप में तेल डालना 22. A hermetic compressor is one that:22. एक हर्मेटिक कंप्रेसर वह है जो: a) Can be opened and repaired on-site / ऑन-साइट खोला और मरम्मत किया जा सकता है b) Is fully sealed in a welded casing and is not serviceable / एक वेल्डेड केसिंग में पूरी तरह से सील है और सेवा योग्य नहीं है c) Is driven by an external motor with a belt / एक बाहरी मोटर द्वारा एक बेल्ट के साथ चलाया जाता है d) Uses screws instead of pistons / पिस्टन के बजाय स्क्रू का उपयोग करता है 23. The electrical symbol consisting of two parallel lines represents a:23. दो समानांतर रेखाओं से युक्त विद्युत प्रतीक प्रतिनिधित्व करता है: a) Resistor / प्रतिरोधी का b) Fuse / फ्यूज का c) Normally Open (N.O.) contact / सामान्य रूप से खुले (N.O.) संपर्क का d) Ground connection / ग्राउंड कनेक्शन का 24. In the context of cooling towers, “bleed-off” or “blowdown” is the process of:24. कूलिंग टावरों के संदर्भ में, “ब्लीड-ऑफ” या “ब्लोडाउन” प्रक्रिया है: a) Adding fresh water to the system / सिस्टम में ताजा पानी जोड़ना b) Draining a small amount of water to remove dissolved minerals / घुले हुए खनिजों को हटाने के लिए थोड़ी मात्रा में पानी निकालना c) Turning off the fan / पंखे को बंद करना d) Cleaning the tower structure / टॉवर संरचना की सफाई करना 25. A semi-hermetic compressor is different from a hermetic compressor because it:25. एक सेमी-हर्मेटिक कंप्रेसर एक हर्मेटिक कंप्रेसर से अलग है क्योंकि यह: a) Is smaller in size / आकार में छोटा है b) Can be unbolted and serviced in the field / इसे खोलकर फील्ड में सर्विस किया जा सकता है c) Does not use oil / तेल का उपयोग नहीं करता है d) Is quieter in operation / संचालन में शांत है ← Previous Next → Finish Test / टेस्ट खत्म करें