ITI Carpenter 1st Year Mock Test – 1 July 19, 2025 ITI Carpenter 1st Year Mock Test – 1 | Instant Feedback ITI Carpenter 1st Year Mock Test – 1 आईटीआई कारपेंटर प्रथम वर्ष मॉक टेस्ट – 1 Time Left: 30:00 Test Complete! 1. Which tool is used to check the squareness of a corner?1. किसी कोने की समकोणता (squareness) की जांच के लिए किस उपकरण का उपयोग किया जाता है? a) Steel Rule / स्टील रूल b) Try Square / ट्राई स्क्वायर c) Marking Gauge / मार्किंग गेज d) Bevel / बेवल 2. The process of cutting wood along the grains is called:2. लकड़ी के रेशों (grains) के साथ-साथ काटने की प्रक्रिया कहलाती है: a) Cross-cutting / क्रॉस-कटिंग b) Ripping / रिपिंग c) Planing / प्लेनिंग d) Chiseling / चिज़लिंग 3. Which of the following is a hardwood?3. निम्नलिखित में से कौन सी एक कठोर लकड़ी (hardwood) है? a) Pine / पाइन (चीड़) b) Teak / टीक (सागौन) c) Deodar / देवदार d) Spruce / स्प्रूस 4. The joint formed by joining two pieces of wood at a 90-degree angle with interlocking pins and tails is a:4. इंटरलॉकिंग पिन और टेल के साथ 90-डिग्री के कोण पर लकड़ी के दो टुकड़ों को जोड़ने से बनने वाला जोड़ है: a) Mortise and Tenon Joint / मोर्टिज़ एंड टेनन जॉइंट b) Lap Joint / लैप जॉइंट c) Dovetail Joint / डोवटेल जॉइंट d) Butt Joint / बट जॉइंट 5. What is the most important safety precaution when using a hand saw?5. हाथ की आरी का उपयोग करते समय सबसे महत्वपूर्ण सुरक्षा सावधानी क्या है? a) Saw as fast as possible / जितनी जल्दी हो सके काटना b) Keep fingers away from the cutting line / उंगलियों को कटिंग लाइन से दूर रखना c) Use a blunt saw / एक कुंद आरी का उपयोग करना d) Blow away the sawdust with your mouth / अपने मुंह से लकड़ी का बुरादा उड़ाना 6. The tool used to smoothen the surface of wood is a:6. लकड़ी की सतह को चिकना करने के लिए उपयोग किया जाने वाला उपकरण है: a) Saw / आरी b) Chisel / छेनी c) Plane / रंदा d) Hammer / हथौड़ा 7. A ‘Mortise’ is a:7. एक ‘मोर्टिज़’ है: a) A projecting part of wood / लकड़ी का एक उभरा हुआ हिस्सा b) A hole or slot cut into a piece of wood / लकड़ी के एक टुकड़े में काटा गया एक छेद या स्लॉट c) A type of screw / एक प्रकार का स्क्रू d) A type of wood / एक प्रकार की लकड़ी 8. The process of removing moisture from timber is called:8. लकड़ी से नमी हटाने की प्रक्रिया कहलाती है: a) Seasoning / सीजनिंग b) Painting / पेंटिंग c) Polishing / पॉलिशिंग d) Cutting / कटिंग 9. A ‘Claw Hammer’ is used for:9. एक ‘क्लॉ हैमर’ का उपयोग किया जाता है: a) Only hitting nails / केवल कीलें ठोंकने के लिए b) Only pulling out nails / केवल कीलें निकालने के लिए c) Both hitting and pulling out nails / कीलें ठोंकने और निकालने दोनों के लिए d) Cutting wood / लकड़ी काटने के लिए 10. What does the term ‘5S’ stand for in a workshop?10. एक वर्कशॉप में ‘5S’ शब्द का क्या अर्थ है? a) Five types of saws / पाँच प्रकार की आरियाँ b) A workplace organization method / एक कार्यस्थल संगठन विधि c) Five different wood types / पाँच अलग-अलग लकड़ी के प्रकार d) Five safety steps / पाँच सुरक्षा चरण 11. A ‘Tenon Saw’ is used for:11. एक ‘टेनन सॉ’ का उपयोग किया जाता है: a) Cutting large logs / बड़े लट्ठों को काटने के लिए b) Making fine, straight cuts for joinery / जॉइनरी के लिए महीन, सीधे कट बनाने के लिए c) Cutting curves / वक्र काटने के लिए d) Ripping long boards / लंबे बोर्डों को रिप करने के लिए 12. The annual rings in a tree help to determine its:12. एक पेड़ में वार्षिक वलय उसकी _______ को निर्धारित करने में मदद करते हैं। a) Height / ऊंचाई b) Age / आयु c) Strength / मजबूती d) Color / रंग 13. The tool used for making a hole for a screw is a:13. एक स्क्रू के लिए छेद बनाने के लिए उपयोग किया जाने वाला उपकरण है: a) Hammer / हथौड़ा b) Chisel / छेनी c) Drill / ड्रिल d) Saw / आरी 14. What is the most important safety equipment to wear when working with woodworking machinery?14. वुडवर्किंग मशीनरी के साथ काम करते समय पहनने के लिए सबसे महत्वपूर्ण सुरक्षा उपकरण क्या है? a) A tie / एक टाई b) Loose clothing / ढीले कपड़े c) Safety glasses and ear protection / सुरक्षा चश्मा और कान की सुरक्षा d) A watch / एक घड़ी 15. The joint formed by cutting a recess in one piece to receive another is a:15. दूसरे को प्राप्त करने के लिए एक टुकड़े में एक अवकाश काटकर बनाया गया जोड़ है: a) Butt Joint / बट जॉइंट b) Lap Joint / लैप जॉइंट c) Dowel Joint / डॉवेल जॉइंट d) Miter Joint / माइटर जॉइंट 16. The tool used for marking a line parallel to an edge is a:16. एक किनारे के समानांतर एक रेखा को चिह्नित करने के लिए उपयोग किया जाने वाला उपकरण है: a) Try square / ट्राई स्क्वायर b) Marking gauge / मार्किंग गेज c) Steel rule / स्टील रूल d) Bevel / बेवल 17. Which of these is a softwood?17. इनमें से कौन सी एक नरम लकड़ी (softwood) है? a) Teak / टीक (सागौन) b) Oak / ओक c) Pine / पाइन (चीड़) d) Mahogany / महोगनी 18. The process of applying a clear, protective finish to wood is:18. लकड़ी पर एक स्पष्ट, सुरक्षात्मक फिनिश लगाने की प्रक्रिया है: a) Painting / पेंटिंग b) Varnishing or Lacquering / वार्निशिंग या लैकरिंग c) Staining / स्टेनिंग d) Bleaching / ब्लीचिंग 19. A ‘tenon’ is the _______ part of a mortise and tenon joint.19. एक ‘टेनन’ एक मोर्टिज़ और टेनन जोड़ का _______ हिस्सा है। a) Hole / छेद b) Projecting part / उभरा हुआ हिस्सा c) Glue / गोंद d) Pin / पिन 20. What is the most important rule for handling tools?20. औजारों को संभालने का सबसे महत्वपूर्ण नियम क्या है? a) Keep them sharp and clean / उन्हें तेज और साफ रखना b) Use the right tool for the job / काम के लिए सही उपकरण का उपयोग करना c) Store them properly after use / उपयोग के बाद उन्हें ठीक से स्टोर करना d) All of the above / उपरोक्त सभी 21. The tool used for cutting curves in wood is a:21. लकड़ी में वक्र काटने के लिए उपयोग किया जाने वाला उपकरण है: a) Tenon saw / टेनन सॉ b) Rip saw / रिप सॉ c) Coping saw or Jigsaw / कोपिंग सॉ या जिगसॉ d) Crosscut saw / क्रॉसकट सॉ 22. Which of these is a wood defect?22. इनमें से कौन सा एक लकड़ी का दोष है? a) Knot / गाँठ b) Warp / ताना c) Crack / दरार d) All of the above / उपरोक्त सभी 23. The tool used to drive a chisel is a:23. एक छेनी को चलाने के लिए उपयोग किया जाने वाला उपकरण है: a) Mallet / मैलेट b) Screwdriver / स्क्रूड्राइवर c) Wrench / रिंच d) Pliers / प्लायर्स 24. What should you do before starting a power tool?24. एक पावर टूल शुरू करने से पहले आपको क्या करना चाहिए? a) Check that all safety guards are in place / जांचें कि सभी सुरक्षा गार्ड अपनी जगह पर हैं b) Ensure the workpiece is securely clamped / सुनिश्चित करें कि वर्कपीस सुरक्षित रूप से क्लैंप किया गया है c) Wear appropriate PPE / उपयुक्त पीपीई पहनें d) All of the above / उपरोक्त सभी 25. A miter joint is typically cut at an angle of:25. एक माइटर जोड़ को आमतौर पर किस कोण पर काटा जाता है: a) 90 degrees / 90 डिग्री b) 60 degrees / 60 डिग्री c) 45 degrees / 45 डिग्री d) 30 degrees / 30 डिग्री ← Previous Next → Finish Test / टेस्ट खत्म करें