ITI Welder 1st Year Mock Test – 10 July 19, 2025 ITI Welder 1st Year Mock Test – 10 | Instant Feedback ITI Welder 1st Year Mock Test – 10 आईटीआई वेल्डर प्रथम वर्ष मॉक टेस्ट – 10 Time Left: 30:00 Test Complete! 1. What is the primary function of the flux coating on a shielded metal arc welding (SMAW) electrode?1. शील्डेड मेटल आर्क वेल्डिंग (SMAW) इलेक्ट्रोड पर फ्लक्स कोटिंग का प्राथमिक कार्य क्या है? a) To add color to the weld / वेल्ड में रंग जोड़ना b) To create a shielding gas and form a protective slag / एक परिरक्षण गैस बनाना और एक सुरक्षात्मक स्लैग बनाना c) To cool the electrode / इलेक्ट्रोड को ठंडा करना d) To increase the electrical resistance / विद्युत प्रतिरोध बढ़ाना 2. The gas cylinder for acetylene is typically painted:2. एसिटिलीन के लिए गैस सिलेंडर को आमतौर पर पेंट किया जाता है: a) Black / काला b) Maroon / मैरून c) Blue / नीला d) Green / हरा 3. A ‘butt joint’ is used to join two plates placed:3. एक ‘बट जॉइंट’ का उपयोग दो प्लेटों को जोड़ने के लिए किया जाता है जो रखी गई हैं: a) Overlapping each other / एक दूसरे को ओवरलैप करते हुए b) Edge to edge in the same plane / एक ही तल में किनारे से किनारा मिलाकर c) At a 90-degree angle / 90-डिग्री के कोण पर d) At a 45-degree angle / 45-डिग्री के कोण पर 4. In gas welding, a ‘backfire’ is when the flame:4. गैस वेल्डिंग में, एक ‘बैकफायर’ तब होता है जब ज्वाला: a) Goes out completely / पूरी तरह से बुझ जाती है b) Burns back into the torch tip with a loud pop / एक तेज पॉप के साथ टॉर्च टिप में वापस जलती है c) Becomes very large / बहुत बड़ी हो जाती है d) Burns inside the hose / नली के अंदर जलती है 5. What is the most important PPE for a welder?5. एक वेल्डर के लिए सबसे महत्वपूर्ण पीपीई क्या है? a) Safety shoes / सुरक्षा जूते b) Leather gloves / चमड़े के दस्ताने c) Welding helmet / वेल्डिंग हेलमेट d) All of the above are essential / उपरोक्त सभी आवश्यक हैं 6. The process of preparing the edges of thick plates for welding is called:6. वेल्डिंग के लिए मोटी प्लेटों के किनारों को तैयार करने की प्रक्रिया कहलाती है: a) Edge preparation (e.g., V-groove) / एज प्रिपरेशन (जैसे, वी-ग्रूव) b) Cleaning / सफाई c) Tacking / टैकिंग d) Finishing / फिनिशिंग 7. A ‘carburizing flame’ is used for welding:7. एक ‘कार्बराइजिंग फ्लेम’ का उपयोग वेल्डिंग के लिए किया जाता है: a) Steel and cast iron / स्टील और कच्चा लोहा b) Hard-facing and for welding high-carbon steel / हार्ड-फेसिंग और उच्च-कार्बन स्टील की वेल्डिंग के लिए c) Copper and brass / तांबा और पीतल d) Aluminum / एल्यूमीनियम 8. The tool used to mark a straight line on metal is a:8. धातु पर एक सीधी रेखा को चिह्नित करने के लिए उपयोग किया जाने वाला उपकरण है: a) Hammer / हथौड़ा b) Tongs / चिमटा c) Scriber and straight edge / स्क्राइबर और स्ट्रेट एज d) File / फाइल 9. A ‘Tee Joint’ is formed when two plates meet:9. एक ‘टी जॉइंट’ तब बनता है जब दो प्लेटें मिलती हैं: a) Edge to edge / किनारे से किनारा b) With one plate overlapping the other / एक प्लेट दूसरे को ओवरलैप करती है c) At a 90-degree angle, forming a ‘T’ shape / 90-डिग्री के कोण पर, एक ‘T’ आकार बनाते हुए d) At a corner / एक कोने पर 10. What is the first aid for a flash burn to the eyes?10. आँखों में फ्लैश बर्न के लिए प्राथमिक उपचार क्या है? a) Rub the eyes / आँखों को रगड़ना b) Apply a cool, wet compress and seek medical help / एक ठंडा, गीला सेक लागू करना और चिकित्सा सहायता लेना c) Put hot water in the eyes / आँखों में गर्म पानी डालना d) Look at a bright light / एक तेज रोशनी को देखना 11. A ‘fillet weld’ has a cross-section that is approximately:11. एक ‘फिलेट वेल्ड’ का एक क्रॉस-सेक्शन होता है जो लगभग होता है: a) Square / वर्गाकार b) Triangular / त्रिकोणीय c) Circular / वृत्ताकार d) Rectangular / आयताकार 12. The color of an oxygen cylinder is:12. एक ऑक्सीजन सिलेंडर का रंग होता है: a) Red / लाल b) Black / काला c) Maroon / मैरून d) Blue / नीला 13. The main purpose of an earth clamp in arc welding is to:13. आर्क वेल्डिंग में एक अर्थ क्लैंप का मुख्य उद्देश्य है: a) Hold the electrode / इलेक्ट्रोड को पकड़ना b) Complete the electrical circuit / विद्युत सर्किट को पूरा करना c) Clean the weld / वेल्ड को साफ करना d) Adjust the current / करंट को समायोजित करना 14. A ‘V’ groove preparation is done for a:14. एक ‘V’ खांचे की तैयारी किसके लिए की जाती है: a) Lap joint / लैप जॉइंट b) Tee joint / टी जॉइंट c) Butt joint / बट जॉइंट d) Corner joint / कॉर्नर जॉइंट 15. What is the most important safety rule in a welding shop?15. एक वेल्डिंग शॉप में सबसे महत्वपूर्ण सुरक्षा नियम क्या है? a) Wear appropriate PPE and ensure good ventilation / उपयुक्त पीपीई पहनना और अच्छा वेंटिलेशन सुनिश्चित करना b) Weld as quickly as possible / जितनी जल्दी हो सके वेल्ड करना c) Use the highest current setting / उच्चतम करंट सेटिंग का उपयोग करना d) Work near flammable materials / ज्वलनशील पदार्थों के पास काम करना 16. The process of joining two pieces of metal by heating them and using a filler metal with a lower melting point is:16. धातु के दो टुकड़ों को गर्म करके और कम गलनांक वाली एक भराव धातु का उपयोग करके जोड़ने की प्रक्रिया है: a) Welding / वेल्डिंग b) Brazing or Soldering / ब्रेज़िंग या सोल्डरिंग c) Forging / फोर्जिंग d) Riveting / रिवेटिंग 17. A ‘Tee Joint’ is formed when two plates are joined at:17. एक ‘टी जॉइंट’ तब बनता है जब दो प्लेटों को जोड़ा जाता है: a) 180 degrees / 180 डिग्री पर b) 90 degrees to each other in a ‘T’ shape / एक ‘T’ आकार में एक दूसरे से 90 डिग्री पर c) In the same plane / एक ही तल में d) Overlapping each other / एक दूसरे को ओवरलैप करते हुए 18. The tool used for making straight line marks on metal is a:18. धातु पर सीधी रेखा के निशान बनाने के लिए उपयोग किया जाने वाला उपकरण है: a) Scriber and straight edge / स्क्राइबर और स्ट्रेट एज b) Center punch / सेंटर पंच c) Divider / डिवाइडर d) Hammer / हथौड़ा 19. A ‘carburizing flame’ has an excess of:19. एक ‘कार्बराइजिंग फ्लेम’ में अधिकता होती है: a) Oxygen / ऑक्सीजन की b) Acetylene / एसिटिलीन की c) Nitrogen / नाइट्रोजन की d) Argon / आर्गन की 20. Which of these is a temporary fastener?20. इनमें से कौन एक अस्थायी फास्टनर है? a) Rivet / रिवेट b) Weld / वेल्ड c) Nut and Bolt / नट और बोल्ट d) Brazed joint / ब्रेज़्ड जोड़ 21. The most important quality of a good welder is:21. एक अच्छे वेल्डर का सबसे महत्वपूर्ण गुण है: a) Speed / गति b) Skill, a steady hand, and knowledge of safety / कौशल, एक स्थिर हाथ, और सुरक्षा का ज्ञान c) Strength / शक्ति d) Using the newest machine / नवीनतम मशीन का उपयोग करना 22. An ‘oxidizing flame’ has an excess of:22. एक ‘ऑक्सीडाइजिंग फ्लेम’ में अधिकता होती है: a) Oxygen / ऑक्सीजन की b) Acetylene / एसिटिलीन की c) Hydrogen / हाइड्रोजन की d) Nitrogen / नाइट्रोजन की 23. The tool used to clean a weld after chipping is a:23. चिपिंग के बाद एक वेल्ड को साफ करने के लिए उपयोग किया जाने वाला उपकरण है: a) Hammer / हथौड़ा b) File / फाइल c) Wire brush / वायर ब्रश d) Scraper / स्क्रैपर 24. What is the main safety risk from an electric arc?24. एक इलेक्ट्रिक आर्क से मुख्य सुरक्षा जोखिम क्या है? a) Loud noise / तेज शोर b) Intense ultraviolet (UV) radiation and sparks / तीव्र पराबैंगनी (UV) विकिरण और चिंगारी c) Bad smell / बुरी गंध d) Low temperature / कम तापमान 25. A fillet weld is roughly _______ in cross-section.25. एक फिलेट वेल्ड क्रॉस-सेक्शन में लगभग _______ होता है। a) Square / वर्गाकार b) Circular / वृत्ताकार c) Triangular / त्रिकोणीय d) Rectangular / आयताकार ← Previous Next → Finish Test / टेस्ट खत्म करें