ITI Instrument Mechanic 1st Year Mock Test – 3 July 18, 2025 ITI Instrument Mechanic 1st Year Mock Test – 3 | Instant Feedback ITI Instrument Mechanic 1st Year Mock Test – 3 आईटीआई इंस्ट्रूमेंट मैकेनिक प्रथम वर्ष मॉक टेस्ट – 3 Time Left: 30:00 Test Complete! 1. What is the most important safety rule when working with electricity?1. बिजली के साथ काम करते समय सबसे महत्वपूर्ण सुरक्षा नियम क्या है? a) Work with wet hands / गीले हाथों से काम करना b) Use tools with broken insulation / टूटे हुए इन्सुलेशन वाले उपकरणों का उपयोग करना c) Always assume a circuit is live and use a tester / हमेशा मान लें कि एक सर्किट लाइव है और एक टेस्टर का उपयोग करें d) Bypass safety fuses / सुरक्षा फ्यूज को बायपास करना 2. The least count of a standard metric micrometer is:2. एक मानक मीट्रिक माइक्रोमीटर का अल्पतमांक है: a) 0.1 mm b) 0.02 mm c) 0.05 mm d) 0.01 mm 3. The unit of electrical current is:3. विद्युत धारा की इकाई है: a) Volt (V) / वोल्ट (V) b) Ampere (A) / एम्पीयर (A) c) Ohm (Ω) / ओम (Ω) d) Watt (W) / वाट (W) 4. Which file is used for finishing sharp corners?4. तेज कोनों को फिनिश करने के लिए किस फाइल का उपयोग किया जाता है? a) Flat file / फ्लैट फाइल b) Round file / राउंड फाइल c) Square file or Triangular file / स्क्वायर फाइल या त्रिकोणीय फाइल d) Half-round file / हाफ-राउंड फाइल 5. A logic gate that produces a HIGH output only when all its inputs are HIGH is a(n):5. एक लॉजिक गेट जो केवल तभी HIGH आउटपुट देता है जब उसके सभी इनपुट HIGH हों, वह है: a) OR gate / OR गेट b) NOT gate / NOT गेट c) AND gate / AND गेट d) NAND gate / NAND गेट 6. The process of making a hole with a drill is called:6. एक ड्रिल के साथ एक छेद बनाने की प्रक्रिया कहलाती है: a) Tapping / टैपिंग b) Boring / बोरिंग c) Drilling / ड्रिलिंग d) Reaming / रीमिंग 7. A diode is a component that:7. एक डायोड एक घटक है जो: a) Amplifies current / करंट को बढ़ाता है b) Stores charge / आवेश का भंडारण करता है c) Allows current to flow in one direction only / करंट को केवल एक दिशा में प्रवाहित होने देता है d) Resists the flow of current / करंट के प्रवाह का विरोध करता है 8. The tool used for marking a point before drilling is a:8. ड्रिलिंग से पहले एक बिंदु को चिह्नित करने के लिए उपयोग किया जाने वाला उपकरण है: a) Scriber / स्क्राइबर b) Divider / डिवाइडर c) Center Punch / सेंटर पंच d) File / फाइल 9. An LVDT (Linear Variable Differential Transformer) is used to measure:9. एक LVDT (रैखिक चर विभेदक ट्रांसफार्मर) का उपयोग मापने के लिए किया जाता है: a) Temperature / तापमान b) Pressure / दबाव c) Flow / प्रवाह d) Displacement / विस्थापन 10. In a parallel circuit, the total resistance is:10. एक समानांतर सर्किट में, कुल प्रतिरोध है: a) The sum of all resistances / सभी प्रतिरोधों का योग b) Always less than the smallest resistance in the circuit / सर्किट में सबसे छोटे प्रतिरोध से हमेशा कम c) The average of all resistances / सभी प्रतिरोधों का औसत d) The same as the largest resistance / सबसे बड़े प्रतिरोध के समान 11. A ‘try square’ is used for:11. एक ‘ट्राई स्क्वायर’ का उपयोग किया जाता है: a) Drawing circles / वृत्त बनाने के लिए b) Measuring angles / कोण मापने के लिए c) Checking squareness (90°) and marking lines / चौकोरपन (90°) की जांच करने और रेखाएं चिह्नित करने के लिए d) Measuring length / लंबाई मापने के लिए 12. The tool used for cutting external threads on a rod is a:12. एक रॉड पर बाहरी चूड़ियाँ काटने के लिए उपयोग किया जाने वाला उपकरण है: a) Tap / टैप b) Die / डाई c) Reamer / रीमर d) Drill / ड्रिल 13. The unit of electrical power is:13. विद्युत शक्ति की इकाई है: a) Ampere (A) / एम्पीयर (A) b) Volt (V) / वोल्ट (V) c) Ohm (Ω) / ओम (Ω) d) Watt (W) / वाट (W) 14. What is the most important safety precaution before starting work on any machine?14. किसी भी मशीन पर काम शुरू करने से पहले सबसे महत्वपूर्ण सुरक्षा सावधानी क्या है? a) Ensure it is clean / सुनिश्चित करें कि यह साफ है b) Ensure all safety guards are in place and working properly / सुनिश्चित करें कि सभी सुरक्षा गार्ड अपनी जगह पर हैं और ठीक से काम कर रहे हैं c) Check its color / इसका रंग जांचें d) Talk to your colleague / अपने सहकर्मी से बात करें 15. An OR gate produces a HIGH output if:15. एक OR गेट HIGH आउटपुट देता है यदि: a) All its inputs are LOW / इसके सभी इनपुट LOW हैं b) At least one of its inputs is HIGH / इसका कम से कम एक इनपुट HIGH है c) The inputs are opposite / इनपुट विपरीत हैं d) All its inputs are HIGH / इसके सभी इनपुट HIGH हैं 16. The instrument used to measure very small gaps or clearances is:16. बहुत छोटे गैप या क्लीयरेंस को मापने के लिए उपयोग किया जाने वाला उपकरण है: a) Steel rule / स्टील रूल b) Vernier caliper / वर्नियर कैलिपर c) Feeler gauge / फिलर गेज d) Micrometer / माइक्रोमीटर 17. A transistor is a semiconductor device with _______ terminals.17. एक ट्रांजिस्टर _______ टर्मिनलों वाला एक अर्धचालक उपकरण है। a) One / एक b) Two / दो c) Three / तीन d) Four / चार 18. The tool used for marking an arc or circle is a:18. एक चाप या वृत्त को चिह्नित करने के लिए उपयोग किया जाने वाला उपकरण है: a) Scriber / स्क्राइबर b) Divider or Compass / डिवाइडर या कम्पास c) Punch / पंच d) Straight edge / स्ट्रेट एज 19. A rotameter is an instrument used to measure:19. एक रोटामीटर एक उपकरण है जिसका उपयोग मापने के लिए किया जाता है: a) Fluid flow rate / द्रव प्रवाह दर b) Temperature / तापमान c) Pressure / दबाव d) Viscosity / श्यानता 20. What is a key safety measure when working with soldering iron?20. सोल्डरिंग आयरन के साथ काम करते समय एक प्रमुख सुरक्षा उपाय क्या है? a) Touch the tip to check if it’s hot / यह जांचने के लिए टिप को छूना कि क्या यह गर्म है b) Use a proper stand and ensure good ventilation / एक उचित स्टैंड का उपयोग करना और अच्छा वेंटिलेशन सुनिश्चित करना c) Leave it on the workbench directly / इसे सीधे वर्कबेंच पर छोड़ देना d) Clean the tip with your hand / टिप को अपने हाथ से साफ करना 21. In a parallel circuit, what remains constant across all components?21. एक समानांतर सर्किट में, सभी घटकों में क्या स्थिर रहता है? a) Current / करंट b) Resistance / प्रतिरोध c) Voltage / वोल्टेज d) Power / शक्ति 22. Which instrument is best for accurately measuring the outside diameter of a shaft?22. एक शाफ्ट के बाहरी व्यास को सटीक रूप से मापने के लिए कौन सा उपकरण सबसे अच्छा है? a) Steel rule / स्टील रूल b) Vernier caliper / वर्नियर कैलिपर c) Outside micrometer / बाहरी माइक्रोमीटर d) Inside caliper / इनसाइड कैलिपर 23. The first step in the 5S methodology is:23. 5S कार्यप्रणाली में पहला कदम है: a) Shine (Seiso) / शाइन (सीसो) b) Sort (Seiri) / सॉर्ट (सेइरी) c) Set in Order (Seiton) / सेट इन ऑर्डर (सीटोन) d) Standardize (Seiketsu) / स्टैंडर्डाइज (सेइकेत्सु) 24. What is the main purpose of a hacksaw?24. एक हैकसॉ का मुख्य उद्देश्य क्या है? a) To cut wood / लकड़ी काटने के लिए b) To cut metal / धातु काटने के लिए c) To smooth surfaces / सतहों को चिकना करने के लिए d) To drill holes / छेद ड्रिल करने के लिए 25. A NOT gate has:25. एक NOT गेट में होता है: a) One input and one output / एक इनपुट और एक आउटपुट b) Two inputs and one output / दो इनपुट और एक आउटपुट c) One input and two outputs / एक इनपुट और दो आउटपुट d) Two inputs and two outputs / दो इनपुट और दो आउटपुट ← Previous Next → Finish Test / टेस्ट खत्म करें