ITI Draughtsman Mechanical 1st Year Mock Test – 9 July 17, 2025 ITI Draughtsman Mechanical 1st Year Mock Test – 9 | Instant Feedback ITI Draughtsman Mechanical 1st Year Mock Test – 9 आईटीआई ड्राफ्ट्समैन मैकेनिकल प्रथम वर्ष मॉक टेस्ट – 9 Time Left: 30:00 Test Complete! 1. Which pencil grade is the softest and produces the darkest line?1. कौन सा पेंसिल ग्रेड सबसे नरम है और सबसे गहरी रेखा बनाता है? a) 4H b) HB c) 2B d) 6B 2. In an isometric drawing, what angle do isometric lines make with the horizontal?2. एक आइसोमेट्रिक ड्राइंग में, आइसोमेट्रिक रेखाएं क्षैतिज के साथ क्या कोण बनाती हैं? a) 45° b) 60° c) 30° d) 90° 3. The distance from a point on one thread to the corresponding point on the next thread, measured parallel to the axis, is the:3. एक थ्रेड पर एक बिंदु से अगले थ्रेड पर संगत बिंदु तक की दूरी, जिसे अक्ष के समानांतर मापा जाता है, वह है: a) Pitch / पिच b) Lead / लीड c) Depth / गहराई d) Crest / क्रेस्ट 4. The first aid for a foreign particle in the eye is to:4. आंख में किसी बाहरी कण के लिए प्राथमिक उपचार है: a) Rub the eye hard / आंख को जोर से रगड़ना b) Flush the eye with clean water / आंख को साफ पानी से धोना c) Use a magnet to remove it / इसे हटाने के लिए एक चुंबक का उपयोग करना d) Put a bandage over it / इस पर एक पट्टी लगाना 5. What is the purpose of a sectional view?5. एक सेक्शनल व्यू का उद्देश्य क्या है? a) To show the object in 3D / वस्तु को 3D में दिखाना b) To show the hidden internal details of an object / किसी वस्तु के छिपे हुए आंतरिक विवरण को दिखाना c) To show only the external surfaces / केवल बाहरी सतहों को दिखाना d) To make the drawing smaller / ड्राइंग को छोटा बनाना 6. The CAD command to reverse the last operation is:6. पिछली कार्रवाई को उलटने के लिए CAD कमांड है: a) REPEAT / रिपीट b) ERASE / इरेज c) UNDO / अनडू d) CANCEL / कैंसिल 7. Which of these is a non-ferrous metal?7. इनमें से कौन सी एक अलौह धातु है? a) Mild Steel / माइल्ड स्टील b) Cast Iron / कच्चा लोहा c) Wrought Iron / रॉट आयरन d) Copper / तांबा 8. A representative fraction (R.F.) of 1:50 indicates a:8. 1:50 का एक निरूपक भिन्न (R.F.) इंगित करता है: a) Full size scale / पूर्ण आकार का पैमाना b) Reducing scale / छोटा करने वाला पैमाना c) Enlarging scale / बड़ा करने वाला पैमाना d) Not a scale / एक पैमाना नहीं 9. To draw a tangent to a circle from a point on its circumference, the tangent will be _______ to the radius at that point.9. इसकी परिधि पर एक बिंदु से एक वृत्त पर एक स्पर्शरेखा खींचने के लिए, स्पर्शरेखा उस बिंदु पर त्रिज्या के _______ होगी। a) Parallel / समानांतर b) Perpendicular / लंबवत c) At 45 degrees / 45 डिग्री पर d) At 60 degrees / 60 डिग्री पर 10. The property of a material to resist fracture under impact loading is called:10. प्रभाव भार के तहत फ्रैक्चर का विरोध करने के लिए किसी सामग्री का गुण कहलाता है: a) Hardness / कठोरता b) Brittleness / भंगुरता c) Toughness / टफनेस d) Ductility / तन्यता 11. A drawing that gives a 3D pictorial representation of an object is a(n):11. एक ड्राइंग जो किसी वस्तु का 3D चित्रात्मक प्रतिनिधित्व देती है, वह है: a) Orthographic drawing / ऑर्थोग्राफिक ड्राइंग b) Sectional drawing / सेक्शनल ड्राइंग c) Assembly drawing / असेंबली ड्राइंग d) Isometric drawing / आइसोमेट्रिक ड्राइंग 12. A half-section view is used for:12. एक हाफ-सेक्शन व्यू का उपयोग किया जाता है: a) Unsymmetrical objects / असममित वस्तुओं के लिए b) Symmetrical objects, to show internal and external details in one view / सममित वस्तुओं के लिए, एक ही दृश्य में आंतरिक और बाहरी विवरण दिखाने के लिए c) Very small objects / बहुत छोटी वस्तुओं के लिए d) Very long objects / बहुत लंबी वस्तुओं के लिए 13. The main purpose of a split pin is to:13. एक स्प्लिट पिन का मुख्य उद्देश्य है: a) Join two shafts / दो शाफ्टों को जोड़ना b) Prevent a nut from loosening due to vibration / एक नट को कंपन के कारण ढीला होने से रोकना c) Act as a bearing / एक बेयरिंग के रूप में कार्य करना d) Measure the length of a bolt / एक बोल्ट की लंबाई मापना 14. Class C fires involve:14. क्लास C की आग में शामिल हैं: a) Wood and paper / लकड़ी और कागज b) Flammable liquids / ज्वलनशील तरल पदार्थ c) Energized electrical equipment / सक्रिय विद्युत उपकरण d) Combustible metals / ज्वलनशील धातुएं 15. In which dimensioning system is the text placed so that it can be read from the bottom or the right-hand side?15. किस विमांकन प्रणाली में टेक्स्ट इस तरह रखा जाता है कि उसे नीचे या दाईं ओर से पढ़ा जा सके? a) Unidirectional system / यूनिडायरेक्शनल सिस्टम b) Aligned system / अलाइन्ड सिस्टम c) Chain dimensioning / चेन विमांकन d) Parallel dimensioning / पैरेलल विमांकन 16. The front view of a cylinder resting on its base on H.P. is a:16. H.P. पर अपने आधार पर टिके हुए एक सिलेंडर का फ्रंट व्यू है: a) Circle / एक वृत्त b) Rectangle / एक आयत c) Square / एक वर्ग d) Triangle / एक त्रिभुज 17. Which CAD command is used to create parallel copies of lines or concentric circles?17. रेखाओं की समानांतर प्रतियां या संकेंद्रित वृत्त बनाने के लिए किस CAD कमांड का उपयोग किया जाता है? a) ARRAY / ऐरे b) COPY / कॉपी c) OFFSET / ऑफसेट d) MIRROR / मिरर 18. The tool used to cut external threads manually is a:18. मैन्युअल रूप से बाहरी चूड़ियाँ काटने के लिए उपयोग किया जाने वाला उपकरण है: a) Tap / टैप b) Drill / ड्रिल c) Die / डाई d) Reamer / रीमर 19. To bisect an angle, the instrument used is a:19. एक कोण को समद्विभाजित करने के लिए, उपयोग किया जाने वाला उपकरण है: a) Protractor / प्रोट्रैक्टर b) Set square / सेट स्क्वायर c) Compass / कम्पास d) Scale / पैमाना 20. In an assembly drawing, parts are identified by:20. एक असेंबली ड्राइंग में, भागों की पहचान की जाती है: a) Their colors / उनके रंगों से b) Their materials / उनकी सामग्रियों से c) Ballooned numbers referencing a parts list / एक पार्ट्स सूची को संदर्भित करने वाले गुब्बारे वाले नंबरों से d) Their weights / उनके वजन से 21. The symbol ‘Φ’ represents:21. ‘Φ’ प्रतीक दर्शाता है: a) Radius / त्रिज्या b) Diameter / व्यास c) Angle / कोण d) Length / लंबाई 22. What is the most important rule before using a power tool for the first time?22. पहली बार किसी पावर टूल का उपयोग करने से पहले सबसे महत्वपूर्ण नियम क्या है? a) Check its color / इसका रंग जांचें b) Read the manufacturer’s instruction manual and understand its operation / निर्माता के निर्देश मैनुअल को पढ़ें और इसके संचालन को समझें c) See if it is heavy / देखें कि क्या यह भारी है d) Use it at maximum speed / इसे अधिकतम गति पर उपयोग करें 23. In orthographic projection, views are drawn as if the observer is at:23. ऑर्थोग्राफिक प्रोजेक्शन में, व्यू इस तरह से खींचे जाते हैं जैसे कि प्रेक्षक है: a) A finite distance / एक सीमित दूरी पर b) Infinity / अनंत पर c) Very close to the object / वस्तु के बहुत करीब d) Inside the object / वस्तु के अंदर 24. What type of fastener is a rivet?24. एक रिवेट किस प्रकार का फास्टनर है? a) Temporary / अस्थायी b) Semi-permanent / अर्ध-स्थायी c) Permanent / स्थायी d) Adjustable / समायोज्य 25. What is the main purpose of a drawing sheet’s border?25. एक ड्राइंग शीट के बॉर्डर का मुख्य उद्देश्य क्या है? a) To define the working space of the drawing / ड्राइंग के कार्य स्थान को परिभाषित करना b) For decoration / सजावट के लिए c) To make the sheet stronger / शीट को मजबूत बनाने के लिए d) To write notes / नोट्स लिखने के लिए ← Previous Next → Finish Test / टेस्ट खत्म करें