ITI Draughtsman Civil 2nd Year Mock Test – 9 July 17, 2025 ITI Draughtsman Civil 2nd Year Mock Test – 9 | Instant Feedback ITI Draughtsman Civil 2nd Year Mock Test – 9 आईटीआई ड्राफ्ट्समैन सिविल द्वितीय वर्ष मॉक टेस्ट – 9 Time Left: 30:00 Test Complete! 1. In a steel truss, a gusset plate is used to:1. एक स्टील ट्रस में, एक गसेट प्लेट का उपयोग किया जाता है: a) Support the roof covering / छत के आवरण को सहारा देने के लिए b) Connect multiple members at a joint / एक जोड़ पर कई सदस्यों को जोड़ने के लिए c) Provide decoration / सजावट प्रदान करने के लिए d) Act as a main beam / एक मुख्य बीम के रूप में कार्य करने के लिए 2. The CAD command to cut parts of an object that intersect with another object is:2. किसी वस्तु के उन हिस्सों को काटने के लिए जो किसी अन्य वस्तु से प्रतिच्छेद करते हैं, CAD कमांड है: a) ERASE / इरेज b) BREAK / ब्रेक c) TRIM / ट्रिम d) EXPLODE / एक्सप्लोड 3. The minimum grade of concrete for general RCC work as per IS:456 is:3. IS:456 के अनुसार सामान्य RCC कार्य के लिए कंक्रीट का न्यूनतम ग्रेड है: a) M15 b) M20 c) M25 d) M10 4. Superelevation on roads is provided to:4. सड़कों पर सुपरएलिवेशन प्रदान किया जाता है: a) Counteract the centrifugal force on curves / वक्रों पर केन्द्रापसारक बल का प्रतिकार करने के लिए b) Drain rainwater / वर्षा जल की निकासी के लिए c) Reduce the speed of vehicles / वाहनों की गति कम करने के लिए d) Widen the road / सड़क को चौड़ा करने के लिए 5. What is the unit of measurement for plastering work?5. प्लास्टर के काम के लिए माप की इकाई क्या है? a) Cubic meter (cum) / घन मीटर (cum) b) Running meter (m) / रनिंग मीटर (m) c) Square meter (sqm) / वर्ग मीटर (sqm) d) Kilogram (kg) / किलोग्राम (kg) 6. A planimeter is used to measure _______ from a drawing.6. एक प्लानीमीटर का उपयोग एक ड्राइंग से _______ मापने के लिए किया जाता है। a) Area / क्षेत्रफल b) Length / लंबाई c) Angle / कोण d) Volume / आयतन 7. A vent pipe is provided in a drainage system to:7. एक जल निकासी प्रणाली में एक वेंट पाइप प्रदान किया जाता है: a) Carry rainwater / वर्षा जल ले जाने के लिए b) Release foul gases and maintain atmospheric pressure / दुर्गंधयुक्त गैसों को छोड़ने और वायुमंडलीय दाब बनाए रखने के लिए c) Carry waste water / अपशिष्ट जल ले जाने के लिए d) Filter the air / हवा को फ़िल्टर करने के लिए 8. The line used to show where a section cut is taken is a:8. यह दिखाने के लिए कि एक सेक्शन कट कहाँ लिया गया है, उपयोग की जाने वाली रेखा है: a) Hidden line / छिपी हुई रेखा b) Center line / केंद्र रेखा c) Cutting plane line / कटिंग प्लेन लाइन d) Dimension line / विमा रेखा 9. A cantilever beam is one that is:9. एक कैंटिलीवर बीम वह है जो: a) Supported at both ends / दोनों सिरों पर समर्थित है b) Fixed at one end and free at the other / एक सिरे पर स्थिर है और दूसरे पर मुक्त है c) Supported on more than two supports / दो से अधिक सपोर्ट पर समर्थित है d) Hanging from a support / एक सपोर्ट से लटक रही है 10. The intermediate supports of a multi-span bridge are called:10. एक मल्टी-स्पैन पुल के मध्यवर्ती समर्थन कहलाते हैं: a) Abutments / एबटमेंट्स b) Piers / पियर्स c) Decks / डेक d) Arches / मेहराब 11. A septic tank is primarily a:11. एक सेप्टिक टैंक मुख्य रूप से है: a) Water storage tank / एक जल भंडारण टैंक b) Sedimentation and digestion tank for sewage / सीवेज के लिए एक अवसादन और पाचन टैंक c) Rainwater harvesting tank / एक वर्षा जल संचयन टैंक d) Swimming pool / एक स्विमिंग पूल 12. The “Long wall – short wall” method is a type of:12. “लंबी दीवार – छोटी दीवार” विधि एक प्रकार है: a) Detailed estimate method / विस्तृत अनुमान विधि का b) Approximate estimate method / अनुमानित अनुमान विधि का c) Rate analysis method / दर विश्लेषण विधि का d) Surveying method / सर्वेक्षण विधि का 13. The main tension members in a roof truss are called:13. एक छत के ट्रस में मुख्य तनाव सदस्य कहलाते हैं: a) Rafters / राफ्टर्स b) Struts / स्ट्रट्स c) Ties / टाइज d) Purlins / पर्लिन 14. Contour lines of a ridge line show:14. एक रिज लाइन की कंटूर रेखाएं दिखाती हैं: a) Higher values inside the loop / लूप के अंदर उच्च मान b) Lower values inside the loop / लूप के अंदर निम्न मान c) Straight lines / सीधी रेखाएं d) Parallel lines / समानांतर रेखाएं 15. What does the “TRIM” command do in AutoCAD?15. ऑटोकैड में “TRIM” कमांड क्या करती है? a) It extends a line / यह एक रेखा को बढ़ाती है b) It cuts away parts of an object at a cutting edge / यह एक कटिंग एज पर एक वस्तु के हिस्सों को काटती है c) It deletes the entire object / यह पूरी वस्तु को हटा देती है d) It creates a copy of the object / यह वस्तु की एक प्रति बनाती है 16. The vertical members on the sides of a door opening are the:16. एक दरवाजे के उद्घाटन के किनारों पर ऊर्ध्वाधर सदस्य हैं: a) Posts or Jambs / पोस्ट्स या जैम्ब्स b) Lintel / लिंटेल c) Sill / सिल d) Shutter / शटर 17. A “manhole” provides access to:17. एक “मैनहोल” तक पहुंच प्रदान करता है: a) The water supply line / जल आपूर्ति लाइन b) The underground sewer line / भूमिगत सीवर लाइन c) The foundation of a building / एक इमारत की नींव d) The roof / छत 18. The main purpose of a building bye-law is to ensure:18. एक भवन उप-नियम का मुख्य उद्देश्य सुनिश्चित करना है: a) That all buildings look the same / कि सभी इमारतें एक जैसी दिखें b) Safety, health, and orderly development / सुरक्षा, स्वास्थ्य, और व्यवस्थित विकास c) The building is expensive / इमारत महंगी हो d) The construction is fast / निर्माण तेज हो 19. The bottom chord of a roof truss is usually under:19. एक छत के ट्रस का निचला कॉर्ड आमतौर पर होता है: a) Compression / संपीड़न में b) Bending / झुकने में c) Tension / तनाव में d) Shear / कतरनी में 20. What is a “culvert”?20. एक “पुलिया” क्या है? a) A large bridge over a river / एक नदी पर एक बड़ा पुल b) A structure that allows water to flow under a road or railway / एक संरचना जो पानी को एक सड़क या रेलवे के नीचे से बहने की अनुमति देती है c) A type of dam / एक प्रकार का बांध d) A water storage tank / एक जल भंडारण टैंक 21. The main difference between English bond and Flemish bond is:21. इंग्लिश बांड और फ्लेमिश बांड के बीच मुख्य अंतर है: a) English bond is stronger / इंग्लिश बांड अधिक मजबूत है b) Flemish bond has a better appearance / फ्लेमिश बांड की दिखावट बेहतर है c) Their arrangement of headers and stretchers / उनके हेडर और स्ट्रेचर की व्यवस्था d) The type of mortar used / उपयोग किए गए मोर्टार का प्रकार 22. What does the term “curing” of concrete refer to?22. कंक्रीट की “क्योरिंग” (तराई) शब्द का क्या अर्थ है? a) Mixing the concrete ingredients / कंक्रीट सामग्री को मिलाना b) Placing the concrete in formwork / फॉर्मवर्क में कंक्रीट डालना c) Keeping the concrete moist to allow it to gain strength / इसे मजबूती प्राप्त करने की अनुमति देने के लिए कंक्रीट को नम रखना d) Smoothing the surface of the concrete / कंक्रीट की सतह को चिकना करना 23. In surveying, what is a “backsight”?23. सर्वेक्षण में, एक “बैकसाइट” क्या है? a) A reading taken on a point of known elevation / ज्ञात ऊंचाई के एक बिंदु पर ली गई एक रीडिंग b) The last reading taken from an instrument setup / एक उपकरण सेटअप से ली गई अंतिम रीडिंग c) A reading taken looking backwards / पीछे की ओर देखते हुए ली गई एक रीडिंग d) Any reading taken between a backsight and a foresight / एक बैकसाइट और एक फोरसाइट के बीच ली गई कोई भी रीडिंग 24. The foundation for a single wall is typically a:24. एक एकल दीवार के लिए नींव आमतौर पर होती है: a) Raft foundation / राफ्ट नींव b) Strip foundation / स्ट्रिप नींव c) Pile foundation / पाइल नींव d) Isolated footing / आइसोलेटेड फुटिंग 25. What is the primary role of a draughtsman in a civil engineering project?25. एक सिविल इंजीनियरिंग परियोजना में एक ड्राफ्ट्समैन की प्राथमिक भूमिका क्या है? a) To supervise the construction work / निर्माण कार्य का पर्यवेक्षण करना b) To prepare detailed drawings and plans based on the engineer’s design / इंजीनियर के डिजाइन के आधार पर विस्तृत चित्र और योजनाएं तैयार करना c) To calculate the cost of the project / परियोजना की लागत की गणना करना d) To conduct the land survey / भूमि सर्वेक्षण करना ← Previous Next → Finish Test / टेस्ट खत्म करें