ITI MRAC 2nd Year Mock Test – 2 July 16, 2025 ITI MRAC 2nd Year Mock Test – 2 | Instant Feedback ITI MRAC 2nd Year Mock Test – 2 आईटीआई एमआरएसी द्वितीय वर्ष मॉक टेस्ट – 2 Time Left: 30:00 Test Complete! 1. What is a “Package Air Conditioner”?1. “पैकेज एयर कंडीशनर” क्या है? a) An AC that comes in a small box / एक एसी जो एक छोटे से बॉक्स में आता है b) An AC unit where all major components are housed in a single casing / एक एसी इकाई जहाँ सभी प्रमुख घटक एक ही आवरण में रखे जाते हैं c) A portable air conditioner / एक पोर्टेबल एयर कंडीशनर d) An AC system with separate indoor and outdoor units / अलग-अलग इनडोर और आउटडोर इकाइयों वाली एक एसी प्रणाली 2. In an ice plant, what is the secondary refrigerant used to freeze water?2. एक बर्फ के कारखाने में, पानी को जमाने के लिए किस द्वितीयक रेफ्रिजरेंट का उपयोग किया जाता है? a) Chilled water / ठंडा पानी b) Brine (salt water solution) / ब्राइन (नमक के पानी का घोल) c) Glycol / ग्लाइकॉल d) Ammonia / अमोनिया 3. What is the main purpose of a vapor barrier in cold storage insulation?3. कोल्ड स्टोरेज इन्सुलेशन में वेपर बैरियर का मुख्य उद्देश्य क्या है? a) To provide structural support / संरचनात्मक समर्थन प्रदान करना b) To prevent moisture from migrating into the insulation / नमी को इन्सुलेशन में जाने से रोकना c) To make the insulation look better / इन्सुलेशन को बेहतर दिखाना d) To reflect heat / गर्मी को प्रतिबिंबित करना 4. In a car AC system, leak detection using UV dye involves:4. एक कार एसी प्रणाली में, यूवी डाई का उपयोग करके रिसाव का पता लगाने में शामिल है: a) Spraying dye on the outside of the pipes / पाइप के बाहर डाई का छिड़काव करना b) Adding a fluorescent dye to the refrigerant system and looking for leaks with a UV light / रेफ्रिजरेंट सिस्टम में एक फ्लोरोसेंट डाई मिलाना और यूवी लाइट से रिसाव की तलाश करना c) Checking the color of the refrigerant oil / रेफ्रिजरेंट तेल के रंग की जाँच करना d) Using a special camera that sees dye / एक विशेष कैमरे का उपयोग करना जो डाई को देखता है 5. A Variable Frequency Drive (VFD) is used in HVAC systems to control the:5. एचवीएसी सिस्टम में एक वेरिएबल फ्रीक्वेंसी ड्राइव (VFD) का उपयोग नियंत्रित करने के लिए किया जाता है: a) Temperature / तापमान b) Humidity / आर्द्रता c) Speed of motors (for fans or compressors) / मोटरों की गति (पंखों या कंप्रेसर के लिए) d) On/off cycle / ऑन/ऑफ चक्र 6. The process of adjusting dampers and airflow to meet design specifications in each room is known as:6. प्रत्येक कमरे में डिजाइन विनिर्देशों को पूरा करने के लिए डैम्पर्स और एयरफ्लो को समायोजित करने की प्रक्रिया कहलाती है: a) Commissioning / कमीशनिंग b) Air balancing / एयर बैलेंसिंग c) Duct cleaning / डक्ट की सफाई d) System charging / सिस्टम चार्जिंग 7. A key feature of a VRF/VRV system is:7. एक VRF/VRV प्रणाली की एक प्रमुख विशेषता है: a) It uses water instead of refrigerant / यह रेफ्रिजरेंट के बजाय पानी का उपयोग करता है b) One outdoor unit can connect to multiple indoor units with individual control / एक आउटडोर यूनिट व्यक्तिगत नियंत्रण के साथ कई इनडोर इकाइयों से जुड़ सकती है c) It is only used for heating / इसका उपयोग केवल हीटिंग के लिए किया जाता है d) It requires very large ducts / इसके लिए बहुत बड़े डक्ट की आवश्यकता होती है 8. In a system with an orifice tube, which component is used that is not typically found in a TXV system?8. एक ऑर्फिस ट्यूब वाले सिस्टम में, किस घटक का उपयोग किया जाता है जो आमतौर पर TXV सिस्टम में नहीं पाया जाता है? a) A condenser / एक कंडेनसर b) An accumulator / एक एक्यूमुलेटर c) An evaporator / एक इवैपोरेटर d) A compressor / एक कंप्रेसर 9. The temperature difference between the cold water leaving a cooling tower and the entering air’s wet-bulb temperature is known as:9. एक कूलिंग टॉवर से निकलने वाले ठंडे पानी और प्रवेश करने वाली हवा के वेट-बल्ब तापमान के बीच के तापमान के अंतर को कहा जाता है: a) Range / रेंज b) Approach / एप्रोच c) Drift / ड्रिफ्ट d) Lift / लिफ्ट 10. What is a cascade refrigeration system used for?10. एक कैस्केड प्रशीतन प्रणाली का उपयोग किस लिए किया जाता है? a) Standard air conditioning / मानक एयर कंडीशनिंग b) Car air conditioning / कार एयर कंडीशनिंग c) Achieving very low temperatures (ultra-low freezers) / बहुत कम तापमान (अल्ट्रा-लो फ्रीजर) प्राप्त करना d) Small domestic refrigerators / छोटे घरेलू रेफ्रिजरेटर 11. An electrical diagram showing the physical location of components is a:11. घटकों का भौतिक स्थान दिखाने वाला एक विद्युत आरेख है: a) Schematic diagram / योजनाबद्ध आरेख (Schematic diagram) b) Ladder diagram / लैडर आरेख c) Wiring or Layout diagram / वायरिंग या लेआउट आरेख d) One-line diagram / एक-लाइन आरेख 12. What does the acronym AHU stand for in HVAC?12. एचवीएसी में AHU का क्या अर्थ है? a) Air Humidity Unit / एयर ह्यूमिडिटी यूनिट b) Absolute Heating Unit / एब्सोल्यूट हीटिंग यूनिट c) Air Handling Unit / एयर हैंडलिंग यूनिट d) Automatic Heat Utility / ऑटोमैटिक हीट यूटिलिटी 13. The purpose of a Low-Pressure Cut-Out (LPCO) switch is to protect the:13. एक लो-प्रेशर कट-आउट (LPCO) स्विच का उद्देश्य किसकी रक्षा करना है: a) Condenser fan from over-speeding / कंडेनसर पंखे को ओवर-स्पीडिंग से b) Evaporator from freezing / इवैपोरेटर को जमने से c) Compressor from damage due to low suction pressure / कम सक्शन दाब के कारण कंप्रेसर को क्षति से d) System from high pressure / सिस्टम को उच्च दाब से 14. A centrifugal chiller compressor increases pressure by:14. एक सेंट्रीफ्यूगल चिलर कंप्रेसर दाब बढ़ाता है: a) Squeezing the gas between two scrolls / दो स्क्रॉल के बीच गैस को निचोड़कर b) Using a piston to compress the gas / गैस को संपीड़ित करने के लिए एक पिस्टन का उपयोग करके c) Using a high-speed impeller to throw the gas outwards / गैस को बाहर की ओर फेंकने के लिए एक उच्च गति वाले इंपेलर का उपयोग करके d) Absorbing the gas into a liquid / गैस को एक तरल में अवशोषित करके 15. A clogged air filter in a rooftop package unit will most likely cause:15. एक रूफटॉप पैकेज यूनिट में एक बंद एयर फिल्टर सबसे अधिक संभावना इसका कारण बनेगा: a) High head pressure / उच्च हेड प्रेशर b) Low suction pressure and evaporator coil freezing / निम्न सक्शन प्रेशर और इवैपोरेटर कॉइल का जमना c) The condenser fan to stop / कंडेनसर पंखे का रुकना d) The unit to cool better / यूनिट का बेहतर ठंडा करना 16. The term “lift” in relation to a chiller refers to:16. एक चिलर के संबंध में “लिफ्ट” शब्द का अर्थ है: a) The physical weight of the chiller / चिलर का भौतिक वजन b) The height the chiller is installed at / वह ऊंचाई जिस पर चिलर स्थापित है c) The pressure difference the compressor must work against (Condenser pressure – Evaporator pressure) / वह दाब अंतर जिसके विरुद्ध कंप्रेसर को काम करना पड़ता है (कंडेनसर दाब – इवैपोरेटर दाब) d) The speed of the compressor / कंप्रेसर की गति 17. An Electronic Expansion Valve (EEV) provides more precise refrigerant control than a:17. एक इलेक्ट्रॉनिक विस्तार वाल्व (EEV) किससे अधिक सटीक रेफ्रिजरेंट नियंत्रण प्रदान करता है: a) Compressor / कंप्रेसर b) Condenser / कंडेनसर c) Mechanical TXV or Capillary Tube / मैकेनिकल TXV या कैपिलरी ट्यूब d) Solenoid valve / सोलनॉइड वाल्व 18. In a duct system, a Volume Control Damper (VCD) is used to:18. एक डक्ट प्रणाली में, एक वॉल्यूम कंट्रोल डैम्पर (VCD) का उपयोग किया जाता है: a) Stop the flow of air completely in case of fire / आग लगने की स्थिति में हवा के प्रवाह को पूरी तरह से रोकना b) Regulate the quantity of air flowing through a branch duct / एक शाखा डक्ट के माध्यम से बहने वाली हवा की मात्रा को नियंत्रित करना c) Filter the air / हवा को फ़िल्टर करना d) Mix fresh air with return air / ताजी हवा को वापसी हवा के साथ मिलाना 19. The process of cleaning refrigerant by passing it through filter-driers is known as:19. फ़िल्टर-ड्रायर के माध्यम से रेफ्रिजरेंट को गुजारकर साफ करने की प्रक्रिया कहलाती है: a) Reclaiming / रिक्लेमिंग b) Recovery / रिकवरी c) Recycling / रीसाइक्लिंग d) Retrofitting / रेट्रोफिटिंग 20. What does CFM stand for?20. CFM का क्या अर्थ है? a) Centigrade Fahrenheit Measurement / सेंटीग्रेड फारेनहाइट मेजरमेंट b) Cubic Feet per Minute / क्यूबिक फीट प्रति मिनट c) Compressor Fan Motor / कंप्रेसर फैन मोटर d) Cooling Flow Mover / कूलिंग फ्लो मूवर 21. PUF panels used for cold storage walls are a type of:21. कोल्ड स्टोरेज की दीवारों के लिए उपयोग किए जाने वाले PUF पैनल एक प्रकार हैं: a) Structural support panel / संरचनात्मक समर्थन पैनल b) Insulated sandwich panel / इंसुलेटेड सैंडविच पैनल c) Decorative wall panel / सजावटी दीवार पैनल d) Soundproofing panel / साउंडप्रूफिंग पैनल 22. What is a common symptom of refrigerant overcharge?22. रेफ्रिजरेंट ओवरचार्ज का एक सामान्य लक्षण क्या है? a) Low suction and low discharge pressure / निम्न सक्शन और निम्न डिस्चार्ज दाब b) Bubbles in the sight glass / साइट ग्लास में बुलबुले c) High suction and high discharge pressure / उच्च सक्शन और उच्च डिस्चार्ज दाब d) The compressor does not start / कंप्रेसर चालू नहीं होता है 23. A phase failure relay is used in a three-phase system to:23. एक तीन-चरण प्रणाली में एक फेज फेलियर रिले का उपयोग किया जाता है: a) Protect equipment in case one of the phases is lost / किसी एक फेज के खो जाने की स्थिति में उपकरण की रक्षा करना b) Increase the voltage of the system / सिस्टम का वोल्टेज बढ़ाना c) Change the phase sequence / फेज अनुक्रम बदलना d) Balance the load on all phases / सभी फेजों पर लोड को संतुलित करना 24. In an absorption refrigeration system, what is used instead of a mechanical compressor?24. एक अवशोषण प्रशीतन प्रणाली में, एक यांत्रिक कंप्रेसर के बजाय क्या उपयोग किया जाता है? a) A pump and a generator (heat source) / एक पंप और एक जनरेटर (ऊष्मा स्रोत) b) A turbine / एक टरबाइन c) A large fan / एक बड़ा पंखा d) A chemical reaction only / केवल एक रासायनिक प्रतिक्रिया 25. A “walk-in cooler” is an example of:25. एक “वॉक-इन कूलर” एक उदाहरण है: a) Domestic refrigeration / घरेलू प्रशीतन का b) Commercial refrigeration / वाणिज्यिक प्रशीतन का c) Industrial refrigeration / औद्योगिक प्रशीतन का d) Transport refrigeration / परिवहन प्रशीतन का ← Previous Next → Finish Test / टेस्ट खत्म करें